Re: [PATCH v12 6/7] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

[Samuel Holland]

Hi Andre,

On 7/1/22 6:24 AM, Andre Przywara wrote:
> The OrangePi Zero 2 is a development board with the new H616 SoC. It
> comes with the following features:
>   - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
>   - 512MiB/1GiB DDR3 DRAM
>   - AXP305 PMIC
>   - Raspberry-Pi-1 compatible GPIO header
>   - extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
>   - 1 USB 2.0 host port
>   - 1 USB 2.0 type C port (power supply + OTG)
>   - MicroSD slot
>   - on-board 2MiB bootable SPI NOR flash
>   - 1Gbps Ethernet port (via RTL8211F PHY)
>   - micro-HDMI port
>   - (yet) unsupported Allwinner WiFi/BT chip
> 
> Add the devicetree file describing the currently supported features.
> 
> Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>

One question below.

> ---
>  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>  .../allwinner/sun50i-h616-orangepi-zero2.dts  | 213 ++++++++++++++++++
>  2 files changed, 214 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> 
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 8fa5c060a4fef..df2214e6d946a 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -38,3 +38,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> new file mode 100644
> index 0000000000000..cff199536d3bc
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> @@ -0,0 +1,213 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2020 Arm Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h616.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> +	model = "OrangePi Zero2";
> +	compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
> +
> +	aliases {
> +		ethernet0 = &emac0;
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		led-0 {
> +			function = LED_FUNCTION_POWER;
> +			color = <LED_COLOR_ID_RED>;
> +			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
> +			default-state = "on";
> +		};
> +
> +		led-1 {
> +			function = LED_FUNCTION_STATUS;
> +			color = <LED_COLOR_ID_GREEN>;
> +			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
> +		};
> +	};
> +
> +	reg_vcc5v: vcc5v {
> +		/* board wide 5V supply directly from the USB-C socket */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-5v";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +};
> +
> +&emac0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ext_rgmii_pins>;
> +	phy-mode = "rgmii";
> +	phy-handle = <&ext_rgmii_phy>;
> +	phy-supply = <&reg_dcdce>;
> +	allwinner,rx-delay-ps = <3100>;
> +	allwinner,tx-delay-ps = <700>;
> +	status = "okay";
> +};
> +
> +&mdio0 {
> +	ext_rgmii_phy: ethernet-phy@1 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <1>;
> +	};
> +};
> +
> +&mmc0 {
> +	vmmc-supply = <&reg_dcdce>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&r_rsb {
> +	status = "okay";
> +
> +	axp305: pmic@745 {
> +		compatible = "x-powers,axp305", "x-powers,axp805",
> +			     "x-powers,axp806";
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		reg = <0x745>;
> +
> +		x-powers,self-working-mode;
> +		vina-supply = <&reg_vcc5v>;
> +		vinb-supply = <&reg_vcc5v>;
> +		vinc-supply = <&reg_vcc5v>;
> +		vind-supply = <&reg_vcc5v>;
> +		vine-supply = <&reg_vcc5v>;
> +		aldoin-supply = <&reg_vcc5v>;
> +		bldoin-supply = <&reg_vcc5v>;
> +		cldoin-supply = <&reg_vcc5v>;
> +
> +		regulators {
> +			reg_aldo1: aldo1 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc-sys";
> +			};
> +
> +			reg_aldo2: aldo2 {	/* 3.3V on headers */
> +				regulator-always-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc3v3-ext";
> +			};
> +
> +			reg_aldo3: aldo3 {	/* 3.3V on headers */
> +				regulator-always-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc3v3-ext2";
> +			};
> +
> +			reg_bldo1: bldo1 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc1v8";
> +			};
> +
> +			bldo2 {
> +				/* unused */
> +			};
> +
> +			bldo3 {
> +				/* unused */
> +			};
> +
> +			bldo4 {
> +				/* unused */
> +			};
> +
> +			cldo1 {
> +				/* reserved */
> +			};
> +
> +			cldo2 {
> +				/* unused */
> +			};
> +
> +			cldo3 {
> +				/* unused */
> +			};
> +
> +			reg_dcdca: dcdca {
> +				regulator-always-on;
> +				regulator-min-microvolt = <810000>;
> +				regulator-max-microvolt = <1080000>;
> +				regulator-name = "vdd-cpu";
> +			};
> +
> +			reg_dcdcc: dcdcc {
> +				regulator-always-on;
> +				regulator-min-microvolt = <810000>;
> +				regulator-max-microvolt = <1080000>;

Where does the max voltage here come from? The H616 datasheet lists the limit
for both VDD_GPU and VDD_SYS as 0.99 V. (This applies to both boards.)

Regards,
Samuel

> +				regulator-name = "vdd-gpu-sys";
> +			};
> +
> +			reg_dcdcd: dcdcd {
> +				regulator-always-on;
> +				regulator-min-microvolt = <1500000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-name = "vdd-dram";
> +			};
> +
> +			reg_dcdce: dcdce {
> +				regulator-always-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc-eth-mmc";
> +			};
> +
> +			sw {
> +				/* unused */
> +			};
> +		};
> +	};
> +};
> +
> +&pio {
> +	vcc-pc-supply = <&reg_aldo1>;
> +	vcc-pf-supply = <&reg_aldo1>;
> +	vcc-pg-supply = <&reg_bldo1>;
> +	vcc-ph-supply = <&reg_aldo1>;
> +	vcc-pi-supply = <&reg_aldo1>;
> +};
> +
> +&spi0  {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
> +
> +	flash@0 {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +		spi-max-frequency = <40000000>;
> +	};
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_ph_pins>;
> +	status = "okay";
> +};
>