[PATCH net v4] net: phy: marvell: add Marvell specific PHY loopback

From: Mohammad Athari Bin Ismail
Date: Sat Jan 15 2022 - 04:26:14 EST


Existing genphy_loopback() is not applicable for Marvell PHY. Besides
configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control
Register), it is also required to configure same bits in Page 2
Register 21 (MAC Specific Control Register 2) according to speed of
the loopback is operating.

Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).

FIXME: Based on trial and error test, it seem 1G need to have delay between
soft reset and loopback enablement.

Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration")
Cc: <stable@xxxxxxxxxxxxxxx> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@xxxxxxxxx>
---
v4 changelog:
- Rename the function to m88e1510_loopback(). Commented by Heiner Kallweit
<hkallweit1@xxxxxxxxx>.

v3 changelog:
- Use phy_write() to configure speed for BMCR.
- Add error handling.
All commented by Russell King <linux@xxxxxxxxxxxxxxx>

v2 changelog:
- For loopback enabled, add bit-6 and bit-13 configuration in both Page
0 Register 0 and Page 2 Register 21. Commented by Heiner Kallweit
<hkallweit1@xxxxxxxxx>.
- For loopback disabled, follow genphy_loopback() implementation

---
drivers/net/phy/marvell.c | 56 ++++++++++++++++++++++++++++++++++++++-
1 file changed, 55 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 4fcfca4e1702..0ff94400510f 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -189,6 +189,8 @@
#define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII 0x4
#define MII_88E1510_GEN_CTRL_REG_1_RESET 0x8000 /* Soft reset */

+#define MII_88E1510_MSCR_2 0x15
+
#define MII_VCT5_TX_RX_MDI0_COUPLING 0x10
#define MII_VCT5_TX_RX_MDI1_COUPLING 0x11
#define MII_VCT5_TX_RX_MDI2_COUPLING 0x12
@@ -1932,6 +1934,58 @@ static void marvell_get_stats(struct phy_device *phydev,
data[i] = marvell_get_stat(phydev, i);
}

+static int m88e1510_loopback(struct phy_device *phydev, bool enable)
+{
+ int err;
+
+ if (enable) {
+ u16 bmcr_ctl = 0, mscr2_ctl = 0;
+
+ if (phydev->speed == SPEED_1000)
+ bmcr_ctl = BMCR_SPEED1000;
+ else if (phydev->speed == SPEED_100)
+ bmcr_ctl = BMCR_SPEED100;
+
+ if (phydev->duplex == DUPLEX_FULL)
+ bmcr_ctl |= BMCR_FULLDPLX;
+
+ err = phy_write(phydev, MII_BMCR, bmcr_ctl);
+ if (err < 0)
+ return err;
+
+ if (phydev->speed == SPEED_1000)
+ mscr2_ctl = BMCR_SPEED1000;
+ else if (phydev->speed == SPEED_100)
+ mscr2_ctl = BMCR_SPEED100;
+
+ err = phy_modify_paged(phydev, MII_MARVELL_MSCR_PAGE,
+ MII_88E1510_MSCR_2, BMCR_SPEED1000 |
+ BMCR_SPEED100, mscr2_ctl);
+ if (err < 0)
+ return err;
+
+ /* Need soft reset to have speed configuration takes effect */
+ err = genphy_soft_reset(phydev);
+ if (err < 0)
+ return err;
+
+ /* FIXME: Based on trial and error test, it seem 1G need to have
+ * delay between soft reset and loopback enablement.
+ */
+ if (phydev->speed == SPEED_1000)
+ msleep(1000);
+
+ return phy_modify(phydev, MII_BMCR, BMCR_LOOPBACK,
+ BMCR_LOOPBACK);
+ } else {
+ err = phy_modify(phydev, MII_BMCR, BMCR_LOOPBACK, 0);
+ if (err < 0)
+ return err;
+
+ return phy_config_aneg(phydev);
+ }
+}
+
static int marvell_vct5_wait_complete(struct phy_device *phydev)
{
int i;
@@ -3078,7 +3132,7 @@ static struct phy_driver marvell_drivers[] = {
.get_sset_count = marvell_get_sset_count,
.get_strings = marvell_get_strings,
.get_stats = marvell_get_stats,
- .set_loopback = genphy_loopback,
+ .set_loopback = m88e1510_loopback,
.get_tunable = m88e1011_get_tunable,
.set_tunable = m88e1011_set_tunable,
.cable_test_start = marvell_vct7_cable_test_start,
--
2.17.1