Re: [PATCH] scsi: pm8001: Fix phys_to_virt() usage on dma_addr_t

From: John Garry
Date: Thu Dec 09 2021 - 18:10:12 EST

On 09/12/2021 22:38, Damien Le Moal wrote:
It seems that SSP and STP commands are not completing for some reason,
from the "busy: 222" line.
I have this HBA:

c1:00.0 Serial Attached SCSI controller: ATTO Technology, Inc. ExpressSAS 12Gb/s
SAS/SATA HBA (rev 06)
Subsystem: ATTO Technology, Inc. ExpressSAS H120F

Which uses the pm80xx driver and I do not see such error. E.g.:

[335568.262395] pm80xx 0000:c1:00.0: pm80xx: driver version 0.1.40
[335568.268931] :: pm8001_pci_alloc 529:Setting link rate to default value
[335569.489392] scsi host18: pm80xx
[335570.801031] sas: phy-18:4 added to port-18:0, phy_mask:0x10 (50010860002f5644)
[335570.801225] sas: DOING DISCOVERY on port 0, pid:58830
[335570.801310] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[335570.807638] sas: ata22: end_device-18:0: dev error handler
[335570.964864] ata22.00: ATA-11: WDC WUH721818ALN604, PCGNW232, max UDMA/133
[335579.062526] ata22.00: 4394582016 sectors, multi 0: LBA48 NCQ (depth 32)
[335579.070487] ata22.00: Features: NCQ-sndrcv NCQ-prio
[335579.307260] ata22.00: configured for UDMA/133
[335579.313018] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[335579.323512] scsi 18:0:0:0: Direct-Access ATA WDC WUH721818AL W232
PQ: 0 ANSI: 5
[335579.333243] sas: DONE DISCOVERY on port 0, pid:58830, result:0
[335579.333338] sas: phy-18:5 added to port-18:1, phy_mask:0x20 (50010860002f5645)
[335579.333453] sas: DOING DISCOVERY on port 1, pid:58830
[335579.333596] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[335579.341596] sas: ata23: end_device-18:1: dev error handler
[335579.341640] sas: ata22: end_device-18:0: dev error handler
[335579.500374] ata23.00: ATA-11: WDC WUH721818ALN604, PCGNWTW2, max UDMA/133
[335588.427115] ata23.00: 4394582016 sectors, multi 0: LBA48 NCQ (depth 32)
[335588.435158] ata23.00: Features: NCQ-sndrcv NCQ-prio
[335588.513212] ata23.00: configured for UDMA/133
[335588.519027] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[335588.537683] scsi 18:0:1:0: Direct-Access ATA WDC WUH721818AL WTW2
PQ: 0 ANSI: 5
[335588.565288] sas: DONE DISCOVERY on port 1, pid:58830, result:0
[335588.565543] sas: phy-18:7 added to port-18:2, phy_mask:0x80 (50010860002f5647)
[335588.566917] sas: DOING DISCOVERY on port 2, pid:58830
[335588.567515] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[335588.574948] sas: ata22: end_device-18:0: dev error handler
[335588.574971] sas: ata23: end_device-18:1: dev error handler
[335588.574979] sas: ata24: end_device-18:2: dev error handler
[335588.732190] ata24.00: ATA-11: WDC WSH722020ALN604, PCGMW803, max UDMA/133
[335597.778187] ata24.00: 4882956288 sectors, multi 0: LBA48 NCQ (depth 32)
[335597.788081] ata24.00: Features: NCQ-sndrcv NCQ-prio
[335597.850404] ata24.00: configured for UDMA/133
[335597.856225] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[335597.866680] scsi 18:0:2:0: Direct-Access-ZBC ATA WDC WSH722020AL W803
PQ: 0 ANSI: 7
[335597.876485] sas: DONE DISCOVERY on port 2, pid:58830, result:0
[335597.879720] sd 18:0:0:0: [sdd] 4394582016 4096-byte logical blocks: (18.0
TB/16.4 TiB)
[335597.881483] sd 18:0:0:0: Attached scsi generic sg3 type 0
[335597.888827] sd 18:0:0:0: [sdd] Write Protect is off
[335597.888830] sd 18:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[335597.888839] sd 18:0:0:0: [sdd] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[335597.968683] sd 18:0:1:0: [sde] 4394582016 4096-byte logical blocks: (18.0
TB/16.4 TiB)
[335597.969489] sd 18:0:1:0: Attached scsi generic sg4 type 0
[335597.978210] sd 18:0:1:0: [sde] Write Protect is off
[335597.978214] sd 18:0:1:0: [sde] Mode Sense: 00 3a 00 00
[335597.978228] sd 18:0:1:0: [sde] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[335598.053869] sd 18:0:2:0: [sdf] Host-managed zoned block device
[335598.054476] sd 18:0:2:0: Attached scsi generic sg5 type 20
[335598.066428] sd 18:0:2:0: [sdf] 4882956288 4096-byte logical blocks: (20.0
TB/18.2 TiB)
[335598.093762] sd 18:0:2:0: [sdf] Write Protect is off
[335598.100101] sd 18:0:2:0: [sdf] Mode Sense: 00 3a 00 00
[335598.100119] sd 18:0:2:0: [sdf] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[335598.158832] sd 18:0:1:0: [sde] Attached SCSI disk
[335598.158870] sd 18:0:0:0: [sdd] Attached SCSI disk
[335600.015402] sd 18:0:2:0: [sdf] 74508 zones of 65536 logical blocks
[335600.099235] sd 18:0:2:0: [sdf] Attached SCSI disk

The driver is uselessly verbose (for some reasons, the dbg messages show up),
but no errors.


Here's my log on my arm64 machine:

root@(none)$ echo 0000:04:00.0 > bind
[83.872341] pm80xx 0000:04:00.0: pm80xx: driver version 0.1.40
[83.878359] :: pm8001_pci_alloc 530:Setting link rate to default value
[84.932057] scsi host0: pm80xx
[87.288239] sas: target proto 0x0 at 500e004aaaaaaa1f:0x10 not handled
[87.294793] sas: ex 500e004aaaaaaa1f phy16 failed to discover
[87.360228] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[89.734180] ata4.00: ATA-8: SAMSUNG HM320JI, 2SS00_01, max UDMA7
[89.740185] ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 32)
[93.237158] ata4.00: configured for UDMA/133
[93.241435] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[93.262941] scsi 0:0:0:0: Direct-Access SEAGATE ST2000NM0045 N004 PQ: 0 ANSI: 6
[93.275710] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[93.284159] sd 0:0:0:0: [sda] Write Protect is off
[93.284423] scsi 0:0:1:0: Direct-Access SEAGATE ST2000NM0045 N004 PQ: 0 ANSI: 6
[93.298317] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[93.300128] scsi 0:0:2:0: Direct-Access ATASAMSUNG HM320JI 0_01 PQ: 0 ANSI: 5
[93.301689] sd 0:0:1:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[93.302366] sd 0:0:1:0: [sdb] Write Protect is off
[93.303636] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
[93.311335] sdb: sdb1
[93.315129] sd 0:0:2:0: [sdc] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[93.315678] sda: sda1
[93.315898] scsi 0:0:3:0: Direct-Access SEAGATE ST1000NM0023 0006 PQ: 0 ANSI: 6
[93.321138] sd 0:0:0:0: [sda] Attached SCSI disk
[93.328114] sd 0:0:1:0: [sdb] Attached SCSI disk
[93.335947] sd 0:0:2:0: [sdc] Write Protect is off
[93.344840] scsi 0:0:4:0: EnclosureHUAWEIExpander 12Gx16 128 PQ: 0 ANSI: 6
[93.345274] sd 0:0:3:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[93.345634] sd 0:0:3:0: [sdd] Write Protect is off
[93.346268] sd 0:0:3:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
[93.351997] sdd: sdd1 sdd2
[93.355067] sd 0:0:3:0: [sdd] Attached SCSI disk
[93.356196] sd 0:0:2:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[93.401162] sdc: sdc1 sdc2 sdc3
[93.406853] sd 0:0:2:0: [sdc] Attached SCSI disk
[93.425508] sas: ex 500e004aaaaaaa1f phy08 change count has changed
[93.435927] sas: target proto 0x0 at 500e004aaaaaaa1f:0x11 not handled
[93.442480] sas: ex 500e004aaaaaaa1f phy17 failed to discover
[93.448737] sas: target proto 0x0 at 500e004aaaaaaa1f:0x12 not handled
[93.455288] sas: ex 500e004aaaaaaa1f phy18 failed to discover
[93.461527] sas: target proto 0x0 at 500e004aaaaaaa1f:0x13 not handled
[93.468081] sas: ex 500e004aaaaaaa1f phy19 failed to discover
[93.479734] sas: ex 500e004aaaaaaa1f phys DID NOT change
[93.500240] sas: ex 500e004aaaaaaa1f phys DID NOT change
[93.510489] sas: ex 500e004aaaaaaa1f phys DID NOT change
[93.520714] sas: ex 500e004aaaaaaa1f phys DID NOT change
[93.531000] sas: ex 500e004aaaaaaa1f phys DID NOT change
[93.541351] sas: ex 500e004aaaaaaa1f phys DID NOT change
[93.551721] sas: ex 500e004aaaaaaa1f phys DID NOT change
[93.562066] sas: ex 500e004aaaaaaa1f phys DID NOT change
root@(none)$
root@(none)$
root@(none)$

And then it's the mounting a partition or examining it which hangs quite reliably:

root@(none)$ mount /dev/sda1 mnt
[ 104.232655] EXT4-fs (sda1): recovery complete
[ 104.237021] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
root@(none)$ ls mnt
[ 136.842085] sas: Enter sas_scsi_recover_host busy: 203 failed: 203
[ 136.848286] sas: sas_scsi_find_task: aborting task 0x(____ptrval____)
[ 157.280267] pm80xx1:: pm8001_exec_internal_tmf_task 756:TMF task[1]timeout.
[ 171.283579] pm80xx1:: mpi_ssp_completion 1935:sas IO status 0x1
[ 171.283584] pm80xx1:: pm8001_abort_task 1327:rc= -5
[ 171.289579] pm80xx1:: mpi_ssp_completion 1946:SAS Address of IO Failure Drive:5000c500a7b95a49
[ 171.289583] pm80xx1:: mpi_ssp_completion 2184:task 0x(____ptrval____) done with io_status 0x1 resp 0x0 stat 0x8d but aborted by upper layer!
[ 171.315904] sas: sas_eh_handle_sas_errors: task 0x(____ptrval____) is done
[ 171.322769] sas: sas_scsi_find_task: aborting task 0x(____ptrval____)

Earlier today it was the mount command which was hanging. From debugging that, I found that the very first SSP command when mounting is sent the HW successfully but no completion interrupt ever occurs there - I really don't know why. Other SSP commands complete successfully before this and after (TMFs in the error handling), including ones which have sgls.

sda is a SAS drive, but I think SATA has the same issue - I was just looking at sda.

One thing I noticed in the driver is that it uses mb() in between writing to the DMA memory and initiating the HW - I don't think mb is strong enough. However I don't think that is my issue - it wouldn't fail reliably if it was.

Thanks,
John