Re:Re: [PATCH 2/2] arm64: dts: rockchip: Enable wifi module AP6398s for rk3566 box demo

From: Andy Yan
Date: Thu Dec 29 2022 - 07:11:46 EST





Hi Heiko:











At 2022-12-29 03:21:32, "Heiko Stuebner" <heiko@xxxxxxxxx> wrote:
>Hi Andy,
>
>Am Sonntag, 25. Dezember 2022, 12:49:53 CET schrieb Andy Yan:
>> There is a AP6398s wifi/bt module on this board.
>> Fix the sdmmc1 dt node to make wifi work.
>>
>> Fixes: 2e0537b16b25 ("arm64: dts: rockchip: Add dts for rockchip rk3566 box demo board")
>>
>> Signed-off-by: Andy Yan <andyshrk@xxxxxxx>
>> ---
>>
>> .../boot/dts/rockchip/rk3566-box-demo.dts | 26 ++++++++++++++++---
>> 1 file changed, 22 insertions(+), 4 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-box-demo.dts b/arch/arm64/boot/dts/rockchip/rk3566-box-demo.dts
>> index d956496d5221..6c0c24226b52 100644
>> --- a/arch/arm64/boot/dts/rockchip/rk3566-box-demo.dts
>> +++ b/arch/arm64/boot/dts/rockchip/rk3566-box-demo.dts
>> @@ -324,8 +324,12 @@ wifi_enable_h: wifi-enable-h {
>> rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
>> };
>>
>> + wifi_host_wake_h: wifi-host-wake-l {
>> + rockchip,pins = <2 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> +
>> wifi_32k: wifi-32k {
>> - rockchip,pins = <0 RK_PB0 2 &pcfg_pull_none>;
>> + rockchip,pins = <2 RK_PC6 1 &pcfg_pull_none>;
>> };
>> };
>>
>> @@ -391,16 +395,30 @@ &sdmmc0 {
>> };
>>
>> &sdmmc1 {
>> + /* WiFi & BT combo module AMPAK AP6398S */
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> bus-width = <4>;
>> + clock-frequency = <150000000>;
>> + cap-sdio-irq;
>> cap-sd-highspeed;
>> - disable-wp;
>> + sd-uhs-sdr104;
>> + keep-power-in-suspend;
>> mmc-pwrseq = <&sdio_pwrseq>;
>> non-removable;
>> pinctrl-names = "default";
>> pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
>> - vmmc-supply = <&vcc_3v3>;
>> - vqmmc-supply = <&vcca_1v8>;
>
>why are you removing the mmc-supplies here?
>The supplies needed for mmc to work should very much be present
>I think, especially to also make sure something else doesn't
>turn them off.

Thanks for catching this, I will fix it in V2.

>
>Heiko
>
>> status = "okay";
>> +
>> + brcmf: wifi@1 {
>> + compatible = "brcm,bcm4329-fmac";
>> + reg = <1>;
>> + interrupt-parent = <&gpio2>;
>> + interrupts = <RK_PB2 GPIO_ACTIVE_HIGH>;
>> + interrupt-names = "host-wake";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&wifi_host_wake_h>;
>> + };
>> };
>>
>> &spdif {
>>
>
>
>