Re: [v16 2/5] usb: dwc3: core: Host wake up support from system suspend

From: Matthias Kaehlcke
Date: Mon May 16 2022 - 19:13:53 EST

Next message: Andrii Nakryiko: "Re: [PATCH v3] bpf: Fix KASAN use-after-free Read in compute_effective_progs"
Previous message: Jason Gunthorpe: "Re: [PATCH v7 17/22] vfio-pci/zdev: add open/close device hooks"
In reply to: Pavan Kondeti: "Re: [v16 2/5] usb: dwc3: core: Host wake up support from system suspend"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Mon, May 16, 2022 at 08:34:45PM +0530, Pavan Kondeti wrote:
> On Mon, May 16, 2022 at 10:13:27AM +0530, Pavan Kondeti wrote:
> > On Fri, May 13, 2022 at 09:28:16AM +0530, Krishna Kurapati PSSNV wrote:
> > >
> > > On 5/13/2022 4:10 AM, Matthias Kaehlcke wrote:
> > > >On Thu, May 12, 2022 at 11:53:19PM +0530, Krishna Kurapati wrote:
> > > >>From: Sandeep Maheswaram <quic_c_sanm@xxxxxxxxxxx>
> > > >>
> > > >>During suspend read the status of all port and set hs phy mode
> > > >>based on current speed. Use this hs phy mode to configure wakeup
> > > >>interrupts in qcom glue driver.
> > > >>
> > > >>Check wakeup-source property for dwc3 core node to set the
> > > >>wakeup capability. Drop the device_init_wakeup call from
> > > >>runtime suspend and resume.
> > > >>
> > > >>Also check during suspend if any wakeup capable devices are
> > > >>connected to the controller (directly or through hubs), if there
> > > >>are none set a flag to indicate that the PHY is powered
> > > >>down during suspend.
> > > >>
> > > >>Signed-off-by: Sandeep Maheswaram <quic_c_sanm@xxxxxxxxxxx>
> > > >>Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx>
> > > >>---
> > > >> drivers/usb/dwc3/core.c | 30 +++++++++++++++++-------------
> > > >> drivers/usb/dwc3/core.h | 4 ++++
> > > >> drivers/usb/dwc3/host.c | 24 ++++++++++++++++++++++++
> > > >> 3 files changed, 45 insertions(+), 13 deletions(-)
> > > >>
> > > >>diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> > > >>index 01115df..8bcabc5 100644
> > > >>--- a/drivers/usb/dwc3/core.c
> > > >>+++ b/drivers/usb/dwc3/core.c
> > > >>@@ -1785,6 +1785,7 @@ static int dwc3_probe(struct platform_device *pdev)
> > > >> platform_set_drvdata(pdev, dwc);
> > > >> dwc3_cache_hwparams(dwc);
> > > >>+ device_init_wakeup(&pdev->dev, of_property_read_bool(dev->of_node, "wakeup-source"));
> > > >> spin_lock_init(&dwc->lock);
> > > >> mutex_init(&dwc->mutex);
> > > >>@@ -1946,10 +1947,7 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
> > > >> dwc3_core_exit(dwc);
> > > >> break;
> > > >> case DWC3_GCTL_PRTCAP_HOST:
> > > >>- if (!PMSG_IS_AUTO(msg)) {
> > > >>- dwc3_core_exit(dwc);
> > > >>- break;
> > > >>- }
> > > >>+ dwc3_check_phy_speed_mode(dwc);
> > > >> /* Let controller to suspend HSPHY before PHY driver suspends */
> > > >> if (dwc->dis_u2_susphy_quirk ||
> > > >>@@ -1965,6 +1963,15 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
> > > >> phy_pm_runtime_put_sync(dwc->usb2_generic_phy);
> > > >> phy_pm_runtime_put_sync(dwc->usb3_generic_phy);
> > > >>+
> > > >>+ if (!PMSG_IS_AUTO(msg)) {
> > > >>+ if (device_may_wakeup(dwc->dev))
> > > >I think this should be device_can_wakeup(), i.e. hardware capability instead of
> > > >device policy. A drawback of powering the PHYs off is that it causes a high
> > > >power consumption of certain peripherals if VBUS is still supplied, so this
> > > >should be limited to platforms where the PHYs must be powered off (using wakeup
> > > >capability as a proxy for now).
> > > Thnaks Mathias for the review. Will make this change in the next patchset.
> > > >>+ dwc->phy_power_off = false;
> > > >>+ else {
> > > >>+ dwc->phy_power_off = true;
> > > >>+ dwc3_core_exit(dwc);
> > > >>+ }
> > > >>+ }
> > > >> break;
> > > >> case DWC3_GCTL_PRTCAP_OTG:
> > > >> /* do nothing during runtime_suspend */
> > > >>@@ -2008,11 +2015,12 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg)
> > > >> break;
> > > >> case DWC3_GCTL_PRTCAP_HOST:
> > > >> if (!PMSG_IS_AUTO(msg)) {
> > > >>- ret = dwc3_core_init_for_resume(dwc);
> > > >>- if (ret)
> > > >>- return ret;
> > > >>- dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
> > > >>- break;
> > > >>+ if (dwc->phy_power_off) {
> > > >>+ ret = dwc3_core_init_for_resume(dwc);
> > > >>+ if (ret)
> > > >>+ return ret;
> > > >>+ dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
> > > >>+ }
> > > >> }
> > > >> /* Restore GUSB2PHYCFG bits that were modified in suspend */
> > > >> reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
> > > >>@@ -2084,8 +2092,6 @@ static int dwc3_runtime_suspend(struct device *dev)
> > > >> if (ret)
> > > >> return ret;
> > > >>- device_init_wakeup(dev, true);
> > > >>-
> > > >> return 0;
> > > >> }
> > > >>@@ -2094,8 +2100,6 @@ static int dwc3_runtime_resume(struct device *dev)
> > > >> struct dwc3 *dwc = dev_get_drvdata(dev);
> > > >> int ret;
> > > >>- device_init_wakeup(dev, false);
> > > >>-
> > > >> ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME);
> > > >> if (ret)
> > > >> return ret;
> > > >>diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
> > > >>index 81c486b..37397a8 100644
> > > >>--- a/drivers/usb/dwc3/core.h
> > > >>+++ b/drivers/usb/dwc3/core.h
> > > >>@@ -1155,6 +1155,9 @@ struct dwc3 {
> > > >> bool phys_ready;
> > > >>+ unsigned int hs_phy_mode;
> > > >>+ bool phy_power_off;
> > > >>+
> > > >> struct ulpi *ulpi;
> > > >> bool ulpi_ready;
> > > >>@@ -1539,6 +1542,7 @@ int dwc3_core_soft_reset(struct dwc3 *dwc);
> > > >> #if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
> > > >> int dwc3_host_init(struct dwc3 *dwc);
> > > >> void dwc3_host_exit(struct dwc3 *dwc);
> > > >>+void dwc3_check_phy_speed_mode(struct dwc3 *dwc);
> > > >> #else
> > > >> static inline int dwc3_host_init(struct dwc3 *dwc)
> > > >> { return 0; }
> > > >>diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c
> > > >>index f56c30c..e19b40a 100644
> > > >>--- a/drivers/usb/dwc3/host.c
> > > >>+++ b/drivers/usb/dwc3/host.c
> > > >>@@ -12,6 +12,7 @@
> > > >> #include <linux/platform_device.h>
> > > >> #include "core.h"
> > > >>+#include "../host/xhci.h"
> > > >> static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc,
> > > >> int irq, char *name)
> > > >>@@ -136,3 +137,26 @@ void dwc3_host_exit(struct dwc3 *dwc)
> > > >> {
> > > >> platform_device_unregister(dwc->xhci);
> > > >> }
> > > >>+
> > > >>+void dwc3_check_phy_speed_mode(struct dwc3 *dwc)
> > > >>+{
> > > >>+ int i, num_ports;
> > > >>+ u32 reg;
> > > >>+ struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci);
> > > >>+ struct xhci_hcd *xhci_hcd = hcd_to_xhci(hcd);
> > > >>+
> > > >>+ dwc->hs_phy_mode = 0;
> > > >>+
> > > >>+ reg = readl(&xhci_hcd->cap_regs->hcs_params1);
> > > >>+
> > > >>+ num_ports = HCS_MAX_PORTS(reg);
> > > >>+ for (i = 0; i < num_ports; i++) {
> > > >>+ reg = readl(&xhci_hcd->op_regs->port_status_base + i * NUM_PORT_REGS);
> > > >>+ if (reg & PORT_PE) {
> > > >>+ if (DEV_HIGHSPEED(reg) || DEV_FULLSPEED(reg))
> > > >>+ dwc->hs_phy_mode |= PHY_MODE_USB_HOST_HS;
> > > >>+ else if (DEV_LOWSPEED(reg))
> > > >>+ dwc->hs_phy_mode |= PHY_MODE_USB_HOST_LS;
> > > >>+ }
> > > >>+ }
> > > >>+}
> > > >I anticipate that it might raise concerns from maintainers that
> > > >dwc3_check_phy_speed_mode() accesses xHCI data structures and
> > > >registers directly. Could there be a generic HCD API that provides
> > > >this functionality (if implemented by the specific HCD)?
> > >
> > > Hi Mathias, we are not sure if there is any such API present currently.
> > >
> > > Hi Alan, can you help suggest any API (if present) that we can reuse here to
> > > avoid
> > >
> > > xhci registers and structs here in dwc3.
> > >
> >
> > We can probably do something like below to query the speed. This avoids adding
> > another API and does not touch the underlying registers.
> >
> > Pls define enum usb_device_speed usb2_speed in dwc3 structure.
> >
> > diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c
> > index f29a264..fed1c58 100644
> > --- a/drivers/usb/dwc3/host.c
> > +++ b/drivers/usb/dwc3/host.c
> > @@ -9,9 +9,29 @@
> >
> > #include <linux/acpi.h>
> > #include <linux/platform_device.h>
> > +#include <linux/usb.h>
> >
> > #include "core.h"
> >
> > +void dwc3_update_hs_phy_speed(struct dwc3 *dwc)
> > +{
> > + struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci);
> > + struct usb_device *udev;
> > +
> > + /*
> > + * It is possible to query the speed of all children of
> > + * USB2.0 root hub via usb_hub_for_each_child(). DWC3 code
> > + * currently supports only 1 port per controller. So
> > + * this is sufficient.
> > + */
> > + udev = usb_hub_find_child(hcd->self.root_hub, 1);
> > +
> > + if (udev)
> > + dwc->usb2_speed = udev->speed;
> > + else
> > + dwc->usb2_speed = USB_SPEED_UNKNOWN;
> > +}
> > +
> > static int dwc3_host_get_irq(struct dwc3 *dwc)
> > {
> > struct platform_device *dwc3_pdev = to_platform_device(dwc->dev);
> >
> >
> I am also thinking why dwc core needs to cache usb2_speed since dwc3-qcom glue
> driver is the only sole user. We also require it only during suspend and does
> not bother about dwc::usb2_speed correctness outside suspend. Lets move this
> to dwc3-qcom suspend routines where we have to rely on USB2 speed for
> configuring the D+/D- interrupt.

I like both of your suggestions. If something like dwc3_update_hs_phy_speed()
works properly here we should have finally sorted out all the layering issues
Felipe was unhappy about.

Next message: Andrii Nakryiko: "Re: [PATCH v3] bpf: Fix KASAN use-after-free Read in compute_effective_progs"
Previous message: Jason Gunthorpe: "Re: [PATCH v7 17/22] vfio-pci/zdev: add open/close device hooks"
In reply to: Pavan Kondeti: "Re: [v16 2/5] usb: dwc3: core: Host wake up support from system suspend"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]