Re: [PATCH v9 3/4] arm64: dts: qcom: sc7280: Add PCIe nodes for IDP board

From: Prasad Malisetty
Date: Wed Sep 29 2021 - 11:54:05 EST


On 2021-09-29 02:22, Stephen Boyd wrote:
Quoting Prasad Malisetty (2021-09-28 06:55:49)
Enable PCIe controller and PHY for sc7280 IDP board.
Add specific NVMe GPIO entries for SKU1 and SKU2 support.

Signed-off-by: Prasad Malisetty <pmaliset@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc7280-idp.dts | 9 ++++++
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 54 ++++++++++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/sc7280-idp2.dts | 9 ++++++
3 files changed, 72 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 64fc22a..1562386 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -61,6 +61,15 @@
modem-init;
};

+&nvme_pwren_pin {
+ pins = "gpio19";
+};

This should move to the bottom in the "pinctrl" section.

+
+&nvme_3v3_regulators {
+ gpio = <&tlmm 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;

The enable-active-high can be in the idp.dtsi file? That doesn't seem to
change.

+};
+
&pmk8350_vadc {
pmr735a_die_temp {
reg = <PMR735A_ADC7_DIE_TEMP>;
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index def22ff..5b5505f 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -31,6 +31,17 @@
linux,can-disable;
};
};
+
+ nvme_3v3_regulators: nvme-3v3-regulators {

Why plural? Isn't it a single regulator?

+ compatible = "regulator-fixed";
+ regulator-name = "VLDO_3V3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&nvme_pwren_pin>;
+ };
};

&apps_rsc {
@@ -220,6 +231,42 @@
modem-init;
};

+&pcie1 {
+ status = "okay";
+ perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
+
+ vddpe-3v3-supply = <&nvme_3v3_regulators>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie1_default_state>;
+};
+
+&pcie1_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l10c_0p8>;
+ vdda-pll-supply = <&vreg_l6b_1p2>;
+};
+
+&pcie1_default_state {

I thought the node would be split into a reset config node and a wake
config node. Is that not being done for some reason? The pinctrl-0 would
look like

pinctrl-0 = <&pcie1_default_state>, <&pcie1_reset_n>, <&pcie1_wake_n>;

+ reset-n {
+ pins = "gpio2";
+ function = "gpio";
+
+ drive-strength = <16>;
+ output-low;
+ bias-disable;
+ };
+
+ wake-n {
+ pins = "gpio3";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+};
+
&pmk8350_vadc {
pmk8350_die_temp {
reg = <PMK8350_ADC7_DIE_TEMP>;
@@ -489,3 +536,10 @@
bias-pull-up;
};
};
+
+&tlmm {
+ nvme_pwren_pin: nvme-pwren-pin {
+ function = "gpio";
+ bias-pull-up;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
index 1fc2add..0548cb6 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
@@ -21,3 +21,12 @@
stdout-path = "serial0:115200n8";
};
};
+
+&nvme_pwren_pin {
+ pins = "gpio51";
+};

The pin config can go to a pinctrl section at the bottom of this file?

Hi Stephen,

Thanks for the review and comments.

Sure, I will address all the comments and incorporate the changes in next version series.

Thanks
-Prasad
+
+&nvme_3v3_regulators {
+ gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+};