Re: [RFC PATCH 3/6] drm/msm/dpu1: Wire up DSC mask for active CTL configuration
From: Dmitry Baryshkov
Date: Wed Dec 14 2022 - 20:08:24 EST
On 14/12/2022 21:30, Marijn Suijten wrote:
On 2022-12-14 20:43:29, Dmitry Baryshkov wrote:
On 14/12/2022 01:22, Marijn Suijten wrote:
Active CTLs have to configure what DSC block(s) have to be enabled, and
what DSC block(s) have to be flushed; this value was initialized to zero
resulting in the necessary register writes to never happen (or would
write zero otherwise). This seems to have gotten lost in the DSC v4->v5
series while refactoring how the combination with merge_3d was handled.
Fixes: 58dca9810749 ("drm/msm/disp/dpu1: Add support for DSC in encoder")
Signed-off-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx>
---
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c | 1 +
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 1 +
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c | 2 ++
3 files changed, 4 insertions(+)
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
index ae28b2b93e69..35791f93c33d 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
@@ -61,6 +61,7 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg(
intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_CMD;
intf_cfg.stream_sel = cmd_enc->stream_sel;
intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc);
+ intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc);
ctl->ops.setup_intf_cfg(ctl, &intf_cfg);
/* setup which pp blk will connect to this intf */
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
index 0f71e8fe7be7..9ee3a7306a5f 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
@@ -274,6 +274,7 @@ static void dpu_encoder_phys_vid_setup_timing_engine(
intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_VID;
intf_cfg.stream_sel = 0; /* Don't care value for video mode */
intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc);
+ intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc);
if (phys_enc->hw_pp->merge_3d)
intf_cfg.merge_3d = phys_enc->hw_pp->merge_3d->idx;
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c
index 7cbcef6efe17..92ddf9995b37 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c
@@ -209,6 +209,7 @@ static void dpu_encoder_phys_wb_setup_cdp(struct dpu_encoder_phys *phys_enc)
intf_cfg.intf = DPU_NONE;
intf_cfg.wb = hw_wb->idx;
+ intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc);
We usually don't have DSC with the writeback, don't we?
I am unsure so ended up adding them in writeback regardless. Downstream
uses a separate callback to process intf_cfg.dsc instead of going
through setup_intf_cfg().
To prevent these from being missed again (in the case of copy&paste),
how about instead having some function that sets up intf_cfg with these
default values from a phys_enc? That way most of this remains oblivious
to the caller.
I'm not sure this is possible. E.g. intf_cfg.dsc should not be set for
the WB.
On the same note, that callback on non-DPU_CTL_ACTIVE_CFG hardware
doesn't use the intf_cfg.dsc member anyway, but it was again added to
keep the blocks somewhat consistent (in case it ever becomes used?).
if (mode_3d && hw_pp && hw_pp->merge_3d)
intf_cfg.merge_3d = hw_pp->merge_3d->idx;
@@ -230,6 +231,7 @@ static void dpu_encoder_phys_wb_setup_cdp(struct dpu_encoder_phys *phys_enc)
intf_cfg.wb = hw_wb->idx;
intf_cfg.mode_3d =
dpu_encoder_helper_get_3d_blend_mode(phys_enc);
+ intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc);
phys_enc->hw_ctl->ops.setup_intf_cfg(phys_enc->hw_ctl, &intf_cfg);
}
}
- Marijn
--
With best wishes
Dmitry