Re: [PATCH v4] hwmon (pmbus/max20730): add device monitoring via debugfs

From: Guenter Roeck
Date: Sun Oct 04 2020 - 11:54:14 EST


On Tue, Sep 22, 2020 at 07:15:38PM +0000, Ugur Usug wrote:
> Add debugfs interface support for accessing device specific registers (MFR_VOUT_MIN,
> MFR_DEVSET1 and MFR_DEVSET2) and others including OPERATION, ON_OFF_CONFIG,
> SMB_ALERT_MASK, VOUT_MODE, VOUT_COMMAND and VOUT_MAX.
>
> This patch changes following items in max20730_debugfs_read():
> - the EINVAL returns to "Invalid" or "Not supported"
> - strcpy() and strnlen() calls to strlcpy() calls
> - VOUT_MODE, VOUT_COMMAND and VOUT_MAX raw outputs to unit volts
> - terminating '\0' characters to the simple_read_from_buffer() return
>
> Signed-off-by: Ugur Usug <ugur.usug@xxxxxxxxxxxxxxxxxxx>

Applied.

Thanks,
Guenter

> ---
> drivers/hwmon/pmbus/max20730.c | 363 ++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 362 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/hwmon/pmbus/max20730.c b/drivers/hwmon/pmbus/max20730.c
> index a151a2b..3175c9b 100644
> --- a/drivers/hwmon/pmbus/max20730.c
> +++ b/drivers/hwmon/pmbus/max20730.c
> @@ -8,6 +8,7 @@
> */
>
> #include <linux/bits.h>
> +#include <linux/debugfs.h>
> #include <linux/err.h>
> #include <linux/i2c.h>
> #include <linux/init.h>
> @@ -26,16 +27,367 @@ enum chips {
> max20743
> };
>
> +enum {
> + MAX20730_DEBUGFS_VOUT_MIN = 0,
> + MAX20730_DEBUGFS_FREQUENCY,
> + MAX20730_DEBUGFS_PG_DELAY,
> + MAX20730_DEBUGFS_INTERNAL_GAIN,
> + MAX20730_DEBUGFS_BOOT_VOLTAGE,
> + MAX20730_DEBUGFS_OUT_V_RAMP_RATE,
> + MAX20730_DEBUGFS_OC_PROTECT_MODE,
> + MAX20730_DEBUGFS_SS_TIMING,
> + MAX20730_DEBUGFS_IMAX,
> + MAX20730_DEBUGFS_OPERATION,
> + MAX20730_DEBUGFS_ON_OFF_CONFIG,
> + MAX20730_DEBUGFS_SMBALERT_MASK,
> + MAX20730_DEBUGFS_VOUT_MODE,
> + MAX20730_DEBUGFS_VOUT_COMMAND,
> + MAX20730_DEBUGFS_VOUT_MAX,
> + MAX20730_DEBUGFS_NUM_ENTRIES
> +};
> +
> struct max20730_data {
> enum chips id;
> struct pmbus_driver_info info;
> struct mutex lock; /* Used to protect against parallel writes */
> u16 mfr_devset1;
> + u16 mfr_devset2;
> + u16 mfr_voutmin;
> };
>
> #define to_max20730_data(x) container_of(x, struct max20730_data, info)
>
> +#define VOLT_FROM_REG(val) DIV_ROUND_CLOSEST((val), 1 << 9)
> +
> +#define PMBUS_SMB_ALERT_MASK 0x1B
> +
> +#define MAX20730_MFR_VOUT_MIN 0xd1
> #define MAX20730_MFR_DEVSET1 0xd2
> +#define MAX20730_MFR_DEVSET2 0xd3
> +
> +#define MAX20730_MFR_VOUT_MIN_MASK GENMASK(9, 0)
> +#define MAX20730_MFR_VOUT_MIN_BIT_POS 0
> +
> +#define MAX20730_MFR_DEVSET1_RGAIN_MASK (BIT(13) | BIT(14))
> +#define MAX20730_MFR_DEVSET1_OTP_MASK (BIT(11) | BIT(12))
> +#define MAX20730_MFR_DEVSET1_VBOOT_MASK (BIT(8) | BIT(9))
> +#define MAX20730_MFR_DEVSET1_OCP_MASK (BIT(5) | BIT(6))
> +#define MAX20730_MFR_DEVSET1_FSW_MASK GENMASK(4, 2)
> +#define MAX20730_MFR_DEVSET1_TSTAT_MASK (BIT(0) | BIT(1))
> +
> +#define MAX20730_MFR_DEVSET1_RGAIN_BIT_POS 13
> +#define MAX20730_MFR_DEVSET1_OTP_BIT_POS 11
> +#define MAX20730_MFR_DEVSET1_VBOOT_BIT_POS 8
> +#define MAX20730_MFR_DEVSET1_OCP_BIT_POS 5
> +#define MAX20730_MFR_DEVSET1_FSW_BIT_POS 2
> +#define MAX20730_MFR_DEVSET1_TSTAT_BIT_POS 0
> +
> +#define MAX20730_MFR_DEVSET2_IMAX_MASK GENMASK(10, 8)
> +#define MAX20730_MFR_DEVSET2_VRATE (BIT(6) | BIT(7))
> +#define MAX20730_MFR_DEVSET2_OCPM_MASK BIT(5)
> +#define MAX20730_MFR_DEVSET2_SS_MASK (BIT(0) | BIT(1))
> +
> +#define MAX20730_MFR_DEVSET2_IMAX_BIT_POS 8
> +#define MAX20730_MFR_DEVSET2_VRATE_BIT_POS 6
> +#define MAX20730_MFR_DEVSET2_OCPM_BIT_POS 5
> +#define MAX20730_MFR_DEVSET2_SS_BIT_POS 0
> +
> +#define DEBUG_FS_DATA_MAX 16
> +
> +struct max20730_debugfs_data {
> + struct i2c_client *client;
> + int debugfs_entries[MAX20730_DEBUGFS_NUM_ENTRIES];
> +};
> +
> +#define to_psu(x, y) container_of((x), \
> + struct max20730_debugfs_data, debugfs_entries[(y)])
> +
> +#ifdef CONFIG_DEBUG_FS
> +static ssize_t max20730_debugfs_read(struct file *file, char __user *buf,
> + size_t count, loff_t *ppos)
> +{
> + int ret, len;
> + int *idxp = file->private_data;
> + int idx = *idxp;
> + struct max20730_debugfs_data *psu = to_psu(idxp, idx);
> + const struct pmbus_driver_info *info;
> + const struct max20730_data *data;
> + char tbuf[DEBUG_FS_DATA_MAX] = { 0 };
> + u16 val;
> +
> + info = pmbus_get_driver_info(psu->client);
> + data = to_max20730_data(info);
> +
> + switch (idx) {
> + case MAX20730_DEBUGFS_VOUT_MIN:
> + ret = VOLT_FROM_REG(data->mfr_voutmin * 10000);
> + len = snprintf(tbuf, DEBUG_FS_DATA_MAX, "%d.%d\n",
> + ret / 10000, ret % 10000);
> + break;
> + case MAX20730_DEBUGFS_FREQUENCY:
> + val = (data->mfr_devset1 & MAX20730_MFR_DEVSET1_FSW_MASK)
> + >> MAX20730_MFR_DEVSET1_FSW_BIT_POS;
> +
> + if (val == 0)
> + ret = 400;
> + else if (val == 1)
> + ret = 500;
> + else if (val == 2 || val == 3)
> + ret = 600;
> + else if (val == 4)
> + ret = 700;
> + else if (val == 5)
> + ret = 800;
> + else
> + ret = 900;
> + len = snprintf(tbuf, DEBUG_FS_DATA_MAX, "%d\n", ret);
> + break;
> + case MAX20730_DEBUGFS_PG_DELAY:
> + val = (data->mfr_devset1 & MAX20730_MFR_DEVSET1_TSTAT_MASK)
> + >> MAX20730_MFR_DEVSET1_TSTAT_BIT_POS;
> +
> + if (val == 0)
> + len = strlcpy(tbuf, "2000\n", DEBUG_FS_DATA_MAX);
> + else if (val == 1)
> + len = strlcpy(tbuf, "125\n", DEBUG_FS_DATA_MAX);
> + else if (val == 2)
> + len = strlcpy(tbuf, "62.5\n", DEBUG_FS_DATA_MAX);
> + else
> + len = strlcpy(tbuf, "32\n", DEBUG_FS_DATA_MAX);
> + break;
> + case MAX20730_DEBUGFS_INTERNAL_GAIN:
> + val = (data->mfr_devset1 & MAX20730_MFR_DEVSET1_RGAIN_MASK)
> + >> MAX20730_MFR_DEVSET1_RGAIN_BIT_POS;
> +
> + if (data->id == max20734) {
> + /* AN6209 */
> + if (val == 0)
> + len = strlcpy(tbuf, "0.8\n", DEBUG_FS_DATA_MAX);
> + else if (val == 1)
> + len = strlcpy(tbuf, "3.2\n", DEBUG_FS_DATA_MAX);
> + else if (val == 2)
> + len = strlcpy(tbuf, "1.6\n", DEBUG_FS_DATA_MAX);
> + else
> + len = strlcpy(tbuf, "6.4\n", DEBUG_FS_DATA_MAX);
> + } else if (data->id == max20730 || data->id == max20710) {
> + /* AN6042 or AN6140 */
> + if (val == 0)
> + len = strlcpy(tbuf, "0.9\n", DEBUG_FS_DATA_MAX);
> + else if (val == 1)
> + len = strlcpy(tbuf, "3.6\n", DEBUG_FS_DATA_MAX);
> + else if (val == 2)
> + len = strlcpy(tbuf, "1.8\n", DEBUG_FS_DATA_MAX);
> + else
> + len = strlcpy(tbuf, "7.2\n", DEBUG_FS_DATA_MAX);
> + } else if (data->id == max20743) {
> + /* AN6042 */
> + if (val == 0)
> + len = strlcpy(tbuf, "0.45\n", DEBUG_FS_DATA_MAX);
> + else if (val == 1)
> + len = strlcpy(tbuf, "1.8\n", DEBUG_FS_DATA_MAX);
> + else if (val == 2)
> + len = strlcpy(tbuf, "0.9\n", DEBUG_FS_DATA_MAX);
> + else
> + len = strlcpy(tbuf, "3.6\n", DEBUG_FS_DATA_MAX);
> + } else {
> + len = strlcpy(tbuf, "Not supported\n", DEBUG_FS_DATA_MAX);
> + }
> + break;
> + case MAX20730_DEBUGFS_BOOT_VOLTAGE:
> + val = (data->mfr_devset1 & MAX20730_MFR_DEVSET1_VBOOT_MASK)
> + >> MAX20730_MFR_DEVSET1_VBOOT_BIT_POS;
> +
> + if (val == 0)
> + len = strlcpy(tbuf, "0.6484\n", DEBUG_FS_DATA_MAX);
> + else if (val == 1)
> + len = strlcpy(tbuf, "0.8984\n", DEBUG_FS_DATA_MAX);
> + else if (val == 2)
> + len = strlcpy(tbuf, "1.0\n", DEBUG_FS_DATA_MAX);
> + else
> + len = strlcpy(tbuf, "Invalid\n", DEBUG_FS_DATA_MAX);
> + break;
> + case MAX20730_DEBUGFS_OUT_V_RAMP_RATE:
> + val = (data->mfr_devset2 & MAX20730_MFR_DEVSET2_VRATE)
> + >> MAX20730_MFR_DEVSET2_VRATE_BIT_POS;
> +
> + if (val == 0)
> + len = strlcpy(tbuf, "4\n", DEBUG_FS_DATA_MAX);
> + else if (val == 1)
> + len = strlcpy(tbuf, "2\n", DEBUG_FS_DATA_MAX);
> + else if (val == 2)
> + len = strlcpy(tbuf, "1\n", DEBUG_FS_DATA_MAX);
> + else
> + len = strlcpy(tbuf, "Invalid\n", DEBUG_FS_DATA_MAX);
> + break;
> + case MAX20730_DEBUGFS_OC_PROTECT_MODE:
> + ret = (data->mfr_devset2 & MAX20730_MFR_DEVSET2_OCPM_MASK)
> + >> MAX20730_MFR_DEVSET2_OCPM_BIT_POS;
> + len = snprintf(tbuf, DEBUG_FS_DATA_MAX, "%d\n", ret);
> + break;
> + case MAX20730_DEBUGFS_SS_TIMING:
> + val = (data->mfr_devset2 & MAX20730_MFR_DEVSET2_SS_MASK)
> + >> MAX20730_MFR_DEVSET2_SS_BIT_POS;
> +
> + if (val == 0)
> + len = strlcpy(tbuf, "0.75\n", DEBUG_FS_DATA_MAX);
> + else if (val == 1)
> + len = strlcpy(tbuf, "1.5\n", DEBUG_FS_DATA_MAX);
> + else if (val == 2)
> + len = strlcpy(tbuf, "3\n", DEBUG_FS_DATA_MAX);
> + else
> + len = strlcpy(tbuf, "6\n", DEBUG_FS_DATA_MAX);
> + break;
> + case MAX20730_DEBUGFS_IMAX:
> + ret = (data->mfr_devset2 & MAX20730_MFR_DEVSET2_IMAX_MASK)
> + >> MAX20730_MFR_DEVSET2_IMAX_BIT_POS;
> + len = snprintf(tbuf, DEBUG_FS_DATA_MAX, "%d\n", ret);
> + break;
> + case MAX20730_DEBUGFS_OPERATION:
> + ret = i2c_smbus_read_byte_data(psu->client, PMBUS_OPERATION);
> + if (ret < 0)
> + return ret;
> + len = snprintf(tbuf, DEBUG_FS_DATA_MAX, "%d\n", ret);
> + break;
> + case MAX20730_DEBUGFS_ON_OFF_CONFIG:
> + ret = i2c_smbus_read_byte_data(psu->client, PMBUS_ON_OFF_CONFIG);
> + if (ret < 0)
> + return ret;
> + len = snprintf(tbuf, DEBUG_FS_DATA_MAX, "%d\n", ret);
> + break;
> + case MAX20730_DEBUGFS_SMBALERT_MASK:
> + ret = i2c_smbus_read_word_data(psu->client,
> + PMBUS_SMB_ALERT_MASK);
> + if (ret < 0)
> + return ret;
> + len = snprintf(tbuf, DEBUG_FS_DATA_MAX, "%d\n", ret);
> + break;
> + case MAX20730_DEBUGFS_VOUT_MODE:
> + ret = i2c_smbus_read_byte_data(psu->client, PMBUS_VOUT_MODE);
> + if (ret < 0)
> + return ret;
> + len = snprintf(tbuf, DEBUG_FS_DATA_MAX, "%d\n", ret);
> + break;
> + case MAX20730_DEBUGFS_VOUT_COMMAND:
> + ret = i2c_smbus_read_word_data(psu->client, PMBUS_VOUT_COMMAND);
> + if (ret < 0)
> + return ret;
> +
> + ret = VOLT_FROM_REG(ret * 10000);
> + len = snprintf(tbuf, DEBUG_FS_DATA_MAX,
> + "%d.%d\n", ret / 10000, ret % 10000);
> + break;
> + case MAX20730_DEBUGFS_VOUT_MAX:
> + ret = i2c_smbus_read_word_data(psu->client, PMBUS_VOUT_MAX);
> + if (ret < 0)
> + return ret;
> +
> + ret = VOLT_FROM_REG(ret * 10000);
> + len = snprintf(tbuf, DEBUG_FS_DATA_MAX,
> + "%d.%d\n", ret / 10000, ret % 10000);
> + break;
> + default:
> + len = strlcpy(tbuf, "Invalid\n", DEBUG_FS_DATA_MAX);
> + }
> +
> + return simple_read_from_buffer(buf, count, ppos, tbuf, len);
> +}
> +
> +static const struct file_operations max20730_fops = {
> + .llseek = noop_llseek,
> + .read = max20730_debugfs_read,
> + .write = NULL,
> + .open = simple_open,
> +};
> +
> +static int max20730_init_debugfs(struct i2c_client *client,
> + struct max20730_data *data)
> +{
> + int ret, i;
> + struct dentry *debugfs;
> + struct dentry *max20730_dir;
> + struct max20730_debugfs_data *psu;
> +
> + ret = i2c_smbus_read_word_data(client, MAX20730_MFR_DEVSET2);
> + if (ret < 0)
> + return ret;
> + data->mfr_devset2 = ret;
> +
> + ret = i2c_smbus_read_word_data(client, MAX20730_MFR_VOUT_MIN);
> + if (ret < 0)
> + return ret;
> + data->mfr_voutmin = ret;
> +
> + psu = devm_kzalloc(&client->dev, sizeof(*psu), GFP_KERNEL);
> + if (!psu)
> + return -ENOMEM;
> + psu->client = client;
> +
> + debugfs = pmbus_get_debugfs_dir(client);
> + if (!debugfs)
> + return -ENOENT;
> +
> + max20730_dir = debugfs_create_dir(client->name, debugfs);
> + if (!max20730_dir)
> + return -ENOENT;
> +
> + for (i = 0; i < MAX20730_DEBUGFS_NUM_ENTRIES; ++i)
> + psu->debugfs_entries[i] = i;
> +
> + debugfs_create_file("vout_min", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_VOUT_MIN],
> + &max20730_fops);
> + debugfs_create_file("frequency", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_FREQUENCY],
> + &max20730_fops);
> + debugfs_create_file("power_good_delay", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_PG_DELAY],
> + &max20730_fops);
> + debugfs_create_file("internal_gain", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_INTERNAL_GAIN],
> + &max20730_fops);
> + debugfs_create_file("boot_voltage", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_BOOT_VOLTAGE],
> + &max20730_fops);
> + debugfs_create_file("out_voltage_ramp_rate", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_OUT_V_RAMP_RATE],
> + &max20730_fops);
> + debugfs_create_file("oc_protection_mode", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_OC_PROTECT_MODE],
> + &max20730_fops);
> + debugfs_create_file("soft_start_timing", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_SS_TIMING],
> + &max20730_fops);
> + debugfs_create_file("imax", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_IMAX],
> + &max20730_fops);
> + debugfs_create_file("operation", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_OPERATION],
> + &max20730_fops);
> + debugfs_create_file("on_off_config", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_ON_OFF_CONFIG],
> + &max20730_fops);
> + debugfs_create_file("smbalert_mask", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_SMBALERT_MASK],
> + &max20730_fops);
> + debugfs_create_file("vout_mode", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_VOUT_MODE],
> + &max20730_fops);
> + debugfs_create_file("vout_command", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_VOUT_COMMAND],
> + &max20730_fops);
> + debugfs_create_file("vout_max", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_VOUT_MAX],
> + &max20730_fops);
> +
> + return 0;
> +}
> +#else
> +static int max20730_init_debugfs(struct i2c_client *client,
> + struct max20730_data *data)
> +{
> + return 0;
> +}
> +#endif /* CONFIG_DEBUG_FS */
>
> /*
> * Convert discreet value to direct data format. Strictly speaking, all passed
> @@ -370,7 +722,16 @@ static int max20730_probe(struct i2c_client *client,
> return ret;
> data->mfr_devset1 = ret;
>
> - return pmbus_do_probe(client, id, &data->info);
> + ret = pmbus_do_probe(client, id, &data->info);
> + if (ret < 0)
> + return ret;
> +
> + ret = max20730_init_debugfs(client, data);
> + if (ret)
> + dev_warn(dev, "Failed to register debugfs: %d\n",
> + ret);
> +
> + return 0;
> }
>
> static const struct i2c_device_id max20730_id[] = {