Re: [PATCH 1/2] uas: revert from scsi_add_host_with_dma() to scsi_add_host()

[Tom Yan]

Hmm, I wonder if I/we wrongly assumed that the dma_dev used for the
hw_max_sectors clamping in __scsi_init_queue() is wrong.

So instead of adding a fallback else-clause here or using "sysdev" as
dma_dev like in the current upstream code, maybe we should actually do
a three-way min: the "changed" hw_max_sectors, dma_max_mapping_size of
dma_dev("dev") and dma_max_mapping_size of sysdev...?

On Mon, 30 Nov 2020 at 17:48, Hans de Goede <hdegoede@xxxxxxxxxx> wrote:
>
> Hi,
>
> On 11/28/20 4:48 PM, Tom Yan wrote:
> > Apparently the former (with the chosen dma_dev) may cause problem in certain
> > case (e.g. where thunderbolt dock and intel iommu are involved). The error
> > observed was:
> >
> > XHCI swiotlb buffer is full / DMAR: Device bounce map failed
> >
> > For now we retain the clamp for hw_max_sectors against the dma_max_mapping_size.
> > Since the device/size for the clamp that is applied when the scsi request queue
> > is initialized/allocated is different than the one used here, we invalidate the
> > early clamping by making a fallback blk_queue_max_hw_sectors() call.
> >
> > Signed-off-by: Tom Yan <tom.ty89@xxxxxxxxx>
>
> I can confirm that this fixes the network performance on a Lenovo Thunderbolt
> dock generation 2, which uses an USB attach NIC.
>
> With this patch added on top of 5.10-rc5 scp performance to another machine
> on the local gbit LAN goes back from the regressed 1 MB/s to its original 100MB/s
> as it should be:
>
> Tested-by: Hans de Goede <hdegoede@xxxxxxxxxx>
>
> Regards,
>
> Hans
>
>
> > ---
> >  drivers/usb/storage/uas.c | 11 +++++++----
> >  1 file changed, 7 insertions(+), 4 deletions(-)
> >
> > diff --git a/drivers/usb/storage/uas.c b/drivers/usb/storage/uas.c
> > index c8a577309e8f..5db1325cea20 100644
> > --- a/drivers/usb/storage/uas.c
> > +++ b/drivers/usb/storage/uas.c
> > @@ -843,18 +843,21 @@ static int uas_slave_alloc(struct scsi_device *sdev)
> >  static int uas_slave_configure(struct scsi_device *sdev)
> >  {
> >       struct uas_dev_info *devinfo = sdev->hostdata;
> > -     struct device *dev = sdev->host->dma_dev;
> > +     struct usb_device *udev = devinfo->udev;
> >
> >       if (devinfo->flags & US_FL_MAX_SECTORS_64)
> >               blk_queue_max_hw_sectors(sdev->request_queue, 64);
> >       else if (devinfo->flags & US_FL_MAX_SECTORS_240)
> >               blk_queue_max_hw_sectors(sdev->request_queue, 240);
> > -     else if (devinfo->udev->speed >= USB_SPEED_SUPER)
> > +     else if (udev->speed >= USB_SPEED_SUPER)
> >               blk_queue_max_hw_sectors(sdev->request_queue, 2048);
> > +     else
> > +             blk_queue_max_hw_sectors(sdev->request_queue,
> > +                                      SCSI_DEFAULT_MAX_SECTORS);
> >
> >       blk_queue_max_hw_sectors(sdev->request_queue,
> >               min_t(size_t, queue_max_hw_sectors(sdev->request_queue),
> > -                   dma_max_mapping_size(dev) >> SECTOR_SHIFT));
> > +                   dma_max_mapping_size(udev->bus->sysdev) >> SECTOR_SHIFT));
> >
> >       if (devinfo->flags & US_FL_NO_REPORT_OPCODES)
> >               sdev->no_report_opcodes = 1;
> > @@ -1040,7 +1043,7 @@ static int uas_probe(struct usb_interface *intf, const struct usb_device_id *id)
> >       shost->can_queue = devinfo->qdepth - 2;
> >
> >       usb_set_intfdata(intf, shost);
> > -     result = scsi_add_host_with_dma(shost, &intf->dev, udev->bus->sysdev);
> > +     result = scsi_add_host(shost, &intf->dev);
> >       if (result)
> >               goto free_streams;
> >
> >
>