[PATCH 2/2] rtc: Introduce ti-k3-rtc

From: Nishanth Menon
Date: Tue Apr 12 2022 - 05:28:58 EST


Introduce support for Texas Instruments Real Time Clock controller on
newer K3 family of SoCs such as AM62x.

The hardware module that is being supported is the "digital only"
version which does'nt have capability of external wakeup sources and
external power backup. However, for many practical applications, this
should suffice as RTC is operational across low power sequences.

The hardware block by itself is split into two distinct domains
internally to further reduce the power consumption with the actual
counter block and comparators clocked off a 32k clock source (which
based on SoC integration can be sourced by an external crystal) and an
register interface block which is driven by the bus clock. While optimal
from power perspective, it does create some complicated synchronizations
and sequences that one must be wary of in the driver handling.

Signed-off-by: Nishanth Menon <nm@xxxxxx>
---
drivers/rtc/Kconfig | 10 +
drivers/rtc/Makefile | 1 +
drivers/rtc/rtc-ti-k3.c | 687 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 698 insertions(+)
create mode 100644 drivers/rtc/rtc-ti-k3.c

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 41c65b4d2baf..972602af8838 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1922,6 +1922,16 @@ config RTC_DRV_ASPEED
This driver can also be built as a module, if so, the module
will be called "rtc-aspeed".

+config RTC_DRV_TI_K3
+ tristate "TI K3 RTC"
+ depends on ARCH_K3 || COMPILE_TEST
+ help
+ If you say yes here you get support for the Texas Instruments's
+ Real Time Clock for K3 architecture.
+
+ This driver can also be built as a module, if so, the module
+ will be called "rtc-ti-k3".
+
comment "HID Sensor RTC drivers"

config RTC_DRV_HID_SENSOR_TIME
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index 2d827d8261d5..b74128e174d7 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -183,3 +183,4 @@ obj-$(CONFIG_RTC_DRV_WM8350) += rtc-wm8350.o
obj-$(CONFIG_RTC_DRV_X1205) += rtc-x1205.o
obj-$(CONFIG_RTC_DRV_XGENE) += rtc-xgene.o
obj-$(CONFIG_RTC_DRV_ZYNQMP) += rtc-zynqmp.o
+obj-$(CONFIG_RTC_DRV_TI_K3) += rtc-ti-k3.o
diff --git a/drivers/rtc/rtc-ti-k3.c b/drivers/rtc/rtc-ti-k3.c
new file mode 100644
index 000000000000..7220f0f12071
--- /dev/null
+++ b/drivers/rtc/rtc-ti-k3.c
@@ -0,0 +1,687 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Texas Instruments K3 RTC driver
+ *
+ * Copyright (C) 2021-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#define dev_fmt(fmt) "%s: " fmt, __func__
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/rtc.h>
+
+/* Registers */
+#define REG_K3RTC_S_CNT_LSW 0x08
+#define REG_K3RTC_S_CNT_MSW 0x0c
+#define REG_K3RTC_COMP 0x10
+#define REG_K3RTC_ON_OFF_S_CNT_LSW 0x20
+#define REG_K3RTC_ON_OFF_S_CNT_MSW 0x24
+#define REG_K3RTC_SCRATCH0 0x30
+#define REG_K3RTC_SCRATCH7 0x4c
+#define REG_K3RTC_GENERAL_CTL 0x50
+#define REG_K3RTC_IRQSTATUS_RAW_SYS 0x54
+#define REG_K3RTC_IRQSTATUS_SYS 0x58
+#define REG_K3RTC_IRQENABLE_SET_SYS 0x5c
+#define REG_K3RTC_IRQENABLE_CLR_SYS 0x60
+#define REG_K3RTC_SYNCPEND 0x68
+#define REG_K3RTC_KICK0 0x70
+#define REG_K3RTC_KICK1 0x74
+
+/* Control Bits for REG_K3RTC_S_CNT_LSW */
+#define K3RTC_S_CNT_LSW_MASK GENMASK(31, 0)
+
+/* Control Bits for REG_K3RTC_S_CNT_MSW */
+#define K3RTC_S_CNT_MSW_MASK GENMASK(15, 0)
+
+/* Control Bits for REG_K3RTC_GENERAL_CTL */
+#define K3RTC_O32K_OSC_DEP_EN_BIT BIT(21)
+#define K3RTC_UNLOCK_BIT BIT(23)
+#define K3RTC_CNT_FMODE_MASK GENMASK(25, 24)
+#define K3RTC_CNT_FMODE_S_CNT_VALUE (0x2 << 24)
+
+/* Control Bits for REG_K3RTC_IRQ* */
+#define K3RTC_EVENT_ON_OFF_BIT BIT(0)
+#define K3RTC_EVENT_OFF_ON_BIT BIT(1)
+
+/* Control Bits for REG_K3RTC_SYNCPEND */
+#define K3RTC_WR_PEND_BIT BIT(0)
+#define K3RTC_RD_PEND_BIT BIT(1)
+#define K3RTC_RELOAD_FROM_BBD_BIT BIT(31)
+
+/* Magic values for lock/unlock */
+#define K3RTC_KICK0_UNLOCK_VALUE 0x83e70b13
+#define K3RTC_KICK1_UNLOCK_VALUE 0x95a4f1e0
+
+/* Multiplier for ppb conversions */
+#define K3RTC_PPB_MULT (1000000000LL)
+/* Min and max values supported with 'offset' interface (swapped sign) */
+#define K3RTC_MIN_OFFSET (-277761)
+#define K3RTC_MAX_OFFSET (277778)
+
+/**
+ * struct ti_k3_rtc_soc_data - Private of compatible data for ti-k3-rtc
+ * @unlock_irq_erratum: Has erratum for unlock infinite IRQs (erratum i2327)
+ */
+struct ti_k3_rtc_soc_data {
+ const bool unlock_irq_erratum;
+};
+
+/**
+ * struct ti_k3_rtc - Private data for ti-k3-rtc
+ * @irq: IRQ
+ * @sync_timeout_us: data sync timeout period in uSec (2 * 32k period)
+ * @rate_32k: 32k clock rate in Hz
+ * @rtc_dev: rtc device
+ * @rtc_base: rtc base address
+ * @soc: SoC compatible match data
+ */
+struct ti_k3_rtc {
+ unsigned int irq;
+ u32 sync_timeout_us;
+ unsigned long rate_32k;
+ struct rtc_device *rtc_dev;
+ void __iomem *rtc_base;
+ const struct ti_k3_rtc_soc_data *soc;
+};
+
+static inline u32 k3rtc_readl(struct ti_k3_rtc *priv, u32 offset)
+{
+ return readl(priv->rtc_base + offset);
+}
+
+static inline void k3rtc_writel(struct ti_k3_rtc *priv, u32 offset, u32 value)
+{
+ writel(value, priv->rtc_base + offset);
+}
+
+/**
+ * k3rtc_fence - Ensure a register sync took place between the two domains
+ * @priv: pointer to priv data
+ *
+ * Return: 0 if the sync took place, else returns -ETIMEDOUT
+ */
+static int k3rtc_fence(struct ti_k3_rtc *priv)
+{
+ u32 timeout = priv->sync_timeout_us;
+ u32 mask = K3RTC_RD_PEND_BIT | K3RTC_WR_PEND_BIT;
+ u32 val = 0;
+
+ while (timeout--) {
+ val = k3rtc_readl(priv, REG_K3RTC_SYNCPEND);
+ if (!(val & mask))
+ return 0;
+ usleep_range(1, 2);
+ }
+
+ pr_err("RTC Fence timeout: 0x%08x\n", val);
+ return -ETIMEDOUT;
+}
+
+static inline int k3rtc_check_unlocked(struct ti_k3_rtc *priv)
+{
+ u32 val;
+
+ val = k3rtc_readl(priv, REG_K3RTC_GENERAL_CTL);
+ return (val & K3RTC_UNLOCK_BIT) ? 0 : 1;
+}
+
+static int k3rtc_unlock_rtc(struct ti_k3_rtc *priv)
+{
+ u32 timeout = priv->sync_timeout_us;
+ int ret;
+
+ ret = k3rtc_check_unlocked(priv);
+ if (!ret)
+ return ret;
+
+ k3rtc_writel(priv, REG_K3RTC_KICK0, K3RTC_KICK0_UNLOCK_VALUE);
+ k3rtc_writel(priv, REG_K3RTC_KICK1, K3RTC_KICK1_UNLOCK_VALUE);
+
+ /* Skip fence since we are going to check the unlock bit as fence */
+ while (timeout--) {
+ ret = k3rtc_check_unlocked(priv);
+ if (!ret)
+ return ret;
+ usleep_range(1, 2);
+ }
+
+ return -ETIMEDOUT;
+}
+
+static int k3rtc_configure(struct device *dev)
+{
+ int ret;
+ u32 ctl;
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+
+ /*
+ * HWBUG: The compare statemachine is broken if the RTC module
+ * is NOT unlocked in under one second of boot - which is pretty long
+ * time from the perspective of Linux driver (module load, u-boot
+ * shell all can take much longer than this.
+ *
+ * In such occurrence, it is assumed that the RTC module is un-usable
+ */
+ if (priv->soc->unlock_irq_erratum) {
+ ret = k3rtc_check_unlocked(priv);
+ /* If there is an error OR if we are locked, return error */
+ if (ret) {
+ dev_err(dev, HW_ERR "Erratum i2327 unlock QUIRK! Cannot operate!!\n");
+ return -EFAULT;
+ }
+ } else {
+ /* May Need to explicitly unlock first time */
+ ret = k3rtc_unlock_rtc(priv);
+ if (ret) {
+ dev_err(dev, "Failed to unlock(%d)!\n", ret);
+ return ret;
+ }
+ }
+
+ /* Enable Shadow register sync on 32k clk boundary */
+ ctl = k3rtc_readl(priv, REG_K3RTC_GENERAL_CTL);
+ ctl |= K3RTC_O32K_OSC_DEP_EN_BIT;
+ k3rtc_writel(priv, REG_K3RTC_GENERAL_CTL, ctl);
+
+ /*
+ * Wait at least 2 clk sync time before proceeding further programming.
+ * This ensures that the 32k based sync is active.
+ */
+ usleep_range(priv->sync_timeout_us, priv->sync_timeout_us + 5);
+
+ /* We need to ensure fence here to make sure sync here */
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev, "Failed fence osc_dep enable(%d) - is 32k clk working?!\n",
+ ret);
+ return ret;
+ }
+
+ /* Lets just make sure we get consistent time value */
+ ctl &= ~K3RTC_CNT_FMODE_MASK;
+ /*
+ * FMODE setting: Reading lower seconds will freeze value on higher
+ * seconds. This also implies that we must *ALWAYS* read lower seconds
+ * prior to reading higher seconds
+ */
+ ctl |= K3RTC_CNT_FMODE_S_CNT_VALUE;
+ k3rtc_writel(priv, REG_K3RTC_GENERAL_CTL, ctl);
+
+ /* Clear any spurious IRQ sources if any */
+ k3rtc_writel(priv, REG_K3RTC_IRQSTATUS_SYS,
+ K3RTC_EVENT_ON_OFF_BIT | K3RTC_EVENT_OFF_ON_BIT);
+ /* Disable all IRQs */
+ k3rtc_writel(priv, REG_K3RTC_IRQENABLE_CLR_SYS,
+ K3RTC_EVENT_ON_OFF_BIT | K3RTC_EVENT_OFF_ON_BIT);
+
+ /* And.. Let us Sync the writes in */
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev, "Failed to fence(%d)!\n", ret);
+ return ret;
+ }
+
+ return ret;
+}
+
+static int ti_k3_rtc_read_time(struct device *dev, struct rtc_time *tm)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 seconds_lo, seconds_hi;
+
+ seconds_lo = k3rtc_readl(priv, REG_K3RTC_S_CNT_LSW);
+ seconds_hi = k3rtc_readl(priv, REG_K3RTC_S_CNT_MSW);
+
+ rtc_time64_to_tm((((time64_t)seconds_hi) << 32) | (time64_t)seconds_lo, tm);
+
+ return 0;
+}
+
+static int ti_k3_rtc_set_time(struct device *dev, struct rtc_time *tm)
+{
+ int ret;
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ time64_t seconds;
+ u32 seconds_lo, seconds_hi;
+
+ seconds = rtc_tm_to_time64(tm);
+
+ seconds_lo = seconds & K3RTC_S_CNT_LSW_MASK;
+ seconds_hi = (seconds >> 32) & K3RTC_S_CNT_MSW_MASK;
+
+ k3rtc_writel(priv, REG_K3RTC_S_CNT_LSW, seconds_lo);
+ k3rtc_writel(priv, REG_K3RTC_S_CNT_MSW, seconds_hi);
+
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev, "Failed to fence(%d)!\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int ti_k3_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alarm)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 seconds_lo, seconds_hi;
+ u32 alm;
+
+ seconds_lo = k3rtc_readl(priv, REG_K3RTC_ON_OFF_S_CNT_LSW);
+ seconds_hi = k3rtc_readl(priv, REG_K3RTC_ON_OFF_S_CNT_MSW);
+
+ rtc_time64_to_tm((((time64_t)seconds_hi) << 32) | (time64_t)seconds_lo, &alarm->time);
+
+ alm = k3rtc_readl(priv, REG_K3RTC_IRQENABLE_SET_SYS);
+ alarm->enabled = (alm & K3RTC_EVENT_ON_OFF_BIT) ? 1 : 0;
+
+ return 0;
+}
+
+static int ti_k3_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled)
+{
+ int ret;
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 reg;
+ u32 offset =
+ enabled ? REG_K3RTC_IRQENABLE_SET_SYS : REG_K3RTC_IRQENABLE_CLR_SYS;
+
+ reg = k3rtc_readl(priv, REG_K3RTC_IRQENABLE_SET_SYS);
+ reg &= K3RTC_EVENT_ON_OFF_BIT;
+ if ((enabled && reg) || (!enabled && !reg))
+ return 0;
+
+ k3rtc_writel(priv, offset, K3RTC_EVENT_ON_OFF_BIT);
+
+ /*
+ * Ensure the write sync is through - NOTE: it should be OK to have
+ * ISR to fire as we are checking sync (which should be done in a 32k
+ * cycle or so).
+ */
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev, "Failed to fence(%d)!\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int ti_k3_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alarm)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ time64_t seconds;
+ u32 seconds_lo, seconds_hi;
+ int ret;
+
+ seconds = rtc_tm_to_time64(&alarm->time);
+
+ seconds_lo = seconds & K3RTC_S_CNT_LSW_MASK;
+ seconds_hi = (seconds >> 32) & K3RTC_S_CNT_MSW_MASK;
+
+ k3rtc_writel(priv, REG_K3RTC_ON_OFF_S_CNT_LSW, seconds_lo);
+ k3rtc_writel(priv, REG_K3RTC_ON_OFF_S_CNT_MSW, seconds_hi);
+
+ /* Make sure the alarm time is synced in */
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev, "Failed to fence(%d)!\n", ret);
+ return ret;
+ }
+
+ /* Alarm irq enable will do a sync */
+ return ti_k3_rtc_alarm_irq_enable(dev, alarm->enabled);
+}
+
+static int ti_k3_rtc_read_offset(struct device *dev, long *offset)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 ticks_per_hr = priv->rate_32k * 3600;
+ int comp;
+ s64 tmp;
+
+ comp = k3rtc_readl(priv, REG_K3RTC_COMP);
+
+ /* Convert from RTC calibration register format to ppb format */
+ tmp = comp * (s64)K3RTC_PPB_MULT;
+ if (tmp < 0)
+ tmp -= ticks_per_hr / 2LL;
+ else
+ tmp += ticks_per_hr / 2LL;
+ tmp = div_s64(tmp, ticks_per_hr);
+
+ /* Offset value operates in negative way, so swap sign */
+ *offset = (long)-tmp;
+
+ return 0;
+}
+
+static int ti_k3_rtc_set_offset(struct device *dev, long offset)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 ticks_per_hr = priv->rate_32k * 3600;
+ int comp;
+ s64 tmp;
+
+ /* Make sure offset value is within supported range */
+ if (offset < K3RTC_MIN_OFFSET || offset > K3RTC_MAX_OFFSET)
+ return -ERANGE;
+
+ /* Convert from ppb format to RTC calibration register format */
+ tmp = offset * (s64)ticks_per_hr;
+ if (tmp < 0)
+ tmp -= K3RTC_PPB_MULT / 2LL;
+ else
+ tmp += K3RTC_PPB_MULT / 2LL;
+ tmp = div_s64(tmp, K3RTC_PPB_MULT);
+
+ /* Offset value operates in negative way, so swap sign */
+ comp = (int)-tmp;
+
+ k3rtc_writel(priv, REG_K3RTC_COMP, comp);
+
+ return k3rtc_fence(priv);
+}
+
+static irqreturn_t ti_k3_rtc_interrupt(s32 irq, void *dev_id)
+{
+ struct device *dev = dev_id;
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 reg;
+ u32 timeout;
+ int ret;
+
+ /*
+ * IRQ assertion can be very fast, however, the IRQ Status clear
+ * de-assert depends on 32k clock edge in the 32k domain
+ * If we clear the status prior to the first 32k clock edge,
+ * the status bit is cleared, but the IRQ is stays re-asserted.
+ *
+ * To prevent this condition, we need to wait for one 32k clock cycle
+ * We can either do that by polling the 32k observability signal for
+ * a toggle OR we could just sleep and let the processor do other
+ * stuff. We use sync_timeout_us which is 2x32k clock period to
+ * make sure.
+ */
+ usleep_range(priv->sync_timeout_us, priv->sync_timeout_us + 2);
+
+ /* Lets make sure that this is a valid interrupt */
+ reg = k3rtc_readl(priv, REG_K3RTC_IRQSTATUS_SYS);
+
+ if (!(reg & K3RTC_EVENT_ON_OFF_BIT)) {
+ u32 raw = k3rtc_readl(priv, REG_K3RTC_IRQSTATUS_RAW_SYS);
+
+ dev_err(dev, HW_ERR "Erratum i2327 / false interrupt? IRQ status: 0x%08x / 0x%08x\n",
+ reg, raw);
+ return IRQ_NONE;
+ }
+
+ /* Write 1 to clear status reg */
+ k3rtc_writel(priv, REG_K3RTC_IRQSTATUS_SYS, K3RTC_EVENT_ON_OFF_BIT);
+
+ /* Sync the write in */
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev, "Failed to fence irq status clr(%d)!\n", ret);
+ return IRQ_NONE;
+ }
+
+ /*
+ * Force the 32k status to be reloaded back in to ensure status is
+ * reflected back correctly.
+ */
+ reg = k3rtc_readl(priv, REG_K3RTC_SYNCPEND);
+ if (ret) {
+ dev_err(dev, "sync read fail:%d\n", ret);
+ return IRQ_NONE;
+ }
+ reg |= K3RTC_RELOAD_FROM_BBD_BIT;
+ k3rtc_writel(priv, REG_K3RTC_SYNCPEND, reg);
+
+ /* Ensure the write sync is through */
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev, "Failed to fence reload from bbd(%d)!\n", ret);
+ return IRQ_NONE;
+ }
+
+ /* Now we ensure that the status bit is cleared */
+ timeout = priv->sync_timeout_us;
+ while (timeout--) {
+ reg = k3rtc_readl(priv, REG_K3RTC_IRQSTATUS_SYS);
+ if (!(reg & K3RTC_EVENT_ON_OFF_BIT))
+ break;
+
+ usleep_range(1, 2);
+ }
+ if (!timeout) {
+ dev_err(dev, "Time out waiting for status clear: 0x%08x\n", reg);
+ return IRQ_NONE;
+ }
+
+ /* Notify RTC core on event */
+ rtc_update_irq(priv->rtc_dev, 1, RTC_IRQF | RTC_AF);
+
+ return IRQ_HANDLED;
+}
+
+static const struct rtc_class_ops ti_k3_rtc_ops = {
+ .read_time = ti_k3_rtc_read_time,
+ .set_time = ti_k3_rtc_set_time,
+ .read_alarm = ti_k3_rtc_read_alarm,
+ .set_alarm = ti_k3_rtc_set_alarm,
+ .read_offset = ti_k3_rtc_read_offset,
+ .set_offset = ti_k3_rtc_set_offset,
+ .alarm_irq_enable = ti_k3_rtc_alarm_irq_enable,
+};
+
+static int ti_k3_rtc_scratch_read(void *priv_data, unsigned int offset,
+ void *_val, size_t bytes)
+{
+ struct ti_k3_rtc *priv = (struct ti_k3_rtc *)priv_data;
+ u32 *val = _val;
+ size_t i;
+
+ for (i = 0; i < bytes / 4; i++) {
+ val[i] = k3rtc_readl(priv,
+ REG_K3RTC_SCRATCH0 + offset + (i * 4));
+ }
+
+ return 0;
+}
+
+static int ti_k3_rtc_scratch_write(void *priv_data, unsigned int offset,
+ void *_val, size_t bytes)
+{
+ struct ti_k3_rtc *priv = (struct ti_k3_rtc *)priv_data;
+ u32 *val = _val;
+ size_t i;
+
+ for (i = 0; i < bytes / 4; i++) {
+ k3rtc_writel(priv, REG_K3RTC_SCRATCH0 + offset + (i * 4),
+ val[i]);
+ }
+ return k3rtc_fence(priv);
+}
+
+static struct nvmem_config ti_k3_rtc_nvmem_config = {
+ .name = "ti_k3_rtc_scratch",
+ .word_size = 4,
+ .stride = 4,
+ .size = REG_K3RTC_SCRATCH7 - REG_K3RTC_SCRATCH0 + 4,
+ .reg_read = ti_k3_rtc_scratch_read,
+ .reg_write = ti_k3_rtc_scratch_write,
+};
+
+static int k3rtc_get_32kclk(struct device *dev, struct ti_k3_rtc *priv)
+{
+ int ret;
+ struct clk *clk;
+
+ clk = devm_clk_get(dev, "osc32k");
+ if (IS_ERR(clk)) {
+ dev_err(dev, "No input reference 32k clock\n");
+ return PTR_ERR(clk);
+ }
+
+ ret = clk_prepare_enable(clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable the reference 32k clock(%d)\n", ret);
+ return ret;
+ }
+
+ ret = devm_add_action_or_reset(dev, (void (*)(void *))clk_disable_unprepare, clk);
+ if (ret)
+ return ret;
+
+ priv->rate_32k = clk_get_rate(clk);
+
+ /* Make sure we are exact 32k clock. Else, try to compensate delay */
+ if (priv->rate_32k != 32768)
+ dev_warn(dev, "Clock rate %ld is not 32768! Could misbehave!\n",
+ priv->rate_32k);
+
+ /* Max sync timeout will be two 32k clk sync cycles = ~61uS */
+ priv->sync_timeout_us = (u32)(DIV_ROUND_UP_ULL(1000000, priv->rate_32k) * 2);
+
+ return ret;
+}
+
+static int k3rtc_get_vbusclk(struct device *dev, struct ti_k3_rtc *priv)
+{
+ int ret;
+ struct clk *clk;
+
+ clk = devm_clk_get(dev, "vbus");
+ if (IS_ERR(clk)) {
+ dev_err(dev, "No input vbus clock\n");
+ return PTR_ERR(clk);
+ }
+
+ ret = clk_prepare_enable(clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable the vbus clock(%d)\n", ret);
+ return ret;
+ }
+
+ ret = devm_add_action_or_reset(dev, (void (*)(void *))clk_disable_unprepare, clk);
+ return ret;
+}
+
+static int ti_k3_rtc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ti_k3_rtc *priv;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(struct ti_k3_rtc), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->rtc_base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(priv->rtc_base))
+ return PTR_ERR(priv->rtc_base);
+
+ ret = platform_get_irq(pdev, 0);
+ if (ret < 0)
+ return ret;
+ priv->irq = (unsigned int)ret;
+
+ priv->rtc_dev = devm_rtc_allocate_device(dev);
+ if (IS_ERR(priv->rtc_dev))
+ return PTR_ERR(priv->rtc_dev);
+
+ priv->soc = of_device_get_match_data(dev);
+
+ priv->rtc_dev->ops = &ti_k3_rtc_ops;
+ priv->rtc_dev->range_max = (1ULL << 48) - 1; /* 48Bit seconds */
+ ti_k3_rtc_nvmem_config.priv = priv;
+
+ ret = devm_request_threaded_irq(dev, priv->irq, NULL,
+ ti_k3_rtc_interrupt,
+ IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+ dev_name(dev), dev);
+ if (ret) {
+ dev_err(dev, "Could not request IRQ: %d\n", ret);
+ return ret;
+ }
+
+ ret = k3rtc_get_32kclk(dev, priv);
+ if (ret)
+ return ret;
+ ret = k3rtc_get_vbusclk(dev, priv);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, priv);
+
+ ret = k3rtc_configure(dev);
+ if (ret)
+ return ret;
+
+ if (device_property_present(dev, "wakeup-source"))
+ device_init_wakeup(dev, true);
+ else
+ device_set_wakeup_capable(dev, true);
+
+ ret = devm_rtc_register_device(priv->rtc_dev);
+ if (ret)
+ return ret;
+
+ ret = devm_rtc_nvmem_register(priv->rtc_dev, &ti_k3_rtc_nvmem_config);
+ return ret;
+}
+
+static const struct ti_k3_rtc_soc_data ti_k3_am62_data = {
+ .unlock_irq_erratum = true,
+};
+
+static const struct of_device_id ti_k3_rtc_of_match_table[] = {
+ {.compatible = "ti,am62-rtc", .data = &ti_k3_am62_data},
+ {}
+};
+MODULE_DEVICE_TABLE(of, ti_k3_rtc_of_match_table);
+
+#ifdef CONFIG_PM_SLEEP
+static int ti_k3_rtc_suspend(struct device *dev)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+
+ if (device_may_wakeup(dev))
+ enable_irq_wake(priv->irq);
+ return 0;
+}
+
+static int ti_k3_rtc_resume(struct device *dev)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+
+ if (device_may_wakeup(dev))
+ disable_irq_wake(priv->irq);
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(ti_k3_rtc_pm_ops, ti_k3_rtc_suspend, ti_k3_rtc_resume);
+
+static struct platform_driver ti_k3_rtc_driver = {
+ .probe = ti_k3_rtc_probe,
+ .driver = {
+ .name = "rtc-ti-k3",
+ .of_match_table = ti_k3_rtc_of_match_table,
+ .pm = &ti_k3_rtc_pm_ops,
+ },
+};
+module_platform_driver(ti_k3_rtc_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("TI K3 RTC driver");
+MODULE_AUTHOR("Nishanth Menon");
+MODULE_ALIAS("platform:rtc-ti-k3");
--
2.31.1