Re: [RFC net-next] net: dsa: rtl8366rb: support bridge offloading

[Florian Fainelli]

On 2/23/2021 10:12 PM, DENG Qingfang wrote:
> Use port isolation registers to configure bridge offloading.
> Remove the VLAN init, as we have proper CPU tag and bridge offloading
> support now.
> 
> Signed-off-by: DENG Qingfang <dqfext@xxxxxxxxx>
> ---
> This is not tested, as I don't have a RTL8366RB board. And I think there
> is potential race condition in port_bridge_{join,leave}.
> 
>  drivers/net/dsa/rtl8366rb.c | 73 ++++++++++++++++++++++++++++++++++---
>  1 file changed, 67 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/net/dsa/rtl8366rb.c b/drivers/net/dsa/rtl8366rb.c
> index a89093bc6c6a..9f6e2b361216 100644
> --- a/drivers/net/dsa/rtl8366rb.c
> +++ b/drivers/net/dsa/rtl8366rb.c
> @@ -300,6 +300,12 @@
>  #define RTL8366RB_INTERRUPT_STATUS_REG	0x0442
>  #define RTL8366RB_NUM_INTERRUPT		14 /* 0..13 */
>  
> +/* Port isolation registers */
> +#define RTL8366RB_PORT_ISO_BASE		0x0F08
> +#define RTL8366RB_PORT_ISO(pnum)	(RTL8366RB_PORT_ISO_BASE + (pnum))
> +#define RTL8366RB_PORT_ISO_EN		BIT(0)
> +#define RTL8366RB_PORT_ISO_PORTS_MASK	GENMASK(7, 1)
> +
>  /* bits 0..5 enable force when cleared */
>  #define RTL8366RB_MAC_FORCE_CTRL_REG	0x0F11
>  
> @@ -835,6 +841,15 @@ static int rtl8366rb_setup(struct dsa_switch *ds)
>  	if (ret)
>  		return ret;
>  
> +	/* Isolate user ports */
> +	for (i = 0; i < RTL8366RB_PORT_NUM_CPU; i++) {
> +		ret = regmap_write(smi->map, RTL8366RB_PORT_ISO(i),
> +				   RTL8366RB_PORT_ISO_EN |
> +				   BIT(RTL8366RB_PORT_NUM_CPU + 1));
> +		if (ret)
> +			return ret;
> +	}
> +
>  	/* Set up the "green ethernet" feature */
>  	ret = rtl8366rb_jam_table(rtl8366rb_green_jam,
>  				  ARRAY_SIZE(rtl8366rb_green_jam), smi, false);
> @@ -963,10 +978,6 @@ static int rtl8366rb_setup(struct dsa_switch *ds)
>  			return ret;
>  	}
>  
> -	ret = rtl8366_init_vlan(smi);
> -	if (ret)
> -		return ret;
> -
>  	ret = rtl8366rb_setup_cascaded_irq(smi);
>  	if (ret)
>  		dev_info(smi->dev, "no interrupt support\n");
> @@ -977,8 +988,6 @@ static int rtl8366rb_setup(struct dsa_switch *ds)
>  		return -ENODEV;
>  	}
>  
> -	ds->configure_vlan_while_not_filtering = false;

If you have a configuration with ports that are part of a bridge with
VLAN filtering enabled, what happens to the standalone ports, are they a
member of a default VLAN entry still?
-- 
Florian