[PATCH 2/2] soc: ti: wkup_m3_ipc: Add support for toggling VTT regulator

[Drew Fustini]

From: Dave Gerlach <d-gerlach@xxxxxx>

Some boards (currently AM335x EVM-SK) provides s/w control via
GPIO to toggle VTT regulator to reduce power consumption in low
power state.

The VTT regulator should be disabled after enabling self-refresh on
suspend, and should be enabled before disabling self-refresh on resume.
This is to allow proper self-refresh entry/exit commands to be
transmitted to the memory.

Add support for toggling VTT regulator using DT properties.
Actual toggling happens in CM3 Firmware. The enable option & the GPIO
pin used is collected in A8 Core and then sent to CM3 using IPC
registers.

Note:
Here it is assumed that VTT Toggle will be done using a pin on GPIO-0
Instance. The reason is GPIO-0 is in wakeup domain.

Signed-off-by: Dave Gerlach <d-gerlach@xxxxxx>
Signed-off-by: Keerthy <j-keerthy@xxxxxx>
Signed-off-by: Drew Fustini <dfustini@xxxxxxxxxxxx>
---
 drivers/soc/ti/wkup_m3_ipc.c | 27 +++++++++++++++++++++++++--
 include/linux/wkup_m3_ipc.h  |  1 +
 2 files changed, 26 insertions(+), 2 deletions(-)

diff --git a/drivers/soc/ti/wkup_m3_ipc.c b/drivers/soc/ti/wkup_m3_ipc.c
index 2f03ced0f411..8b92425255a2 100644
--- a/drivers/soc/ti/wkup_m3_ipc.c
+++ b/drivers/soc/ti/wkup_m3_ipc.c
@@ -40,6 +40,13 @@
 #define M3_FW_VERSION_MASK		0xffff
 #define M3_WAKE_SRC_MASK		0xff
 
+#define IPC_MEM_TYPE_SHIFT		(0x0)
+#define IPC_MEM_TYPE_MASK		(0x7 << 0)
+#define IPC_VTT_STAT_SHIFT		(0x3)
+#define IPC_VTT_STAT_MASK		(0x1 << 3)
+#define IPC_VTT_GPIO_PIN_SHIFT		(0x4)
+#define IPC_VTT_GPIO_PIN_MASK		(0x3f << 4)
+
 #define M3_STATE_UNKNOWN		0
 #define M3_STATE_RESET			1
 #define M3_STATE_INITED			2
@@ -215,6 +222,12 @@ static int wkup_m3_is_available(struct wkup_m3_ipc *m3_ipc)
 		(m3_ipc->state != M3_STATE_UNKNOWN));
 }
 
+static void wkup_m3_set_vtt_gpio(struct wkup_m3_ipc *m3_ipc, int gpio)
+{
+	m3_ipc->vtt_conf = (1 << IPC_VTT_STAT_SHIFT) |
+			    (gpio << IPC_VTT_GPIO_PIN_SHIFT);
+}
+
 /* Public functions */
 /**
  * wkup_m3_set_mem_type - Pass wkup_m3 which type of memory is in use
@@ -294,7 +307,8 @@ static int wkup_m3_prepare_low_power(struct wkup_m3_ipc *m3_ipc, int state)
 	/* Program each required IPC register then write defaults to others */
 	wkup_m3_ctrl_ipc_write(m3_ipc, m3_ipc->resume_addr, 0);
 	wkup_m3_ctrl_ipc_write(m3_ipc, m3_power_state, 1);
-	wkup_m3_ctrl_ipc_write(m3_ipc, m3_ipc->mem_type, 4);
+	wkup_m3_ctrl_ipc_write(m3_ipc, m3_ipc->mem_type |
+			       m3_ipc->vtt_conf, 4);
 
 	wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 2);
 	wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 3);
@@ -433,12 +447,13 @@ static int wkup_m3_rproc_boot_thread(void *arg)
 static int wkup_m3_ipc_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
-	int irq, ret;
+	int irq, ret, temp;
 	phandle rproc_phandle;
 	struct rproc *m3_rproc;
 	struct resource *res;
 	struct task_struct *task;
 	struct wkup_m3_ipc *m3_ipc;
+	struct device_node *np = dev->of_node;
 
 	m3_ipc = devm_kzalloc(dev, sizeof(*m3_ipc), GFP_KERNEL);
 	if (!m3_ipc)
@@ -496,6 +511,14 @@ static int wkup_m3_ipc_probe(struct platform_device *pdev)
 
 	m3_ipc->ops = &ipc_ops;
 
+	if (of_find_property(np, "ti,needs-vtt-toggle", NULL) &&
+	    !(of_property_read_u32(np, "ti,vtt-gpio-pin", &temp))) {
+		if (temp >= 0 && temp <= 31)
+			wkup_m3_set_vtt_gpio(m3_ipc, temp);
+		else
+			dev_warn(dev, "Invalid VTT GPIO(%d) pin\n", temp);
+	}
+
 	/*
 	 * Wait for firmware loading completion in a thread so we
 	 * can boot the wkup_m3 as soon as it's ready without holding
diff --git a/include/linux/wkup_m3_ipc.h b/include/linux/wkup_m3_ipc.h
index 3f496967b538..2bc52c6381d5 100644
--- a/include/linux/wkup_m3_ipc.h
+++ b/include/linux/wkup_m3_ipc.h
@@ -33,6 +33,7 @@ struct wkup_m3_ipc {
 
 	int mem_type;
 	unsigned long resume_addr;
+	int vtt_conf;
 	int state;
 
 	struct completion sync_complete;
-- 
2.32.0