[PATCH] dt-bindings: power: reset: gpio-poweroff: Convert txt bindings to yaml

[David Heidelberg]

Convert power-off action connected to the GPIO documentation to the YAML syntax.

Signed-off-by: David Heidelberg <david@xxxxxxx>
---
 .../bindings/power/reset/gpio-poweroff.txt    | 41 ------------
 .../bindings/power/reset/gpio-poweroff.yaml   | 64 +++++++++++++++++++
 2 files changed, 64 insertions(+), 41 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt
 create mode 100644 Documentation/devicetree/bindings/power/reset/gpio-poweroff.yaml

diff --git a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt
deleted file mode 100644
index 3e56c1b34a4c..000000000000
--- a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt
+++ /dev/null
@@ -1,41 +0,0 @@
-Driver a GPIO line that can be used to turn the power off.
-
-The driver supports both level triggered and edge triggered power off.
-At driver load time, the driver will request the given gpio line and
-install a handler to power off the system. If the optional properties
-'input' is not found, the GPIO line will be driven in the inactive
-state. Otherwise its configured as an input.
-
-When the power-off handler is called, the gpio is configured as an
-output, and drive active, so triggering a level triggered power off
-condition. This will also cause an inactive->active edge condition, so
-triggering positive edge triggered power off. After a delay of 100ms,
-the GPIO is set to inactive, thus causing an active->inactive edge,
-triggering negative edge triggered power off. After another 100ms
-delay the GPIO is driver active again. If the power is still on and
-the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted.
-
-Required properties:
-- compatible : should be "gpio-poweroff".
-- gpios : The GPIO to set high/low, see "gpios property" in
-  Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be
-  low to power down the board set it to "Active Low", otherwise set
-  gpio to "Active High".
-
-Optional properties:
-- input : Initially configure the GPIO line as an input. Only reconfigure
-  it to an output when the power-off handler is called. If this optional
-  property is not specified, the GPIO is initialized as an output in its
-  inactive state.
-- active-delay-ms: Delay (default 100) to wait after driving gpio active
-- inactive-delay-ms: Delay (default 100) to wait after driving gpio inactive
-- timeout-ms: Time to wait before asserting a WARN_ON(1). If nothing is
-              specified, 3000 ms is used.
-
-Examples:
-
-gpio-poweroff {
-	compatible = "gpio-poweroff";
-	gpios = <&gpio 4 0>;
-	timeout-ms = <3000>;
-};
diff --git a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.yaml b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.yaml
new file mode 100644
index 000000000000..50ae0cec6493
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.yaml
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/reset/gpio-poweroff.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Driver a GPIO line that can be used to turn the power off
+
+maintainers:
+  - Sebastian Reichel <sre@xxxxxxxxxx>
+
+description:
+  The driver supports both level triggered and edge triggered power off.
+  At driver load time, the driver will request the given gpio line and
+  install a handler to power off the system. If the optional properties
+  'input' is not found, the GPIO line will be driven in the inactive
+  state. Otherwise its configured as an input.
+
+  When the power-off handler is called, the gpio is configured as an
+  output, and drive active, so triggering a level triggered power off
+  condition. This will also cause an inactive->active edge condition, so
+  triggering positive edge triggered power off. After a delay of 100ms,
+  the GPIO is set to inactive, thus causing an active->inactive edge,
+  triggering negative edge triggered power off. After another 100ms
+  delay the GPIO is driver active again. If the power is still on and
+  the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted.
+
+properties:
+  compatible:
+    const: gpio-poweroff
+
+  gpios: true
+
+  input:
+    description: |
+      Initially configure the GPIO line as an input. Only reconfigure
+      it to an output when the power-off handler is called. If this optional
+      property is not specified, the GPIO is initialized as an output in its inactive state.
+
+  active-delay-ms:
+    default: 100
+    description: Delay to wait after driving gpio active
+
+  inactive-delay-ms:
+    default: 100
+    description: Delay to wait after driving gpio inactive
+
+  timeout-ms:
+    default: 3000
+    description: Time to wait before asserting a WARN_ON(1).
+
+required:
+  - compatible
+  - gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    gpio-poweroff {
+        compatible = "gpio-poweroff";
+        gpios = <&gpio 4 0>;
+        timeout-ms = <3000>;
+    };
-- 
2.33.0