[PATCH v2 08/14] mtd: spinand: winbond: Add support for write volatile configuration register op

From: Apurva Nandan
Date: Mon Oct 11 2021 - 16:47:32 EST


Volatile configuration register are a different set of configuration
registers, i.e. they differ from the status registers. A different
SPI instruction is required to write to these registers. Any changes
to the Volatile Configuration Register get transferred directly to
the Internal Configuration Register and instantly reflect on the
device operation.

In Winbond W35N01JW, these volatile configuration register must be
configured in order to switch to Octal DTR SPI mode.

Add support for writing to volatile configuration registers using a
new WRITE_VCR_OP template.

Datasheet: https://www.winbond.com/export/sites/winbond/datasheet/W35N01JW_Datasheet_Brief.pdf

Signed-off-by: Apurva Nandan <a-nandan@xxxxxx>
---
drivers/mtd/nand/spi/core.c | 2 +-
drivers/mtd/nand/spi/winbond.c | 42 ++++++++++++++++++++++++++++++++++
include/linux/mtd/spinand.h | 1 +
3 files changed, 44 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/nand/spi/core.c b/drivers/mtd/nand/spi/core.c
index 1210946f8447..2bea21bd9747 100644
--- a/drivers/mtd/nand/spi/core.c
+++ b/drivers/mtd/nand/spi/core.c
@@ -445,7 +445,7 @@ static void spinand_ondie_ecc_save_status(struct nand_device *nand, u8 status)
engine_conf->status = status;
}

-static int spinand_write_enable_op(struct spinand_device *spinand)
+int spinand_write_enable_op(struct spinand_device *spinand)
{
struct spi_mem_op op = SPINAND_WR_EN_DIS_OP(true);

diff --git a/drivers/mtd/nand/spi/winbond.c b/drivers/mtd/nand/spi/winbond.c
index 76684428354e..89d8ee801f56 100644
--- a/drivers/mtd/nand/spi/winbond.c
+++ b/drivers/mtd/nand/spi/winbond.c
@@ -7,6 +7,7 @@
* Boris Brezillon <boris.brezillon@xxxxxxxxxxx>
*/

+#include <linux/delay.h>
#include <linux/device.h>
#include <linux/kernel.h>
#include <linux/mtd/spinand.h>
@@ -114,6 +115,47 @@ static int winbond_spinand_init(struct spinand_device *spinand)
return 0;
}

+/**
+ * winbond_write_vcr_op() - write values onto the volatile configuration
+ * registers (VCR)
+ * @spinand: the spinand device
+ * @reg: the address of the particular reg in the VCR to be written on
+ * @val: the value to be written on the reg in the VCR
+ *
+ * Volatile configuration registers are a separate set of configuration
+ * registers, i.e. they differ from the status registers SR-1/2/3. A different
+ * SPI instruction is required to write to these registers. Any changes
+ * to the Volatile Configuration Register get transferred directly to
+ * the Internal Configuration Register and instantly reflect on the
+ * device operation.
+ */
+static int winbond_write_vcr_op(struct spinand_device *spinand, u8 reg, u8 val)
+{
+ int ret;
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(0x81, 1),
+ SPI_MEM_OP_ADDR(3, reg, 1),
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(1, spinand->scratchbuf, 1));
+
+ *spinand->scratchbuf = val;
+
+ ret = spinand_write_enable_op(spinand);
+ if (ret)
+ return ret;
+
+ ret = spi_mem_exec_op(spinand->spimem, &op);
+ if (ret)
+ return ret;
+
+ /*
+ * Write VCR operation doesn't set the busy bit in SR, so can't perform
+ * a status poll. Minimum time of 50ns is needed to complete the write.
+ * So, give thrice the minimum required delay.
+ */
+ ndelay(150);
+ return 0;
+}
+
static const struct spinand_manufacturer_ops winbond_spinand_manuf_ops = {
.init = winbond_spinand_init,
};
diff --git a/include/linux/mtd/spinand.h b/include/linux/mtd/spinand.h
index daa2ac5c3110..21a4e5adcd59 100644
--- a/include/linux/mtd/spinand.h
+++ b/include/linux/mtd/spinand.h
@@ -560,5 +560,6 @@ int spinand_match_and_init(struct spinand_device *spinand,

int spinand_upd_cfg(struct spinand_device *spinand, u8 mask, u8 val);
int spinand_select_target(struct spinand_device *spinand, unsigned int target);
+int spinand_write_enable_op(struct spinand_device *spinand);

#endif /* __LINUX_MTD_SPINAND_H */
--
2.25.1