Re: [PATCH 1/1] serial: 8250: Add helper for clearing IER
From: Andy Shevchenko
Date: Thu Aug 18 2022 - 03:19:03 EST
On Tue, Aug 16, 2022 at 3:14 PM Ilpo Järvinen
<ilpo.jarvinen@xxxxxxxxxxxxxxx> wrote:
>
> A number of places want to clear IER with the same CAP_UUE trick.
> Create a helper for that.
No objections,
Reviewed-by: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@xxxxxxxxxxxxxxx>
> ---
> drivers/tty/serial/8250/8250_port.c | 24 +++++++++++-------------
> 1 file changed, 11 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
> index 39b35a61958c..25e4761e3c57 100644
> --- a/drivers/tty/serial/8250/8250_port.c
> +++ b/drivers/tty/serial/8250/8250_port.c
> @@ -752,6 +752,14 @@ static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
> serial8250_rpm_put(p);
> }
>
> +static void serial8250_clear_IER(struct uart_8250_port *up)
> +{
> + if (up->capabilities & UART_CAP_UUE)
> + serial_out(up, UART_IER, UART_IER_UUE);
> + else
> + serial_out(up, UART_IER, 0);
> +}
> +
> #ifdef CONFIG_SERIAL_8250_RSA
> /*
> * Attempts to turn on the RSA FIFO. Returns zero on failure.
> @@ -1329,10 +1337,7 @@ static void autoconfig(struct uart_8250_port *up)
> serial8250_out_MCR(up, save_mcr);
> serial8250_clear_fifos(up);
> serial_in(up, UART_RX);
> - if (up->capabilities & UART_CAP_UUE)
> - serial_out(up, UART_IER, UART_IER_UUE);
> - else
> - serial_out(up, UART_IER, 0);
> + serial8250_clear_IER(up);
>
> out_unlock:
> spin_unlock_irqrestore(&port->lock, flags);
> @@ -2142,10 +2147,7 @@ static void serial8250_put_poll_char(struct uart_port *port,
> * First save the IER then disable the interrupts
> */
> ier = serial_port_in(port, UART_IER);
> - if (up->capabilities & UART_CAP_UUE)
> - serial_port_out(port, UART_IER, UART_IER_UUE);
> - else
> - serial_port_out(port, UART_IER, 0);
> + serial8250_clear_IER(up);
>
> wait_for_xmitr(up, UART_LSR_BOTH_EMPTY);
> /*
> @@ -3383,11 +3385,7 @@ void serial8250_console_write(struct uart_8250_port *up, const char *s,
> * First save the IER then disable the interrupts
> */
> ier = serial_port_in(port, UART_IER);
> -
> - if (up->capabilities & UART_CAP_UUE)
> - serial_port_out(port, UART_IER, UART_IER_UUE);
> - else
> - serial_port_out(port, UART_IER, 0);
> + serial8250_clear_IER(up);
>
> /* check scratch reg to see if port powered off during system sleep */
> if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) {
> --
> 2.30.2
>
--
With Best Regards,
Andy Shevchenko