Re: [PATCH] scsi: pm8001: Fix phys_to_virt() usage on dma_addr_t

[John Garry]

On 26/11/2021 15:35, John Garry wrote:
>   	/*
> @@ -4280,8 +4283,9 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha,
>   		pm8001_ha->smp_exp_mode = SMP_INDIRECT;
>   
>   
> -	tmp_addr = cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_req));
> -	preq_dma_addr = (char *)phys_to_virt(tmp_addr);
> +	smp_req = &task->smp_task.smp_req;
> +	to = kmap(sg_page(smp_req));

This should be a kmap_atomic() as well, as I see the following for when 
CONFIG_DEBUG_ATOMIC_SLEEP is enabled:

[   27.222116]  dump_backtrace+0x0/0x2b4
[   27.225774]  show_stack+0x1c/0x30
[   27.229084]  dump_stack_lvl+0x68/0x84
[   27.232741]  dump_stack+0x20/0x3c
[   27.236049]  __might_resched+0x1d4/0x240
[   27.239967]  __might_sleep+0x70/0xd0
[   27.243536]  pm80xx_chip_smp_req+0x2c4/0x56c
[   27.247802]  pm8001_task_exec.constprop.0+0x718/0x770
[   27.252848]  pm8001_queue_command+0x1c/0x2c
[   27.257026]  smp_execute_task_sg+0x1e8/0x370
[   27.261289]  sas_ex_phy_discover+0x29c/0x31c
[   27.265553]  smp_ata_check_ready+0x74/0x190
[   27.269729]  ata_wait_ready+0xd0/0x224
[   27.273474]  ata_wait_after_reset+0x78/0xac
[   27.277652]  sas_ata_hard_reset+0xf0/0x18c
[   27.281742]  ata_do_reset.constprop.0+0x80/0x9c
[   27.286266]  ata_eh_reset+0xba4/0x1170
[   27.290008]  ata_eh_recover+0x4b0/0x1b40
[   27.293924]  ata_do_eh+0x8c/0x110
[   27.297232]  ata_std_error_handler+0x80/0xb0
[   27.301495]  ata_scsi_port_error_handler+0x3d4/0x9d0
[   27.306454]  async_sas_ata_eh+0x70/0xf8
[   27.310285]  async_run_entry_fn+0x5c/0x1e0
[   27.314375]  process_one_work+0x378/0x630
[   27.318379]  worker_thread+0xa8/0x6bc
[   27.322033]  kthread+0x214/0x230
[   27.325256]  ret_from_fork+0x10/0x20
[   27.328825] pm80xx0:: pm80xx_chip_smp_req  4292:SMP REQUEST INDIRECT MODE

But I don't think that this is the problem which causes error handling 
to kick in later, as discussed in this thread.

> +	payload = to + smp_req->offset;
>   
>   	/* INDIRECT MODE command settings. Use DMA */
>   	if (pm8001_ha->smp_exp_mode == SMP_INDIRECT) {
> @@ -4289,7 +4293,7 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha,
>   		/* for SPCv indirect mode. Place the top 4 bytes of
>   		 * SMP Request header here. */
>   		for (i = 0; i < 4; i++)
> -			smp_cmd.smp_req16[i] = *(preq_dma_addr + i);
> +			smp_cmd.smp_req16[i] = *(payload + i);