Re: [PATCH v11 1/2] thermal: Add thermal driver for Sunplus

[Daniel Lezcano]

On 18/10/2022 09:32, Li-hao Kuo wrote:
> Add thermal driver for Sunplus.
>
> Signed-off-by: Li-hao Kuo <lhjeff911@xxxxxxxxx>
> ---
> Changes in v11:
>   - Remove the remove function of the platform_driver
>   - Fix error reported-by: kernel test robot.
>
>   MAINTAINERS                       |   6 ++
>   drivers/thermal/Kconfig           |  10 +++
>   drivers/thermal/Makefile          |   1 +
>   drivers/thermal/sunplus_thermal.c | 130 ++++++++++++++++++++++++++++++++++++++
>   4 files changed, 147 insertions(+)
>   create mode 100644 drivers/thermal/sunplus_thermal.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index cf0f185..bf22c53 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -19753,6 +19753,12 @@ S:	Maintained
>   F:	Documentation/devicetree/bindings/spi/spi-sunplus-sp7021.yaml
>   F:	drivers/spi/spi-sunplus-sp7021.c
>   
> +SUNPLUS THERMAL DRIVER
> +M:	Li-hao Kuo <lhjeff911@xxxxxxxxx>
> +L:	linux-pm@xxxxxxxxxxxxxxx
> +S:	Maintained
> +F:	drivers/thermal/sunplus_thermal.c
> +
>   SUNPLUS UART DRIVER
>   M:	Hammer Hsieh <hammerh0314@xxxxxxxxx>
>   S:	Maintained
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index e052dae..405b788 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -504,4 +504,14 @@ config KHADAS_MCU_FAN_THERMAL
>   	  If you say yes here you get support for the FAN controlled
>   	  by the Microcontroller found on the Khadas VIM boards.
>   
> +config SUNPLUS_THERMAL
> +	tristate "Sunplus thermal drivers"
> +	depends on SOC_SP7021 || COMPILE_TEST
> +	help
> +	  This enable the Sunplus SP7021 thermal driver, which supports the primitive
> +	  temperature sensor embedded in Sunplus SP7021 SoC.
> +
> +	  If you have a Sunplus SP7021 platform say Y here and enable this option
> +	  to have support for thermal management.
> +
>   endif
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 2506c6c..4512193 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -61,3 +61,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
>   obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
>   obj-$(CONFIG_SPRD_THERMAL)	+= sprd_thermal.o
>   obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL)	+= khadas_mcu_fan.o
> +obj-$(CONFIG_SUNPLUS_THERMAL)	+= sunplus_thermal.o
> \ No newline at end of file
> diff --git a/drivers/thermal/sunplus_thermal.c b/drivers/thermal/sunplus_thermal.c
> new file mode 100644
> index 0000000..20ea7d9
> --- /dev/null
> +++ b/drivers/thermal/sunplus_thermal.c
> @@ -0,0 +1,130 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) Sunplus Inc.
> + * Author: Li-hao Kuo <lhjeff911@xxxxxxxxx>
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/nvmem-consumer.h>
> +#include <linux/platform_device.h>
> +#include <linux/reset.h>
> +#include <linux/thermal.h>
> +
> +#define ENABLE_THERMAL		BIT(31)
> +#define SP_THERMAL_MASK		GENMASK(10, 0)
> +
> +#define TEMP_RATE		608
> +#define TEMP_BASE		3500
> +#define TEMP_OTP_BASE		1518
> +
> +#define SP_THERMAL_CTL0_REG	0x0000
> +#define SP_THERMAL_STS0_REG	0x0030
> +
> +/* common data structures */
> +struct sp_thermal_data {
> +	struct thermal_zone_device *pcb_tz;
> +	void __iomem *regs;
> +	int *otp_temp0;
> +};
> +
> +static int sunplus_get_otp_temp_coef(struct sp_thermal_data *sp_data, struct device *dev)
> +{
> +	struct nvmem_cell *cell;
> +	ssize_t otp_l;
> +
> +	cell = nvmem_cell_get(dev, "calib");
> +	if (IS_ERR(cell))
> +		return PTR_ERR(cell);
> +
> +	sp_data->otp_temp0 = nvmem_cell_read(cell, &otp_l);
> +	nvmem_cell_put(cell);
> +
> +	if (*sp_data->otp_temp0 == 0)
> +		*sp_data->otp_temp0 = TEMP_OTP_BASE;
> +
> +	return 0;
> +}
> +
> +/*
> + * There is a thermal sensor instance for Sunplus Soc
> + * T_CODE is the ADC of the thermal sensor
> + * T_CODE : 11 digits in total
> + * When remanufacturing, the 35 degree T_CODE will be read and stored in nvcell.
> + * otp_temp0 is the 35 degree T_CODE obtained from nvcell
> + * The function will get 35 degree T_CODE for thermal calibration.
> + * TEMP_RATE is the Sunplus thermal temperature slope.
> + */
> +
> +static int sp_thermal_get_sensor_temp(void *data, int *temp)
> +{
> +	struct sp_thermal_data *sp_data = data;
> +	int t_code;
> +
> +	t_code = readl(sp_data->regs + SP_THERMAL_STS0_REG);
> +	t_code = FIELD_GET(SP_THERMAL_MASK, t_code);
> +	*temp = ((*sp_data->otp_temp0 - t_code) * 10000 / TEMP_RATE) + TEMP_BASE;
> +	*temp *= 10;
> +	return 0;
> +}
> +
> +static const struct thermal_zone_of_device_ops sp_of_thermal_ops = {

struct thermal_zone_device_ops ...


https://lore.kernel.org/r/20220804224349.1926752-1-daniel.lezcano@xxxxxxxxxx





--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog