[PATCH 5.15 094/128] mmc: meson-mx-sdhc: Set MANUAL_STOP for multi-block SDIO commands

From: Greg Kroah-Hartman
Date: Mon Dec 27 2021 - 10:52:19 EST


From: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>

commit f89b548ca66be7500dcd92ee8e61590f7d08ac91 upstream.

The vendor driver implements special handling for multi-block
SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data
attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC
register for these commands. In all other cases this bit is cleared.
Here we omit SD_IO_RW_DIRECT since that command never has any data
attached to it.

This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_sdiod_ramrw: membytes transfer failed
brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
at 0x00000000
brcmf_sdio_download_firmware: dongle image file download failed

And with this change:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
have limited channels available
brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
version 5.90.195.89.6 FWID 01-b30a427d

Fixes: e4bf1b0970ef96 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
Cc: stable@xxxxxxxxxxxxxxx
Link: https://lore.kernel.org/r/20211219153442.463863-2-martin.blumenstingl@xxxxxxxxxxxxxx
Signed-off-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/mmc/host/meson-mx-sdhc-mmc.c | 16 ++++++++++++++++
1 file changed, 16 insertions(+)

--- a/drivers/mmc/host/meson-mx-sdhc-mmc.c
+++ b/drivers/mmc/host/meson-mx-sdhc-mmc.c
@@ -135,6 +135,7 @@ static void meson_mx_sdhc_start_cmd(stru
struct mmc_command *cmd)
{
struct meson_mx_sdhc_host *host = mmc_priv(mmc);
+ bool manual_stop = false;
u32 ictl, send;
int pack_len;

@@ -172,12 +173,27 @@ static void meson_mx_sdhc_start_cmd(stru
else
/* software flush: */
ictl |= MESON_SDHC_ICTL_DATA_XFER_OK;
+
+ /*
+ * Mimic the logic from the vendor driver where (only)
+ * SD_IO_RW_EXTENDED commands with more than one block set the
+ * MESON_SDHC_MISC_MANUAL_STOP bit. This fixes the firmware
+ * download in the brcmfmac driver for a BCM43362/1 card.
+ * Without this sdio_memcpy_toio() (with a size of 219557
+ * bytes) times out if MESON_SDHC_MISC_MANUAL_STOP is not set.
+ */
+ manual_stop = cmd->data->blocks > 1 &&
+ cmd->opcode == SD_IO_RW_EXTENDED;
} else {
pack_len = 0;

ictl |= MESON_SDHC_ICTL_RESP_OK;
}

+ regmap_update_bits(host->regmap, MESON_SDHC_MISC,
+ MESON_SDHC_MISC_MANUAL_STOP,
+ manual_stop ? MESON_SDHC_MISC_MANUAL_STOP : 0);
+
if (cmd->opcode == MMC_STOP_TRANSMISSION)
send |= MESON_SDHC_SEND_DATA_STOP;