Re: [PATCH net-next v4 1/5] net: ipqess: introduce the Qualcomm IPQESS driver

[Krzysztof Kozlowski]

On 09/09/2022 17:24, Maxime Chevallier wrote:
> The Qualcomm IPQESS controller is a simple 1G Ethernet controller found
> on the IPQ4019 chip. This controller has some specificities, in that the
> IPQ4019 platform that includes that controller also has an internal
> switch, based on the QCA8K IP.
> 
> It is connected to that switch through an internal link, and doesn't
> expose directly any external interface, hence it only supports the
> PHY_INTERFACE_MODE_INTERNAL for now.
> 
> It has 16 RX and TX queues, with a very basic RSS fanout configured at

Thank you for your patch. There is something to discuss/improve.

> +}
> +
> +static int ipqess_axi_probe(struct platform_device *pdev)
> +{
> +	struct device_node *np = pdev->dev.of_node;
> +	struct net_device *netdev;
> +	phy_interface_t phy_mode;
> +	struct resource *res;
> +	struct ipqess *ess;
> +	int i, err = 0;
> +
> +	netdev = devm_alloc_etherdev_mqs(&pdev->dev, sizeof(struct ipqess),

sizeof(*)

> +					 IPQESS_NETDEV_QUEUES,
> +					 IPQESS_NETDEV_QUEUES);
> +	if (!netdev)
> +		return -ENOMEM;
> +
> +	ess = netdev_priv(netdev);
> +	ess->netdev = netdev;
> +	ess->pdev = pdev;
> +	spin_lock_init(&ess->stats_lock);
> +	SET_NETDEV_DEV(netdev, &pdev->dev);
> +	platform_set_drvdata(pdev, netdev);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	ess->hw_addr = devm_ioremap_resource(&pdev->dev, res);

Use a helper for this.

> +	if (IS_ERR(ess->hw_addr))
> +		return PTR_ERR(ess->hw_addr);
> +
> +	err = of_get_phy_mode(np, &phy_mode);
> +	if (err) {
> +		dev_err(&pdev->dev, "incorrect phy-mode\n");
> +		return err;
> +	}
> +
> +	ess->ess_clk = devm_clk_get(&pdev->dev, "ess");

There is no such clock "ess"...

> +	if (!IS_ERR(ess->ess_clk))
> +		clk_prepare_enable(ess->ess_clk);
> +
> +	ess->ess_rst = devm_reset_control_get(&pdev->dev, "ess");

Same problem.

> +	if (IS_ERR(ess->ess_rst))
> +		goto err_clk;
> +
> +	ipqess_reset(ess);
> +
> +	ess->phylink_config.dev = &netdev->dev;
> +	ess->phylink_config.type = PHYLINK_NETDEV;
> +	ess->phylink_config.mac_capabilities = MAC_SYM_PAUSE | MAC_10 |
> +					       MAC_100 | MAC_1000FD;
> +
> +	__set_bit(PHY_INTERFACE_MODE_INTERNAL,
> +		  ess->phylink_config.supported_interfaces);
> +
> +	ess->phylink = phylink_create(&ess->phylink_config,
> +				      of_fwnode_handle(np), phy_mode,
> +				      &ipqess_phylink_mac_ops);
> +	if (IS_ERR(ess->phylink)) {
> +		err = PTR_ERR(ess->phylink);
> +		goto err_clk;
> +	}
> +

Best regards,
Krzysztof