[PATCH v9 5/5] arm64: dts: mt7986: add Bananapi R3

From: Frank Wunderlich
Date: Fri Jan 06 2023 - 10:29:48 EST


From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>

Add support for Bananapi R3 SBC.

- SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
- SPI-NAND/NOR support (switched CS by sw5/C)
- all rj45 ports and both SFP working (eth1/lan4)
- all USB-Ports + SIM-Slot tested
- i2c and all uarts tested
- wifi tested (with eeprom calibration data)

The device can boot from all 4 storage options. Both, SPI and MMC, can
be switched using hardware switches on the board, see
https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting

Signed-off-by: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
---
changes:
v9:
- drop model string override in sd-dtso

v8:
- drop model string override in emmc-dtso
- drop cs-gpios from spi-nodes
- add interrupt-settings for mt7531 switch

v7:
- squashed overlay-patch and converted sd/emmc dts to overlay too
- moved mmc-regulators to base dts
- changed common dtsi to (base dts) and overlay extension to dtso

v6:
- drop usb 5v regulator from bpi-r3
based on chunfengs response it is only needed if regulator is
switched (like for otg), usb works without it.

v4:
- add PCIe nodes
- fix sfp-properties of sfp-1 (need to be plural)
thx to Denis Odintsov for this

v3:
- rename factory-key to reset-key
- add dcin regulator and add it as input for 3v3 (with renaming)
- remove memory-node
- dropped wifi eeprom (calibration) data
- move mmc0 pinctrl to common dtsi and drop sdcard comment
- change mmc pull-up/down to have generic bias-pull*

v2:
- remove pcie to be added later (discussion about clocks)
- some fixes based on suggestions on ML
- add key suffix like it's done in mt7622-bpi-r64 devicetree
- add dash in sfp node names
- use reg as unit for switch-node
- drop "-3-4" suffix from i2c-pins node name
- fix order in Makefile
---
arch/arm64/boot/dts/mediatek/Makefile | 5 +
.../mt7986a-bananapi-bpi-r3-emmc.dtso | 29 ++
.../mt7986a-bananapi-bpi-r3-nand.dtso | 55 +++
.../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso | 68 +++
.../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso | 23 +
.../dts/mediatek/mt7986a-bananapi-bpi-r3.dts | 450 ++++++++++++++++++
6 files changed, 630 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96..d5cd7b3e09cf 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -8,6 +8,11 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtbo
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
new file mode 100644
index 000000000000..779dc6782bb1
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@xxxxxxxxxxxx>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+ compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+ fragment@0 {
+ target-path = "/soc/mmc@11230000";
+ __overlay__ {
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ hs400-ds-delay = <0x14014>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ status = "okay";
+ };
+ };
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
new file mode 100644
index 000000000000..15ee8c568f3c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@xxxxxxxxxxxxxx>
+ * Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+ compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+ fragment@0 {
+ target-path = "/soc/spi@1100a000";
+ __overlay__ {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ spi_nand: spi_nand@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ spi-tx-buswidth = <4>;
+ spi-rx-buswidth = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "bl2";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "reserved";
+ reg = <0x80000 0x300000>;
+ };
+
+ partition@380000 {
+ label = "fip";
+ reg = <0x380000 0x200000>;
+ read-only;
+ };
+
+ partition@580000 {
+ label = "ubi";
+ reg = <0x580000 0x7a80000>;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
new file mode 100644
index 000000000000..84aa229e80f3
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@xxxxxxxxxxxxxx>
+ * Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+ compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+ fragment@0 {
+ target-path = "/soc/spi@1100a000";
+ __overlay__ {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "bl2";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ partition@20000 {
+ label = "reserved";
+ reg = <0x20000 0x20000>;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x40000 0x40000>;
+ };
+
+ partition@80000 {
+ label = "reserved2";
+ reg = <0x80000 0x80000>;
+ };
+
+ partition@100000 {
+ label = "fip";
+ reg = <0x100000 0x80000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "recovery";
+ reg = <0x180000 0xa80000>;
+ };
+
+ partition@c00000 {
+ label = "fit";
+ reg = <0xc00000 0x1400000>;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
new file mode 100644
index 000000000000..f623bce075ce
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@xxxxxxxxxxxx>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+ compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+ fragment@0 {
+ target-path = "/soc/mmc@11230000";
+ __overlay__ {
+ bus-width = <4>;
+ max-frequency = <52000000>;
+ cap-sd-highspeed;
+ status = "okay";
+ };
+ };
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
new file mode 100644
index 000000000000..33bd6febc160
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Authors: Sam.Shih <sam.shih@xxxxxxxxxxxx>
+ * Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
+ * Daniel Golle <daniel@xxxxxxxxxxxxxx>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+ model = "Bananapi BPI-R3";
+ compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+ aliases {
+ serial0 = &uart0;
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ dcin: regulator-12vd {
+ compatible = "regulator-fixed";
+ regulator-name = "12vd";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset-key {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ };
+
+ wps-key {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ /* i2c of the left SFP cage (wan) */
+ i2c_sfp1: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ /* i2c of the right SFP cage (lan) */
+ i2c_sfp2: i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ green_led: led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ blue_led: led-1 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1.8vd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ vin-supply = <&dcin>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3.3vd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ vin-supply = <&dcin>;
+ };
+
+ /* left SFP cage (wan) */
+ sfp1: sfp-1 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp1>;
+ los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* right SFP cage (lan) */
+ sfp2: sfp-2 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp2>;
+ los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+&eth {
+ status = "okay";
+
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ gmac1: mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "2500base-x";
+ sfp = <&sfp1>;
+ managed = "in-band-status";
+ };
+
+ mdio: mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+&mdio {
+ switch: switch@31 {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+ reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_pins_default>;
+ pinctrl-1 = <&mmc0_pins_uhs>;
+ vmmc-supply = <&reg_3p3v>;
+ vqmmc-supply = <&reg_1p8v>;
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_pins>;
+ status = "okay";
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_pins>;
+ status = "okay";
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pio {
+ i2c_pins: i2c-pins {
+ mux {
+ function = "i2c";
+ groups = "i2c";
+ };
+ };
+
+ mmc0_pins_default: mmc0-pins {
+ mux {
+ function = "emmc";
+ groups = "emmc_51";
+ };
+ conf-cmd-dat {
+ pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+ "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+ "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+ input-enable;
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ conf-clk {
+ pins = "EMMC_CK";
+ drive-strength = <6>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-ds {
+ pins = "EMMC_DSL";
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-rst {
+ pins = "EMMC_RSTB";
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ };
+
+ mmc0_pins_uhs: mmc0-uhs-pins {
+ mux {
+ function = "emmc";
+ groups = "emmc_51";
+ };
+ conf-cmd-dat {
+ pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+ "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+ "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+ input-enable;
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ conf-clk {
+ pins = "EMMC_CK";
+ drive-strength = <6>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-ds {
+ pins = "EMMC_DSL";
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-rst {
+ pins = "EMMC_RSTB";
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ };
+
+ pcie_pins: pcie-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie_clk", "pcie_pereset";
+ };
+ };
+
+ spi_flash_pins: spi-flash-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ };
+
+ spic_pins: spic-pins {
+ mux {
+ function = "spi";
+ groups = "spi1_0";
+ };
+ };
+
+ uart1_pins: uart1-pins {
+ mux {
+ function = "uart";
+ groups = "uart1_rx_tx";
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ mux {
+ function = "uart";
+ groups = "uart2_0_rx_tx";
+ };
+ };
+
+ wf_2g_5g_pins: wf-2g-5g-pins {
+ mux {
+ function = "wifi";
+ groups = "wf_2g", "wf_5g";
+ };
+ conf {
+ pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+ "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+ "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+ "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+ "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+ "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+ "WF1_TOP_CLK", "WF1_TOP_DATA";
+ drive-strength = <4>;
+ };
+ };
+
+ wf_dbdc_pins: wf-dbdc-pins {
+ mux {
+ function = "wifi";
+ groups = "wf_dbdc";
+ };
+ conf {
+ pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+ "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+ "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+ "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+ "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+ "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+ "WF1_TOP_CLK", "WF1_TOP_DATA";
+ drive-strength = <4>;
+ };
+ };
+
+ wf_led_pins: wf-led-pins {
+ mux {
+ function = "led";
+ groups = "wifi_led";
+ };
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ status = "okay";
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spic_pins>;
+ status = "okay";
+};
+
+&ssusb {
+ status = "okay";
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "wan";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan0";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan1";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan2";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan3";
+ };
+
+ port5: port@5 {
+ reg = <5>;
+ label = "lan4";
+ phy-mode = "2500base-x";
+ sfp = <&sfp2>;
+ managed = "in-band-status";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&trng {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi {
+ status = "okay";
+ pinctrl-names = "default", "dbdc";
+ pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
+ pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
+};
+
--
2.34.1