Re: [PATCH V2 3/3] Input: elantech - Fix incorrectly halved touchpad range on ELAN v3 touchpads

From: Dmitry Torokhov
Date: Mon Nov 28 2022 - 13:15:43 EST


On Fri, Oct 14, 2022 at 04:15:33AM -0700, Eirin Nya wrote:
> On Linux 5.19.10, on my laptop (Dell Inspiron 15R SE 7520) with an Elan
> v3 touchpad (dmesg says "with firmware version 0x450f02"), the reported
> size of my touchpad (in userspace by calling mtdev_configure() and
> libevdev_get_abs_maximum(), in kernel space
> elantech_device_info::x_max/y_max, either way 1470 by 700) is half that
> of the actual touch range (2940 by 1400), and the upper half of my
> touchpad reports negative values. As a result, with the Synaptics or
> libinput X11 driver set to edge scrolling mode, the entire right half of
> my touchpad has x-values past evdev's reported maximum size, and acts as
> a giant scrollbar!
>
> The problem is that elantech_setup_ps2() -> elantech_set_absolute_mode()
> sets up absolute mode and doubles the hardware resolution (doubling the
> hardware's maximum reported x/y coordinates and its response to
> ETP_FW_ID_QUERY), *after* elantech_query_info() fetches the touchpad
> coordinate system size using ETP_FW_ID_QUERY, which gets cached and
> reported to userspace through ioctl(fd, EVIOCGABS(ABS_X/Y), ...). So the
> touchpad size reported to userspace (and used to subtract vertical
> coordinates from) is half the maximum position of actual touches.
>
> This patch splits out a function elantech_query_range_v3() which fetches
> *only* ETP_FW_ID_QUERY (touchpad size), and calls it a second time if
> elantech_set_absolute_mode() enables double-size mode. This means the
> first call is redundant and wasted if a second call occurs, but this
> minimizes the need to restructure the driver.

If the setting is indeed double resolution, can we simply multiply x_max
and y_max by 2 instead of re-querying it?

Also let's try adding one of Elan engineers for their take in this.
Phoenix, do you have any suggestions please?

>
> Link: https://lore.kernel.org/linux-input/CAL57YxZNutUVxBtvbVWKMw-V2kqeVB5kTQ5BFdJmN=mdPq8Q8Q@xxxxxxxxxxxxxx/
> Link: https://lore.kernel.org/linux-input/20221008093437.72d0f6b0@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx/
> Fixes: 37548659bb22 ("Input: elantech - query the min/max information beforehand too")
> Signed-off-by: Eirin Nya <nyanpasu256@xxxxxxxxx>
> ---
>
> Notes:
> Should we move (elantech_set_absolute_mode ->
> elantech_write_reg(...0x0b or 0x01)) *earlier* into elantech_query_info()
> before "query range information"? See discussion at
> https://lore.kernel.org/linux-input/20221008093437.72d0f6b0@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx/
>
> drivers/input/mouse/elantech.c | 30 ++++++++++++++++++++++++++----
> 1 file changed, 26 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/input/mouse/elantech.c b/drivers/input/mouse/elantech.c
> index 263779c031..a2176f0fd3 100644
> --- a/drivers/input/mouse/elantech.c
> +++ b/drivers/input/mouse/elantech.c
> @@ -1006,6 +1006,9 @@ static void elantech_set_rate_restore_reg_07(struct psmouse *psmouse,
> psmouse_err(psmouse, "restoring reg_07 failed\n");
> }
>
> +static int elantech_query_range_v3(struct psmouse *psmouse,
> + struct elantech_device_info *info);
> +
> /*
> * Put the touchpad into absolute mode
> */
> @@ -1047,6 +1050,14 @@ static int elantech_set_absolute_mode(struct psmouse *psmouse)
> if (elantech_write_reg(psmouse, 0x10, etd->reg_10))
> rc = -1;
>
> + /*
> + * If we boost hardware resolution, we have to re-query
> + * info->x_max and y_max.
> + */
> + if (etd->info.set_hw_resolution)
> + if (elantech_query_range_v3(psmouse, &etd->info))
> + rc = -1;
> +
> break;
>
> case 4:
> @@ -1671,6 +1682,20 @@ static int elantech_set_properties(struct elantech_device_info *info)
> return 0;
> }
>
> +static int elantech_query_range_v3(struct psmouse *psmouse,
> + struct elantech_device_info *info)
> +{
> + unsigned char param[3];
> +
> + if (info->send_cmd(psmouse, ETP_FW_ID_QUERY, param))
> + return -EINVAL;
> +
> + info->x_max = (0x0f & param[0]) << 8 | param[1];
> + info->y_max = (0xf0 & param[0]) << 4 | param[2];
> +
> + return 0;
> +}
> +
> static int elantech_query_info(struct psmouse *psmouse,
> struct elantech_device_info *info)
> {
> @@ -1826,11 +1851,8 @@ static int elantech_query_info(struct psmouse *psmouse,
> break;
>
> case 3:
> - if (info->send_cmd(psmouse, ETP_FW_ID_QUERY, param))
> + if (elantech_query_range_v3(psmouse, info))
> return -EINVAL;
> -
> - info->x_max = (0x0f & param[0]) << 8 | param[1];
> - info->y_max = (0xf0 & param[0]) << 4 | param[2];
> break;
>
> case 4:
> --
> 2.38.0
>

Thanks.

--
Dmitry