Re: [PATCH v2 05/10] spi: aspeed: Add support for direct mapping

[Joel Stanley]

On Wed, 2 Mar 2022 at 17:31, Cédric Le Goater <clg@xxxxxxxx> wrote:
>
> Use direct mapping to read the flash device contents. This operation
> mode is called "Command mode" on Aspeed SoC SMC controllers. It uses a
> Control Register for the settings to apply when a memory operation is
> performed on the flash device mapping window.
>
> If the window is not big enough, fall back to the "User mode" to
> perform the read.
>
> Since direct mapping now handles all reads of the flash device
> contents, also use memcpy_fromio for other address spaces, such as
> SFDP.
>
> Direct mapping for writes will come later when validated.
>
> Signed-off-by: Cédric Le Goater <clg@xxxxxxxx>

Reviewed-by: Joel Stanley <joel@xxxxxxxxx>

> ---
>  drivers/spi/spi-aspeed-smc.c | 67 ++++++++++++++++++++++++++++++++++--
>  1 file changed, 65 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/spi/spi-aspeed-smc.c b/drivers/spi/spi-aspeed-smc.c
> index 688f9472e0d7..b4854b521477 100644
> --- a/drivers/spi/spi-aspeed-smc.c
> +++ b/drivers/spi/spi-aspeed-smc.c
> @@ -324,8 +324,8 @@ static int do_aspeed_spi_exec_op(struct spi_mem *mem, const struct spi_mem_op *o
>                 if (!op->addr.nbytes)
>                         ret = aspeed_spi_read_reg(chip, op);
>                 else
> -                       ret = aspeed_spi_read_user(chip, op, op->addr.val,
> -                                                  op->data.nbytes, op->data.buf.in);
> +                       memcpy_fromio(op->data.buf.in, chip->ahb_base + op->addr.val,
> +                                     op->data.nbytes);
>         } else {
>                 if (!op->addr.nbytes)
>                         ret = aspeed_spi_write_reg(chip, op);
> @@ -405,10 +405,73 @@ static int aspeed_spi_chip_set_default_window(struct aspeed_spi_chip *chip)
>         return chip->ahb_window_size ? 0 : -1;
>  }
>
> +static int aspeed_spi_dirmap_create(struct spi_mem_dirmap_desc *desc)
> +{
> +       struct aspeed_spi *aspi = spi_controller_get_devdata(desc->mem->spi->master);
> +       struct aspeed_spi_chip *chip = &aspi->chips[desc->mem->spi->chip_select];
> +       struct spi_mem_op *op = &desc->info.op_tmpl;
> +       u32 ctl_val;
> +       int ret = 0;
> +
> +       chip->clk_freq = desc->mem->spi->max_speed_hz;
> +
> +       /* Only for reads */
> +       if (op->data.dir != SPI_MEM_DATA_IN)
> +               return -EOPNOTSUPP;
> +
> +       if (desc->info.length > chip->ahb_window_size)
> +               dev_warn(aspi->dev, "CE%d window (%dMB) too small for mapping",
> +                        chip->cs, chip->ahb_window_size >> 20);
> +
> +       /* Define the default IO read settings */
> +       ctl_val = readl(chip->ctl) & ~CTRL_IO_CMD_MASK;
> +       ctl_val |= aspeed_spi_get_io_mode(op) |
> +               op->cmd.opcode << CTRL_COMMAND_SHIFT |
> +               CTRL_IO_DUMMY_SET(op->dummy.nbytes / op->dummy.buswidth) |
> +               CTRL_IO_MODE_READ;
> +
> +       /* Tune 4BYTE address mode */
> +       if (op->addr.nbytes) {
> +               u32 addr_mode = readl(aspi->regs + CE_CTRL_REG);
> +
> +               if (op->addr.nbytes == 4)
> +                       addr_mode |= (0x11 << chip->cs);
> +               else
> +                       addr_mode &= ~(0x11 << chip->cs);
> +               writel(addr_mode, aspi->regs + CE_CTRL_REG);
> +       }
> +
> +       /* READ mode is the controller default setting */
> +       chip->ctl_val[ASPEED_SPI_READ] = ctl_val;
> +       writel(chip->ctl_val[ASPEED_SPI_READ], chip->ctl);
> +
> +       dev_info(aspi->dev, "CE%d read buswidth:%d [0x%08x]\n",
> +                chip->cs, op->data.buswidth, chip->ctl_val[ASPEED_SPI_READ]);
> +
> +       return ret;
> +}
> +
> +static int aspeed_spi_dirmap_read(struct spi_mem_dirmap_desc *desc,
> +                                 u64 offset, size_t len, void *buf)
> +{
> +       struct aspeed_spi *aspi = spi_controller_get_devdata(desc->mem->spi->master);
> +       struct aspeed_spi_chip *chip = &aspi->chips[desc->mem->spi->chip_select];
> +
> +       /* Switch to USER command mode if mapping window is too small */
> +       if (chip->ahb_window_size < offset + len)
> +               aspeed_spi_read_user(chip, &desc->info.op_tmpl, offset, len, buf);
> +       else
> +               memcpy_fromio(buf, chip->ahb_base + offset, len);
> +
> +       return len;
> +}
> +
>  static const struct spi_controller_mem_ops aspeed_spi_mem_ops = {
>         .supports_op = aspeed_spi_supports_op,
>         .exec_op = aspeed_spi_exec_op,
>         .get_name = aspeed_spi_get_name,
> +       .dirmap_create = aspeed_spi_dirmap_create,
> +       .dirmap_read = aspeed_spi_dirmap_read,
>  };
>
>  static void aspeed_spi_chip_set_type(struct aspeed_spi *aspi, unsigned int cs, int type)
> --
> 2.34.1
>