[PATCH v2 09/14] mtd: spinand: winbond: Add octal_dtr_enable() for manufacturer_ops

From: Apurva Nandan
Date: Mon Oct 11 2021 - 16:49:17 EST


Add implementation of octal_dtr_enable() manufacturer_ops for Winbond.
To switch to Ocatl DTR mode, setting programmable dummy cycles and
SPI IO mode using the volatile configuration register is required. To
function at max 120MHz SPI clock in Octal DTR mode, 12 programmable
dummy clock cycle setting is required. (Default number of dummy cycle
are 8 clocks)

Set the programmable dummy cycle to 12 clocks, and SPI IO mode to
Octal DTR with Data Strobe in the VCR. Also, perform a READ ID
operation in Octal DTR SPI mode to ensure the switch was successful.

Datasheet: https://www.winbond.com/export/sites/winbond/datasheet/W35N01JW_Datasheet_Brief.pdf

Signed-off-by: Apurva Nandan <a-nandan@xxxxxx>
---
drivers/mtd/nand/spi/winbond.c | 42 ++++++++++++++++++++++++++++++++++
1 file changed, 42 insertions(+)

diff --git a/drivers/mtd/nand/spi/winbond.c b/drivers/mtd/nand/spi/winbond.c
index 89d8ee801f56..e2cb82d68f96 100644
--- a/drivers/mtd/nand/spi/winbond.c
+++ b/drivers/mtd/nand/spi/winbond.c
@@ -16,6 +16,14 @@

#define WINBOND_CFG_BUF_READ BIT(3)

+/* Octal DTR SPI mode (8D-8D-8D) with Data Strobe output*/
+#define WINBOND_IO_MODE_VCR_OCTAL_DTR 0xE7
+#define WINBOND_IO_MODE_VCR_ADDR 0x00
+
+/* Use 12 dummy clk cycles for using Octal DTR SPI at max 120MHZ */
+#define WINBOND_DUMMY_CLK_COUNT 12
+#define WINBOND_DUMMY_CLK_VCR_ADDR 0x01
+
static SPINAND_OP_VARIANTS(read_cache_variants,
SPINAND_PAGE_READ_FROM_CACHE_QUADIO_OP(0, 2, NULL, 0),
SPINAND_PAGE_READ_FROM_CACHE_X4_OP(0, 1, NULL, 0),
@@ -156,8 +164,42 @@ static int winbond_write_vcr_op(struct spinand_device *spinand, u8 reg, u8 val)
return 0;
}

+static int winbond_spinand_octal_dtr_enable(struct spinand_device *spinand)
+{
+ int ret;
+ struct spi_mem_op op;
+
+ ret = winbond_write_vcr_op(spinand, WINBOND_DUMMY_CLK_VCR_ADDR,
+ WINBOND_DUMMY_CLK_COUNT);
+ if (ret)
+ return ret;
+
+ ret = winbond_write_vcr_op(spinand, WINBOND_IO_MODE_VCR_ADDR,
+ WINBOND_IO_MODE_VCR_OCTAL_DTR);
+ if (ret)
+ return ret;
+
+ /* Read flash ID to make sure the switch was successful. */
+ op = (struct spi_mem_op)
+ SPI_MEM_OP(SPI_MEM_OP_CMD_DTR(2, 0x9f9f, 8),
+ SPI_MEM_OP_NO_ADDR,
+ SPI_MEM_OP_DUMMY_DTR(16, 8),
+ SPI_MEM_OP_DATA_IN_DTR(SPINAND_MAX_ID_LEN,
+ spinand->scratchbuf, 8));
+
+ ret = spi_mem_exec_op(spinand->spimem, &op);
+ if (ret)
+ return ret;
+
+ if (memcmp(spinand->scratchbuf, spinand->id.data, SPINAND_MAX_ID_LEN))
+ return -EINVAL;
+
+ return 0;
+}
+
static const struct spinand_manufacturer_ops winbond_spinand_manuf_ops = {
.init = winbond_spinand_init,
+ .octal_dtr_enable = winbond_spinand_octal_dtr_enable,
};

const struct spinand_manufacturer winbond_spinand_manufacturer = {
--
2.25.1