Re: [PATCH v4 2/3] dt-bindings: remoteproc: qcom: Convert SC7280 MSS bindings to YAML

[Stephen Boyd]

Quoting Sibi Sankar (2022-05-19 09:47:04)
> diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
> new file mode 100644
> index 000000000000..a936d84eefa6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
> @@ -0,0 +1,250 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/remoteproc/qcom,sc7280-mss-pil.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm SC7280 MSS Peripheral Image Loader
> +
> +maintainers:
> +  - Sibi Sankar <quic_sibis@xxxxxxxxxxx>
> +
> +description:
> +  This document describes the hardware for a component that loads and boots firmware
> +  on the Qualcomm Technology Inc. SC7280 Modem Hexagon Core.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - qcom,sc7280-mss-pil
> +
[..]
> +
> +  resets:
> +    items:
> +      - description: AOSS restart
> +      - description: PDC reset
> +
> +  reset-names:
> +    items:
> +      - const: mss_restart
> +      - const: pdc_reset
> +
> +  memory-region:
> +    maxItems: 2
> +    description: Phandle reference to the reserved-memory for the MBA region followed
> +                 by the modem region.
> +
> +  firmware-name:
> +    $ref: /schemas/types.yaml#/definitions/string-array
> +    maxItems: 2

Instead of maxItems can this be

       items:
         - description: Name of MBA firmware
	 - description: Name of modem firmware

so that we know the order? Same for 'memory-region' above.

> +    description:
> +      The name of the MBA and modem firmware to be loaded for this remote processor.
> +
> +  qcom,halt-regs:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array

Should this have maxItems: 1? Or that's implicit from description?

> +    description:
> +      Phandle reference to a syscon representing TCSR followed by the
> +      four offsets within syscon for q6, modem, nc and vq6 halt registers.
> +
> +  qcom,ext-regs:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array

Should this have min/maxItems: 2?

> +    description:
> +      Two phandle references to syscons representing TCSR_REG and TCSR register
> +      space followed by the two offsets within the syscon to force_clk_en/rscc_disable
> +      and axim1_clk_off/crypto_clk_off registers respectively.
> +
> +  qcom,qaccept-regs:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> +    description:
> +      Phandle reference to a syscon representing TCSR followed by the
> +      three offsets within syscon for mdm, cx and axi qaccept registers.
> +
> +  qcom,qmp:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description: Reference to the AOSS side-channel message RAM.
> +
> +  qcom,smem-states:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> +    description: States used by the AP to signal the Hexagon core
> +    items:
> +      - description: Stop the modem

This one did items for a phandle array so I think we should follow the
same above.

> +
> +  qcom,smem-state-names:
> +    description: The names of the state bits used for SMP2P output
> +    const: stop
> +
> +  glink-edge:
> +    $ref: qcom,glink-edge.yaml#
> +    description:
> +      Qualcomm G-Link subnode which represents communication edge, channels
> +      and devices related to the DSP.
[..]
> +        power-domain-names = "cx", "mss";
> +
> +        memory-region = <&mba_mem>, <&mpss_mem>;
> +
> +        qcom,qmp = <&aoss_qmp>;
> +
> +        qcom,smem-states = <&modem_smp2p_out 0>;
> +        qcom,smem-state-names = "stop";
> +
> +        resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
> +                 <&pdc_reset PDC_MODEM_SYNC_RESET>;
> +        reset-names = "mss_restart", "pdc_reset";
> +
> +        qcom,halt-regs = <&tcsr_mutex 0x23000 0x25000 0x28000 0x33000>;
> +        qcom,ext-regs = <&tcsr 0x10000 0x10004 &tcsr_mutex 0x26004 0x26008>;

Because it's two items I'd expect:
	
	<&tcsr 0x10000 0x10004>, <&tcsr_mutex 0x26004 0x26008>;

> +        qcom,qaccept-regs = <&tcsr_mutex 0x23030 0x23040 0x23020>;
> +
> +        glink-edge {
> +            interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
> +                                   IPCC_MPROC_SIGNAL_GLINK_QMP
> +                                   IRQ_TYPE_EDGE_RISING>;