Re: [BUG] rockpro64: PCI BAR reassignment broken by commit 9d57e61bf723 ("of/pci: Add IORESOURCE_MEM_64 to resource flags for 64-bit memory addresses")

From: Ard Biesheuvel
Date: Tue May 25 2021 - 13:18:18 EST


On Tue, 25 May 2021 at 19:01, Peter Geis <pgwipeout@xxxxxxxxx> wrote:
>
> On Tue, May 25, 2021 at 12:44 PM Ard Biesheuvel <ardb@xxxxxxxxxx> wrote:
> >
> > On Tue, 25 May 2021 at 18:23, Peter Geis <pgwipeout@xxxxxxxxx> wrote:
> > >
> > > On Tue, May 25, 2021 at 11:55 AM Ard Biesheuvel <ardb@xxxxxxxxxx> wrote:
> > > >
> > > > On Tue, 25 May 2021 at 17:34, Peter Geis <pgwipeout@xxxxxxxxx> wrote:
> > > > >
> > > > > On Tue, May 25, 2021 at 9:57 AM Ard Biesheuvel <ardb@xxxxxxxxxx> wrote:
> > > > > >
> > > > > > On Tue, 25 May 2021 at 15:42, Punit Agrawal <punitagrawal@xxxxxxxxx> wrote:
> > > > > > >
> > > > > > > Hi Ard,
> > > > > > >
> > > > > > > Ard Biesheuvel <ardb@xxxxxxxxxx> writes:
> > > > > > >
> > > > > > > > On Sun, 23 May 2021 at 13:06, Punit Agrawal <punitagrawal@xxxxxxxxx> wrote:
> > > > > > > >>
> > > > > > > >> Robin Murphy <robin.murphy@xxxxxxx> writes:
> > > > > > > >>
> > > > > > > >> > [ +linux-pci for visibility ]
> > > > > > > >> >
> > > > > > > >> > On 2021-05-18 10:09, Alexandru Elisei wrote:
> > > > > > > >> >> After doing a git bisect I was able to trace the following error when booting my
> > > > > > > >> >> rockpro64 v2 (rk3399 SoC) with a PCIE NVME expansion card:
> > > > > > > >> >> [..]
> > > > > > > >> >> [ 0.305183] rockchip-pcie f8000000.pcie: host bridge /pcie@f8000000 ranges:
> > > > > > > >> >> [ 0.305248] rockchip-pcie f8000000.pcie: MEM 0x00fa000000..0x00fbdfffff ->
> > > > > > > >> >> 0x00fa000000
> > > > > > > >> >> [ 0.305285] rockchip-pcie f8000000.pcie: IO 0x00fbe00000..0x00fbefffff ->
> > > > > > > >> >> 0x00fbe00000
> > > > > > > >> >> [ 0.306201] rockchip-pcie f8000000.pcie: supply vpcie1v8 not found, using dummy
> > > > > > > >> >> regulator
> > > > > > > >> >> [ 0.306334] rockchip-pcie f8000000.pcie: supply vpcie0v9 not found, using dummy
> > > > > > > >> >> regulator
> > > > > > > >> >> [ 0.373705] rockchip-pcie f8000000.pcie: PCI host bridge to bus 0000:00
> > > > > > > >> >> [ 0.373730] pci_bus 0000:00: root bus resource [bus 00-1f]
> > > > > > > >> >> [ 0.373751] pci_bus 0000:00: root bus resource [mem 0xfa000000-0xfbdfffff 64bit]
> > > > > > > >> >> [ 0.373777] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus
> > > > > > > >> >> address [0xfbe00000-0xfbefffff])
> > > > > > > >> >> [ 0.373839] pci 0000:00:00.0: [1d87:0100] type 01 class 0x060400
> > > > > > > >> >> [ 0.373973] pci 0000:00:00.0: supports D1
> > > > > > > >> >> [ 0.373992] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
> > > > > > > >> >> [ 0.378518] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]),
> > > > > > > >> >> reconfiguring
> > > > > > > >> >> [ 0.378765] pci 0000:01:00.0: [144d:a808] type 00 class 0x010802
> > > > > > > >> >> [ 0.378869] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
> > > > > > > >> >> [ 0.379051] pci 0000:01:00.0: Max Payload Size set to 256 (was 128, max 256)
> > > > > > > >> >> [ 0.379661] pci 0000:01:00.0: 8.000 Gb/s available PCIe bandwidth, limited by
> > > > > > > >> >> 2.5 GT/s PCIe x4 link at 0000:00:00.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe
> > > > > > > >> >> x4 link)
> > > > > > > >> >> [ 0.393269] pci_bus 0000:01: busn_res: [bus 01-1f] end is updated to 01
> > > > > > > >> >> [ 0.393311] pci 0000:00:00.0: BAR 14: no space for [mem size 0x00100000]
> > > > > > > >> >> [ 0.393333] pci 0000:00:00.0: BAR 14: failed to assign [mem size 0x00100000]
> > > > > > > >> >> [ 0.393356] pci 0000:01:00.0: BAR 0: no space for [mem size 0x00004000 64bit]
> > > > > > > >> >> [ 0.393375] pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00004000 64bit]
> > > > > > > >> >> [ 0.393397] pci 0000:00:00.0: PCI bridge to [bus 01]
> > > > > > > >> >> [ 0.393839] pcieport 0000:00:00.0: PME: Signaling with IRQ 78
> > > > > > > >> >> [ 0.394165] pcieport 0000:00:00.0: AER: enabled with IRQ 78
> > > > > > > >> >> [..]
> > > > > > > >> >> to the commit 9d57e61bf723 ("of/pci: Add IORESOURCE_MEM_64 to
> > > > > > > >> >> resource flags for
> > > > > > > >> >> 64-bit memory addresses").
> > > > > > > >> >
> > > > > > > >> > FWFW, my hunch is that the host bridge advertising no 32-bit memory
> > > > > > > >> > resource, only only a single 64-bit non-prefetchable one (even though
> > > > > > > >> > it's entirely below 4GB) might be a bit weird and tripping something
> > > > > > > >> > up in the resource assignment code. It certainly seems like the thing
> > > > > > > >> > most directly related to the offending commit.
> > > > > > > >> >
> > > > > > > >> > I'd be tempted to try fiddling with that in the DT (i.e. changing
> > > > > > > >> > 0x83000000 to 0x82000000 in the PCIe node's "ranges" property) to see
> > > > > > > >> > if it makes any difference. Note that even if it helps, though, I
> > > > > > > >> > don't know whether that's the correct fix or just a bodge around a
> > > > > > > >> > corner-case bug somewhere in the resource code.
> > > > > > > >>
> > > > > > > >> From digging into this further the failure seems to be due to a mismatch
> > > > > > > >> of flags when allocating resources in pci_bus_alloc_from_region() -
> > > > > > > >>
> > > > > > > >> if ((res->flags ^ r->flags) & type_mask)
> > > > > > > >> continue;
> > > > > > > >>
> > > > > > > >> Though I am also not sure why the failure is only being reported on
> > > > > > > >> RK3399 - does a single 64-bit window have anything to do with it?
> > > > > > > >>
> > > > > > > >
> > > > > > > > The NVMe in the example exposes a single 64-bit non-prefetchable BAR.
> > > > > > > > Such BARs can not be allocated in a prefetchable host bridge window
> > > > > > > > (unlike the converse, i.e., allocating a prefetchable BAR in a
> > > > > > > > non-prefetchable host bridge window is fine)
> > > > > > > >
> > > > > > > > 64-bit non-prefetchable host bridge windows cannot be forwarded by PCI
> > > > > > > > to PCI bridges, they simply lack the BAR registers to describe them.
> > > > > > > > Therefore, non-prefetchable endpoint BARs (even 64-bit ones) need to
> > > > > > > > be carved out of a host bridge's non-prefetchable 32-bit window if
> > > > > > > > they need to pass through a bridge.
> > > > > > >
> > > > > > > Thank you for the explanation. I also looked at the PCI-to-PCI Bridge
> > > > > > > spec to understand where some of the limitations are coming from.
> > > > > > >
> > > > > > > > So the error seems to be here that the host bridge's 32-bit
> > > > > > > > non-prefetchable window has the 64-bit attribute set, even though it
> > > > > > > > resides below 4 GB entirely. I suppose that the resource allocation
> > > > > > > > could be made more forgiving (and it was in the past, before commit
> > > > > > > > 9d57e61bf723 was applied). However, I would strongly recommend not
> > > > > > > > deviating from common practice, and just describe the 32-bit
> > > > > > > > addressable non-prefetchable resource window as such.
> > > > > > >
> > > > > > > IIUC, the host bridge's configuration (64-bit on non-prefetchable
> > > > > > > window) is based on what the hardware advertises.
> > > > > > >
> > > > > >
> > > > > > What do you mean by 'what the hardware advertises'? The host bridge is
> > > > > > apparently configured to decode a 32-bit addressable window as MMIO,
> > > > > > and the question is why this window has the 64-bit attribute set in
> > > > > > the DT description.
> > > > > >
> > > > > > > Can you elaborate on what you have in mind to correct the
> > > > > > > non-prefetchable resource window? Are you thinking of adding a quirk
> > > > > > > somewhere to address this?
> > > > > > >
> > > > > >
> > > > > > No. Just fix the DT.
> > > > >
> > > > > Good Morning,
> > > > >
> > > > > I believe Robin is correct that there is more to this.
> > > > > While attempting to work out why dGPUs won't work with the rk356x
> > > > > series PCIe controllers, Christian König from the amd-gpu driver
> > > > > mailing list noticed the gpu was incorrectly allocated a 64bit
> > > > > non-prefetchable BAR which should instead be a 32 non-prefetchable
> > > > > BAR.
> > > > >
> > > >
> > > > This is due to the translation. For some reason, lspci translates the
> > > > BAR values to CPU addresses, but the PCI side addresses are within
> > > > 32-bits.
> > >
> > > The kernel log reports the same thing:
> > > [ 6.662141] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0fffffff
> > > 64bit pref]
> > > [ 6.662963] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x0001ffff 64bit]
> > >
> > > You are saying this is a display only issue?
> > >
> >
> > Yes. What do the 'root bus resource' log lines say for these regions?
> > Those should give you both the CPU address as well as the bus address.
>
> [ 6.673497] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
> (bus address [0x3f700000-0x3f7fffff])
> [ 6.674642] pci_bus 0000:00: root bus resource [mem
> 0x300000000-0x33f6fffff] (bus address [0x00000000-0x3f6fffff])
>
> I tweaked the original Rockchip values to place the non-prefetchable
> memory first with the configuration and io later in this boot.
>
> >
> >
> > > >
> > > > Are you sure the amdgpu driver can even deal with non-1:1 host bridges?
> > >
> > > I cannot answer this as I'm not an amdgpu dev.
> > >
> > > >
> > > > > The ranges currently set are:
> > > > > ranges = <0x81000000 0x0 0x00800000 0x3 0x00800000 0x0 0x00100000
> > > > > 0x82000000 0x0 0x00900000 0x3 0x00900000 0x0 0x3f700000>;
> > > > >
> > > >
> > > > So you have two ranges here.
> > >
> > > The IO and PCI memory ranges.
> > >
> > > There is a third range, the configuration range, which is defined in
> > > the reg block:
> > > <0x3 0x00000000 0x0 0x800000>
> > > All three are shared in the same 1GB window on the rk356x.
> > >
> >
> > But the reg block is not a resource window, it is a configuration
> > range to program the host bridge.
> >
> > > https://elixir.bootlin.com/linux/v5.13-rc3/source/Documentation/devicetree/bindings/pci/designware-pcie.txt#L12
> > >
> > > >
> > > > > but the final allocation was:
> > > > >
> > > > > lspci -v
> > > > > 00:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566
> > > > > (rev 01) (prog-if 00 [Normal decode])
> > > > > Flags: bus master, fast devsel, latency 0, IRQ 96
> > > > > Bus: primary=00, secondary=01, subordinate=ff, sec-latency=0
> > > > > I/O behind bridge: 00001000-00001fff [size=4K]
> > > > > Memory behind bridge: 00900000-009fffff [size=1M]
> > > > > Prefetchable memory behind bridge:
> > > > > 0000000010000000-000000001fffffff [size=256M]
> > > >
> > > > But the host bridge/root port decodes two disjoint regions??
> > > >
> > > > > Expansion ROM at 300a00000 [virtual] [disabled] [size=64K]
> > > > > Capabilities: [40] Power Management version 3
> > > > > Capabilities: [50] MSI: Enable+ Count=1/32 Maskable- 64bit+
> > > > > Capabilities: [70] Express Root Port (Slot-), MSI 00
> > > > > Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
> > > > > Capabilities: [100] Advanced Error Reporting
> > > > > Capabilities: [148] Secondary PCI Express
> > > > > Capabilities: [160] L1 PM Substates
> > > > > Capabilities: [170] Vendor Specific Information: ID=0002 Rev=4
> > > > > Len=100 <?>
> > > > > Kernel driver in use: pcieport
> > > > >
> > > > > 01:00.0 VGA compatible controller: Advanced Micro Devices, Inc.
> > > > > [AMD/ATI] Turks PRO [Radeon HD 7570] (prog-if 00 [VGA controller])
> > > > > Subsystem: Dell Turks PRO [Radeon HD 7570]
> > > > > Flags: bus master, fast devsel, latency 0, IRQ 95
> > > > > Memory at 310000000 (64-bit, prefetchable) [size=256M]
> > > > > Memory at 300900000 (64-bit, non-prefetchable) [size=128K]
> > > > > I/O ports at 1000 [size=256]
> > > > > Expansion ROM at 300920000 [disabled] [size=128K]
> > > > > Capabilities: [50] Power Management version 3
> > > > > Capabilities: [58] Express Legacy Endpoint, MSI 00
> > > > > Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
> > > > > Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1
> > > > > Len=010 <?>
> > > > > Capabilities: [150] Advanced Error Reporting
> > > > > Kernel driver in use: radeon
> > > > >
> > > > > 01:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Turks
> > > > > HDMI Audio [Radeon HD 6500/6600 / 6700M Series]
> > > > > Subsystem: Dell Turks HDMI Audio [Radeon HD 6500/6600 / 6700M Series]
> > > > > Flags: bus master, fast devsel, latency 0, IRQ 98
> > > > > Memory at 300940000 (64-bit, non-prefetchable) [size=16K]
> > > > > Capabilities: [50] Power Management version 3
> > > > > Capabilities: [58] Express Legacy Endpoint, MSI 00
> > > > > Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> > > > > Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1
> > > > > Len=010 <?>
> > > > > Capabilities: [150] Advanced Error Reporting
> > > > > Kernel driver in use: snd_hda_intel
> > > > >
> > > > > This will obviously clobber registers during writes.
> > > >
> > > > I don't follow. Which writes will clobber which registers, and how is
> > > > it obvious?
> > >
> > > Writing a 64 bit word into a 32 bit register will either clobber the
> > > next higher 32 bit register.
> > > Quoting Christian:
> > > "When you program a 32bit BAR as 64bit you overwrite the register behind
> > > the BAR address with the upper 32bits of the 64bit address value.
> > > So even if the allocation fits into 32bits, the extra register write
> > > will certainly put your device into a banana state."
> > >
> > > https://lists.freedesktop.org/archives/amd-gfx/2021-May/064232.html
> > >
> >
> > I seriously doubt that this is what is going on here.
> >
> > lspci -x will give you the bare BAR values - I suspect that those are
> > probably fine.
>
> lspci -x
> 00:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566 (rev 01)
> 00: 87 1d 66 35 07 05 10 40 01 00 04 06 00 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 01 ff 00 10 10 00 20
> 20: 00 10 00 10 01 00 f1 0f 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 5f 01 02 00
>
> 01:00.0 VGA compatible controller: Advanced Micro Devices, Inc.
> [AMD/ATI] Turks PRO [Radeon HD 7570]
> 00: 02 10 5d 67 07 00 10 20 00 00 00 03 00 00 80 00
> 10: 0c 00 00 00 00 00 00 00

This is a 64-bit prefetchable BAR programmed with bus address 0x0

> 04 00 00 10 00 00 00 00

This is a 64-bit non-prefetchable BAR programmed with bus address 0x1000_0000

(https://en.wikipedia.org/wiki/PCI_configuration_space describes the
meaning of the low order BAR bits)

> 20: 01 10 70 3f 00 00 00 00

This looks odd. This looks like a 32-bit MMIO address poked into a I/O BAR.


> 00 00 00 00 28 10 20 2b
> 30: 00 00 02 10 50 00 00 00 00 00 00 00 5f 01 00 00
>
> 01:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Turks
> HDMI Audio [Radeon HD 6500/6600 / 6700M Series]
> 00: 02 10 90 aa 06 00 10 20 00 00 03 04 00 00 80 00
> 10: 04 00 04 10 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 90 aa
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 02 00 00
>
> >
> >
> > > >
> > > > > Also, if <0x82000000> (32 bit) is changed to <0x83000000> (64 bit),
> > > > > most of the allocations for the dGPU fail due to no valid regions
> > > > > available.
> > > > >
> > > >
> > > > But wasn't the original problem that the resource window was 64-bit to
> > > > begin with? Are you sure we are talking about the same problem here?
> > >
> > > The rk3399 in the original report has a 32MB memory window in the
> > > upper end of the 4GB range.
> > > The rk356x has a similar layout, or it can use a 1GB window available
> > > at <0x3 0x00000000>.
> > > Rockchip's default windows are defined as 64bit.
> > >
> > > The rk3399 doesn't have enough space to reasonably define two windows,
> > > one 32bit, one 64bit, to work around an allocation bug.
> > > These are the defined regions in the rk3399:
> > > ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x1e00000>,
> > > <0x81000000 0x0 0xfbe00000 0x0 0xfbe00000 0x0 0x100000>;
> > >
> >
> > All you really need is a 32-bit non-prefetchable resource window: any
> > BAR can be allocated from that. A 64-bit BAR can carry a 32-bit number
> > (just add zeroes at the top), and a prefetchable BAR can happily live
> > in a non-prefetchable window, with a theoretical performance impact if
> > the OS actually does use different memory attributes for the
> > prefetchable window (but I don't think Linux ever handles it this way)
>
> So is the IO range necessary as well or will it be automatically
> allocated as well?
>

You need one I/O range and one 32-bit non-prefetchable MMIO window at
the very least, even though the I/O range is rarely used, even by
endpoints that expose I/O BARs.

The translation is tricky to get right, and confuses some drivers, so
it is better avoided if possible. If you do need translation, make
sure to translate in the right direction.

> >
> >
> > >
> > > >
> > > >
> > > > > >
> > > > > > > I am happy to put something together once I understand the preferred way
> > > > > > > to go about it.
> > > > > > >
> > > > > > > Thanks,
> > > > > > > Punit
> > > > > > >
> > > > > > > [...]
> > > > > > >
> > > > > >
> > > > > > _______________________________________________
> > > > > > Linux-rockchip mailing list
> > > > > > Linux-rockchip@xxxxxxxxxxxxxxxxxxx
> > > > > > http://lists.infradead.org/mailman/listinfo/linux-rockchip