Re: [PATCH v17 4/5] usb: dwc3: qcom: Configure wakeup interrupts during suspend

[Matthias Kaehlcke]

On Tue, May 24, 2022 at 03:43:47PM +0530, Krishna Kurapati wrote:
> From: Sandeep Maheswaram <quic_c_sanm@xxxxxxxxxxx>
> 
> Configure DP/DM line interrupts based on the USB2 device attached to
> the root hub port. When HS/FS device is connected, configure the DP line
> as falling edge to detect both disconnect and remote wakeup scenarios. When
> LS device is connected, configure DM line as falling edge to detect both
> disconnect and remote wakeup. When no device is connected, configure both
> DP and DM lines as rising edge to detect HS/HS/LS device connect scenario.
> 
> Signed-off-by: Sandeep Maheswaram <quic_c_sanm@xxxxxxxxxxx>
> Reviewed-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>

With the addition of dwc3_qcom_update_usb2_speed() the patch has changed a
bit since my review, I'm generally on board with the direction this is going,
but please remove my R-B tag for now.

> Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx>
> ---
>  drivers/usb/dwc3/dwc3-qcom.c | 74 ++++++++++++++++++++++++++++++++++++++------
>  1 file changed, 65 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
> index 7352124..5d5db62 100644
> --- a/drivers/usb/dwc3/dwc3-qcom.c
> +++ b/drivers/usb/dwc3/dwc3-qcom.c
> @@ -20,7 +20,8 @@
>  #include <linux/usb/of.h>
>  #include <linux/reset.h>
>  #include <linux/iopoll.h>
> -
> +#include <linux/usb/hcd.h>
> +#include <linux/usb.h>
>  #include "core.h"
>  
>  /* USB QSCRATCH Hardware registers */
> @@ -296,11 +297,37 @@ static void dwc3_qcom_interconnect_exit(struct dwc3_qcom *qcom)
>  	icc_put(qcom->icc_path_apps);
>  }
>  
> -static void dwc3_qcom_enable_wakeup_irq(int irq)
> +enum usb_device_speed dwc3_qcom_update_usb2_speed(struct dwc3_qcom *qcom)
> +{
> +	struct dwc3	*dwc = platform_get_drvdata(qcom->dwc3);
> +	struct usb_hcd	*hcd = platform_get_drvdata(dwc->xhci);
> +	struct usb_device *udev;
> +	enum usb_device_speed usb2_speed;

nit: dwc and hcd are indented to align, udev and usb2_speed not. Either align
the indentation or not, but don't be inconsistent. My vote goes for removing
the alignment.

> +
> +	/*
> +	 * It is possible to query the speed of all children of
> +	 * USB2.0 root hub via usb_hub_for_each_child(). DWC3 code
> +	 * currently supports only 1 port per controller. So
> +	 * this is sufficient.
> +	 */
> +	udev = usb_hub_find_child(hcd->self.root_hub, 1);
> +
> +	if (udev)
> +		usb2_speed = udev->speed;
> +	else
> +		usb2_speed = USB_SPEED_UNKNOWN;
> +
> +	return usb2_speed;

nit: you could get away without 'usb2_speed':

	if (!udev)
		return USB_SPEED_UNKNOWN;

	return udev->speed;