Re: [PATCH v2] media: imx7-media-csi: Add support for fast-tracking queued buffers

From: Laurent Pinchart
Date: Thu Sep 08 2022 - 04:35:39 EST


Hi Paul,

On Thu, Sep 08, 2022 at 12:03:21PM +0900, paul.elder@xxxxxxxxxxxxxxxx wrote:
> On Wed, Sep 07, 2022 at 09:18:56PM +0300, Laurent Pinchart wrote:
> > On Wed, Sep 07, 2022 at 08:47:37PM +0900, Paul Elder wrote:
> > > The CSI hardware compatible with this driver handles buffers using a
> > > ping-pong mechanism with two sets of destination addresses. Normally,
> > > when an interrupt comes in to signal the completion of one buffer, say
> > > FB0, it assigns the next buffer in the queue to the next FB0, and the
> > > hardware starts to capture into FB1 in the meantime.
> >
> > Could you replace FB0 and FB1 with FB1 and FB2 respectively, to match
> > the naming of the registers ?
>
> Oops, I forgot to do it in the commit message.
>
> > > In a buffer underrun situation, in the above example without loss of
> > > generality, if a new buffer is queued before the interrupt for FB0 comes
> > > in, we can program the buffer into FB1 (which is programmed with a dummy
> > > buffer, as there is a buffer underrun).
> > >
> > > This of course races with the interrupt that signals FB0 completion, as
> > > once that interrupt comes in, we are no longer guaranteed that the
> > > programming of FB1 was in time and must assume it was too late. This
> > > race is resolved partly by locking the programming of FB1. If it came
> > > after the interrupt for FB0, then the variable that is used to determine
> > > which FB to program would have been swapped by the interrupt handler.
> > >
> > > This alone isn't sufficient, however, because the interrupt could still
> > > be generated (thus the hardware starts capturing into the other fb)
> > > while the fast-tracking routine has the irq lock. Thus, after
> > > programming the fb register to fast-track the buffer, the isr also must
> > > be checked to confirm that an interrupt didn't come in the meantime. If
> > > it has, we must assume that programming the register for the
> > > fast-tracked buffer was not in time, and queue the buffer normally.
> > >
> > > Signed-off-by: Paul Elder <paul.elder@xxxxxxxxxxxxxxxx>
> > > Acked-by: Rui Miguel Silva <rmfrfs@xxxxxxxxx>
> > >
> > > ---
> > > Changes in v2:
> > > - fix the potential race condition where the interrupt comes in while
> > > the fast tracking routine has the irqlock
> > > - change return value from int to bool
> > > ---
> > > drivers/staging/media/imx/imx7-media-csi.c | 63 ++++++++++++++++++++++
> > > 1 file changed, 63 insertions(+)
> > >
> > > diff --git a/drivers/staging/media/imx/imx7-media-csi.c b/drivers/staging/media/imx/imx7-media-csi.c
> > > index a0553c24cce4..0ebef44a7627 100644
> > > --- a/drivers/staging/media/imx/imx7-media-csi.c
> > > +++ b/drivers/staging/media/imx/imx7-media-csi.c
> > > @@ -1296,12 +1296,75 @@ static int imx7_csi_video_buf_prepare(struct vb2_buffer *vb)
> > > return 0;
> > > }
> > >
> > > +static bool imx7_csi_fast_track_buffer(struct imx7_csi *csi,
> > > + struct imx7_csi_vb2_buffer *buf)
> > > +{
> > > + unsigned long flags;
> > > + dma_addr_t phys;
> > > + int buf_num;
> > > + u32 isr;
> > > +
> > > + if (!csi->is_streaming)
> > > + return false;
> > > +
> > > + phys = vb2_dma_contig_plane_dma_addr(&buf->vbuf.vb2_buf, 0);
> > > +
> > > + /*
> > > + * buf_num holds the fb id of the most recently (*not* the next
> > > + * anticipated) triggered interrupt. Without loss of generality, if
> > > + * buf_num is 0 and we get to this section before the irq for fb2, the
> >
> > s/fb2/FB2/ to match hardware registers and the commit message ?
>
> ack
>
> >
> > > + * buffer that we are fast-tracking into fb1 should be programmed in
> > > + * time to be captured into. If the irq for fb2 already happened, then
> > > + * buf_num would be 1, and we would fast-track the buffer into fb2
> > > + * instead. This guarantees that we won't try to fast-track into fb1
> > > + * and race against the start-of-capture into fb1.
> > > + *
> > > + * We only fast-track the buffer if the currently programmed buffer is
> > > + * a dummy buffer. We can check the active_vb2_buf instead as it is
> > > + * always modified along with programming the fb[1,2] registers via the
> > > + * lock (besides setup and cleanup).
> > > + */
> >
> > I think this needs to be updated, it still indicates we handle the race
> > just by checking buf_num. How about the following ?
> >
> > /*
> > * buf_num holds the framebuffer ID of the most recently (*not* the next
> > * anticipated) triggered interrupt. Without loss of generality, if
> > * buf_num is 0, the hardware is capturing to FB2. If FB1 has been
> > * programmed with a dummy buffer (as indicated by active_vb2_buf[0]
> > * being NULL), then we can fast-track the new buffer by programming its
> > * address in FB1 before the hardware completes FB2, instead of adding
> > * it to the buffer queue and incurring a delay of one additional frame.
>
> Okay that's a lot easier to follow than the one that I wrote.
>
> > *
> > * The irqlock prevents races with the interrupt handler that queues the
>
> The interrupt handler doesn't /queue/ the buffer, it programs the FB
> register with the buffer at the front of the buffer queue. That's why I
> said "programs the next buffer" in my original text.

I meant queuing it to the hardware, in the sense that programming the
register doesn't make the hardware process the buffer immediately, but
you're right, that's not a good term here. I'll use "programs the next
buffer".

> Although I don't think racing with the interrupt handler for
> programming the next buffer is important in this context, since the
> interrupt handler is going to program FB2, while we're trying to program FB1
> before that that interrupt comes in.
>
> It's mainly buf_num that's relevant to locking the irqlock.

You're right. I'll write "that udpates buf_num when it programs the next
buffer".

> > * next buffer and updates buf_num, but we can still race with the
> > * hardware if we program the buffer in FB1 just after the hardware
> > * completes FB2 and switches to FB1 and before we notice the buf_num
> > * change.
>
> buf_num won't actually be changed because we have the lock. Maybe
> "before buf_num can be updated by the interrupt handler for FB2"?

Sounds good.

> > The fast-tracked buffer would then be ignored by the hardware
> > * while the driver would think it has successfully been processed.
> > *
> > * To avoid this problem, if we can't avoid the race, we can detect that
> > * we have lost it by checking, after programming the buffer in FB1, if
> > * the interrupt flag indicated completion of FB2 has been raised. If
>
> s/indicated/indicating/
>
> > * that is not the case, fast-tracking succeeded, and we can update
> > * active_vb2_buf[0]. Otherwise, we may or may not have lost the race
> > * (as the interrupt flag may have been raised just after programming
> > * FB1 and before we read the interrupt status register), and we need to
> > * assume the worst case of a race loss and queue the buffer through the
> > * slow path.
> > */
> >
> > Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> >
> > If you're fine with these changes there's no need to submit a v3, I'll
> > update the comment and the commit message locally.
>
> Yeah I'm fine with these.
>
> > > +
> > > + spin_lock_irqsave(&csi->irqlock, flags);
> > > +
> > > + buf_num = csi->buf_num;
> > > + if (csi->active_vb2_buf[buf_num]) {
> > > + spin_unlock_irqrestore(&csi->irqlock, flags);
> > > + return false;
> > > + }
> > > +
> > > + imx7_csi_update_buf(csi, phys, buf_num);
> > > +
> > > + isr = imx7_csi_reg_read(csi, CSI_CSISR);
> > > + /*
> > > + * The interrupt for the /other/ fb just came (the isr hasn't run yet
> > > + * though, because we have the lock here); we can't be sure we've
> > > + * programmed buf_num fb in time, so queue the buffer to the buffer
> > > + * queue normally. No need to undo writing the fb register, since we
> > > + * won't return it as active_vb2_buf is NULL, so it's okay to
> > > + * potentially write it to both fb1 and fb2; only the one where it was
>
> I guess there should be s/fb/FB/ throughout this block too.
>
> > > + * queued normally will be returned.
> > > + */
>
> (You mention this in your other reply)
>
> Yeah I guess this block should go inside the if. I didn't really
> aesthetically like a huge block of text inside a tiny if block but maybe
> that's more correct.
>
> > > + if (isr & (buf_num ? BIT_DMA_TSF_DONE_FB1 : BIT_DMA_TSF_DONE_FB2)) {
> > > + spin_unlock_irqrestore(&csi->irqlock, flags);
> > > + return false;
> > > + }
> > > +
> > > + csi->active_vb2_buf[buf_num] = buf;
> > > +
> > > + spin_unlock_irqrestore(&csi->irqlock, flags);
> > > + return true;
> > > +}
> > > +
> > > static void imx7_csi_video_buf_queue(struct vb2_buffer *vb)
> > > {
> > > struct imx7_csi *csi = vb2_get_drv_priv(vb->vb2_queue);
> > > struct imx7_csi_vb2_buffer *buf = to_imx7_csi_vb2_buffer(vb);
> > > unsigned long flags;
> > >
> > > + if (imx7_csi_fast_track_buffer(csi, buf))
> > > + return;
> > > +
> > > spin_lock_irqsave(&csi->q_lock, flags);
> > >
> > > list_add_tail(&buf->list, &csi->ready_q);

--
Regards,

Laurent Pinchart