Re: [PATCH 2/3] arm64: dts: rockchip: Add spi nodes on rk356x

From: Heiko Stübner
Date: Fri Nov 26 2021 - 14:01:23 EST


Am Freitag, 26. November 2021, 18:51:29 CET schrieb Johan Jonker:
> Hi Nicolas,
>
> Could you test with:
> ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- make dtbs_check
> DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-rockchip.yaml
>
> On 11/26/21 4:43 PM, Nicolas Frattaroli wrote:
> > This adds the four spi nodes (spi0, spi1, spi2, spi3) to the
> > rk356x dtsi. These are from the downstream device tree, though
> > I have double-checked that their interrupts and DMA numbers are
> > correct. I have also tested spi1 with an SPI device.
> >
> > Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@xxxxxxxxx>
> > ---
> > arch/arm64/boot/dts/rockchip/rk356x.dtsi | 68 ++++++++++++++++++++++++
> > 1 file changed, 68 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > index 46d9552f6028..57c0197cc65a 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > +++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > @@ -39,6 +39,10 @@ aliases {
> > serial7 = &uart7;
> > serial8 = &uart8;
> > serial9 = &uart9;
> > + spi0 = &spi0;
> > + spi1 = &spi1;
> > + spi2 = &spi2;
> > + spi3 = &spi3;
> > };
> >
> > cpus {
> > @@ -742,6 +746,70 @@ wdt: watchdog@fe600000 {
> > clock-names = "tclk", "pclk";
> > };
> >
> > + spi0: spi@fe610000 {
> > + compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
> > + reg = <0x0 0xfe610000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
>
> > + #address-cells = <1>;
> > + #size-cells = <0>;
>
> Move above status.
>
> > + clocks = <&cru CLK_SPI0>, <&cru PCLK_SPI0>;
> > + clock-names = "spiclk", "apb_pclk";
> > + dmas = <&dmac0 20>, <&dmac0 21>;
> > + dma-names = "tx", "rx";
>
> > + pinctrl-names = "default", "high_speed";
>
> Keep position of pinctrl-names in line with other nodes in this file
> below pinctrl-0.

I do believe we always have pinctrl-names on top in most dts files, as it
describes what the -0, -1 etc are, i.e.
pinctrl-names = "statename-for-0", "statename-for-1", "statename-for-2"...
pinctrl-0 =
pinctrl-1 =


Heiko

> arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dt.yaml: spi@fe610000:
> pinctrl-names:1: 'sleep' was expected
> From schema: /Documentation/devicetree/bindings/spi/spi-rockchip.yaml
>
> Missing "high_speed" support?
>
> spi: rockchip: set higher io driver when sclk higher than 24MHz
> https://github.com/rockchip-linux/kernel/commit/7e4349ec9d70dbcfe7f78125700d2685539ea1bd
>
> > + pinctrl-0 = <&spi0m0_cs0 &spi0m0_cs1 &spi0m0_pins>;
>
> > + pinctrl-1 = <&spi0m0_cs0 &spi0m0_cs1 &spi0m0_pins_hs>;
>
> Missing Linux mainline driver and document support? Maybe skip for now?
>
> spi0m0_cs0_hs spi0m0_cs1_hs ???
>
> > + status = "disabled";
> > + };
> > +
>
>
>
> spi0 {
> /omit-if-no-ref/
> spi0m0_pins: spi0m0-pins {
> rockchip,pins =
> /* spi0_clkm0 */
> <0 RK_PB5 2 &pcfg_pull_none>,
> /* spi0_misom0 */
> <0 RK_PC5 2 &pcfg_pull_none>,
> /* spi0_mosim0 */
> <0 RK_PB6 2 &pcfg_pull_none>;
> };
>
> /omit-if-no-ref/
> spi0m0_cs0: spi0m0-cs0 {
> rockchip,pins =
> /* spi0_cs0m0 */
> <0 RK_PC6 2 &pcfg_pull_none>;
> };
>
> /omit-if-no-ref/
> spi0m0_cs1: spi0m0-cs1 {
> rockchip,pins =
> /* spi0_cs1m0 */
> <0 RK_PC4 2 &pcfg_pull_none>;
> };
>
> /omit-if-no-ref/
> spi0m1_pins: spi0m1-pins {
> rockchip,pins =
> /* spi0_clkm1 */
> <2 RK_PD3 3 &pcfg_pull_none>,
> /* spi0_misom1 */
> <2 RK_PD0 3 &pcfg_pull_none>,
> /* spi0_mosim1 */
> <2 RK_PD1 3 &pcfg_pull_none>;
> };
>
> /omit-if-no-ref/
> spi0m1_cs0: spi0m1-cs0 {
> rockchip,pins =
> /* spi0_cs0m1 */
> <2 RK_PD2 3 &pcfg_pull_none>;
> };
> };
>
> spi0-hs {
> /omit-if-no-ref/
> spi0m0_pins_hs: spi0m0-pins {
> rockchip,pins =
> /* spi0_clkm0 */
> <0 RK_PB5 2 &pcfg_pull_up_drv_level_1>,
> /* spi0_misom0 */
> <0 RK_PC5 2 &pcfg_pull_up_drv_level_1>,
> /* spi0_mosim0 */
> <0 RK_PB6 2 &pcfg_pull_up_drv_level_1>;
> };
>
> /omit-if-no-ref/
> spi0m0_cs0_hs: spi0m0-cs0 {
> rockchip,pins =
> /* spi0_cs0m0 */
> <0 RK_PC6 2 &pcfg_pull_up_drv_level_1>;
> };
>
> /omit-if-no-ref/
> spi0m0_cs1_hs: spi0m0-cs1 {
> rockchip,pins =
> /* spi0_cs1m0 */
> <0 RK_PC4 2 &pcfg_pull_up_drv_level_1>;
> };
>
> /omit-if-no-ref/
> spi0m1_pins_hs: spi0m1-pins {
> rockchip,pins =
> /* spi0_clkm1 */
> <2 RK_PD3 3 &pcfg_pull_up_drv_level_1>,
> /* spi0_misom1 */
> <2 RK_PD0 3 &pcfg_pull_up_drv_level_1>,
> /* spi0_mosim1 */
> <2 RK_PD1 3 &pcfg_pull_up_drv_level_1>;
> };
>
> /omit-if-no-ref/
> spi0m1_cs0_hs: spi0m1-cs0 {
> rockchip,pins =
> /* spi0_cs0m1 */
> <2 RK_PD2 3 &pcfg_pull_up_drv_level_1>;
> };
> };
>
>
>
> > + spi1: spi@fe620000 {
> > + compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
> > + reg = <0x0 0xfe620000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + clocks = <&cru CLK_SPI1>, <&cru PCLK_SPI1>;
> > + clock-names = "spiclk", "apb_pclk";
> > + dmas = <&dmac0 22>, <&dmac0 23>;
> > + dma-names = "tx", "rx";
> > + pinctrl-names = "default", "high_speed";
> > + pinctrl-0 = <&spi1m0_cs0 &spi1m0_cs1 &spi1m0_pins>;
> > + pinctrl-1 = <&spi1m0_cs0 &spi1m0_cs1 &spi1m0_pins_hs>;
> > + status = "disabled";
> > + };
> > +
> > + spi2: spi@fe630000 {
> > + compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
> > + reg = <0x0 0xfe630000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + clocks = <&cru CLK_SPI2>, <&cru PCLK_SPI2>;
> > + clock-names = "spiclk", "apb_pclk";
> > + dmas = <&dmac0 24>, <&dmac0 25>;
> > + dma-names = "tx", "rx";
> > + pinctrl-names = "default", "high_speed";
> > + pinctrl-0 = <&spi2m0_cs0 &spi2m0_cs1 &spi2m0_pins>;
> > + pinctrl-1 = <&spi2m0_cs0 &spi2m0_cs1 &spi2m0_pins_hs>;
> > + status = "disabled";
> > + };
> > +
> > + spi3: spi@fe640000 {
> > + compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
> > + reg = <0x0 0xfe640000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + clocks = <&cru CLK_SPI3>, <&cru PCLK_SPI3>;
> > + clock-names = "spiclk", "apb_pclk";
> > + dmas = <&dmac0 26>, <&dmac0 27>;
> > + dma-names = "tx", "rx";
> > + pinctrl-names = "default", "high_speed";
> > + pinctrl-0 = <&spi3m0_cs0 &spi3m0_cs1 &spi3m0_pins>;
> > + pinctrl-1 = <&spi3m0_cs0 &spi3m0_cs1 &spi3m0_pins_hs>;
> > + status = "disabled";
> > + };
> > +
> > uart1: serial@fe650000 {
> > compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> > reg = <0x0 0xfe650000 0x0 0x100>;
> >
>