RE: [PATCH net-next 4/6] r8152: support new chips

From: Hayes Wang
Date: Tue Apr 20 2021 - 03:00:54 EST


Jakub Kicinski <kuba@xxxxxxxxxx>
> Sent: Saturday, April 17, 2021 5:50 AM
> > + switch (tp->version) {
> > + case RTL_VER_10:
> > + data = ocp_reg_read(tp, 0xad40);
> > + data &= ~0x3ff;
> > + data |= BIT(7) | BIT(2);
> > + ocp_reg_write(tp, 0xad40, data);
> > +
> > + data = ocp_reg_read(tp, 0xad4e);
> > + data |= BIT(4);
> > + ocp_reg_write(tp, 0xad4e, data);
> > + data = ocp_reg_read(tp, 0xad16);
> > + data &= ~0x3ff;
> > + data |= 0x6;
> > + ocp_reg_write(tp, 0xad16, data);
> > + data = ocp_reg_read(tp, 0xad32);
> > + data &= ~0x3f;
> > + data |= 6;
> > + ocp_reg_write(tp, 0xad32, data);
> > + data = ocp_reg_read(tp, 0xac08);
> > + data &= ~(BIT(12) | BIT(8));
> > + ocp_reg_write(tp, 0xac08, data);
> > + data = ocp_reg_read(tp, 0xac8a);
> > + data |= BIT(12) | BIT(13) | BIT(14);
> > + data &= ~BIT(15);
> > + ocp_reg_write(tp, 0xac8a, data);
> > + data = ocp_reg_read(tp, 0xad18);
> > + data |= BIT(10);
> > + ocp_reg_write(tp, 0xad18, data);
> > + data = ocp_reg_read(tp, 0xad1a);
> > + data |= 0x3ff;
> > + ocp_reg_write(tp, 0xad1a, data);
> > + data = ocp_reg_read(tp, 0xad1c);
> > + data |= 0x3ff;
> > + ocp_reg_write(tp, 0xad1c, data);
> > +
> > + data = sram_read(tp, 0x80ea);
> > + data &= ~0xff00;
> > + data |= 0xc400;
> > + sram_write(tp, 0x80ea, data);
> > + data = sram_read(tp, 0x80eb);
> > + data &= ~0x0700;
> > + data |= 0x0300;
> > + sram_write(tp, 0x80eb, data);
> > + data = sram_read(tp, 0x80f8);
> > + data &= ~0xff00;
> > + data |= 0x1c00;
> > + sram_write(tp, 0x80f8, data);
> > + data = sram_read(tp, 0x80f1);
> > + data &= ~0xff00;
> > + data |= 0x3000;
> > + sram_write(tp, 0x80f1, data);

These are the parameters of PHY.
Some are used for speed down about power saving.
And some are used for performance.

> > + switch (tp->version) {
> > + case RTL_VER_12:
> > + ocp_reg_write(tp, 0xbf86, 0x9000);
> > + data = ocp_reg_read(tp, 0xc402);
> > + data |= BIT(10);
> > + ocp_reg_write(tp, 0xc402, data);
> > + data &= ~BIT(10);
> > + ocp_reg_write(tp, 0xc402, data);
> > + ocp_reg_write(tp, 0xbd86, 0x1010);
> > + ocp_reg_write(tp, 0xbd88, 0x1010);
> > + data = ocp_reg_read(tp, 0xbd4e);
> > + data &= ~(BIT(10) | BIT(11));
> > + data |= BIT(11);
> > + ocp_reg_write(tp, 0xbd4e, data);
> > + data = ocp_reg_read(tp, 0xbf46);
> > + data &= ~0xf00;
> > + data |= 0x700;
> > + ocp_reg_write(tp, 0xbf46, data);

These are used to adjust the clock of GPHY.
It influences the linking.

> > + data = r8153_phy_status(tp, 0);
> > + switch (data) {
> > + case PHY_STAT_EXT_INIT:
> > + rtl8152_apply_firmware(tp, true);
> > +
> > + data = ocp_reg_read(tp, 0xa466);
> > + data &= ~BIT(0);
> > + ocp_reg_write(tp, 0xa466, data);

These let the PHY exit PHY_STAT_EXT_INIT state.

> What are all these magic constants? :(

I think it is difficult for me to make all magic values meaningful.
The PHY setting is very complex. Only PHY engineers know
what are the settings mean.

> > @@ -6878,7 +8942,11 @@ static int rtl8152_probe(struct usb_interface
> *intf,
> > set_ethernet_addr(tp);
> >
> > usb_set_intfdata(intf, tp);
> > - netif_napi_add(netdev, &tp->napi, r8152_poll, RTL8152_NAPI_WEIGHT);
> > +
> > + if (tp->support_2500full)
> > + netif_napi_add(netdev, &tp->napi, r8152_poll, 256);
>
> why 256? We have 100G+ drivers all using 64 what's special here?
>
> > + else
> > + netif_napi_add(netdev, &tp->napi, r8152_poll, 64);

We test 2.5G Ethernet on some embedded platform.
And we find 64 is not large enough, and the performance
couldn't reach 2.5 G bits/s.

Best Regards,
Hayes