Re: [PATCH v2] Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 support

[Marcel Holtmann]

Hi Rocky,

> This patch add support for WCN6855 i.e. patch and nvm download
> support.
> 
> Signed-off-by: Rocky Liao <rjliao@xxxxxxxxxxxxxx>
> ---
> drivers/bluetooth/btusb.c | 50 ++++++++++++++++++++++++++++++++++-----
> 1 file changed, 44 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
> index fe80588c7bd3..789e8d5e829e 100644
> --- a/drivers/bluetooth/btusb.c
> +++ b/drivers/bluetooth/btusb.c
> @@ -59,6 +59,7 @@ static struct usb_driver btusb_driver;
> #define BTUSB_MEDIATEK		0x200000
> #define BTUSB_WIDEBAND_SPEECH	0x400000
> #define BTUSB_VALID_LE_STATES   0x800000
> +#define BTUSB_QCA_WCN6855	0x1000000
> 
> static const struct usb_device_id btusb_table[] = {
> 	/* Generic Bluetooth USB device */
> @@ -273,6 +274,10 @@ static const struct usb_device_id blacklist_table[] = {
> 	{ USB_DEVICE(0x13d3, 0x3496), .driver_info = BTUSB_QCA_ROME },
> 	{ USB_DEVICE(0x13d3, 0x3501), .driver_info = BTUSB_QCA_ROME },
> 
> +	/* QCA WCN6855 chipset */
> +	{ USB_DEVICE(0x0cf3, 0xe600), .driver_info = BTUSB_QCA_WCN6855 |
> +						     BTUSB_WIDEBAND_SPEECH },
> +
> 	/* Broadcom BCM2035 */
> 	{ USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
> 	{ USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU },
> @@ -3391,6 +3396,26 @@ static int btusb_set_bdaddr_ath3012(struct hci_dev *hdev,
> 	return 0;
> }
> 
> +static int btusb_set_bdaddr_wcn6855(struct hci_dev *hdev,
> +				const bdaddr_t *bdaddr)
> +{
> +	struct sk_buff *skb;
> +	u8 buf[6];
> +	long ret;
> +
> +	memcpy(buf, bdaddr, sizeof(bdaddr_t));
> +
> +	skb = __hci_cmd_sync(hdev, 0xfc14, sizeof(buf), buf, HCI_INIT_TIMEOUT);
> +	if (IS_ERR(skb)) {
> +		ret = PTR_ERR(skb);
> +		bt_dev_err(hdev, "Change address command failed (%ld)", ret);
> +		return ret;
> +	}
> +	kfree_skb(skb);
> +
> +	return 0;
> +}
> +
> #define QCA_DFU_PACKET_LEN	4096
> 
> #define QCA_GET_TARGET_VERSION	0x09
> @@ -3428,6 +3453,8 @@ static const struct qca_device_info qca_devices_table[] = {
> 	{ 0x00000201, 28, 4, 18 }, /* Rome 2.1 */
> 	{ 0x00000300, 28, 4, 18 }, /* Rome 3.0 */
> 	{ 0x00000302, 28, 4, 18 }, /* Rome 3.2 */
> +	{ 0x00130100, 40, 4, 18 }, /* WCN6855 1.0 */
> +	{ 0x00130200, 40, 4, 18 }  /* WCN6855 2.0 */
> };
> 
> static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request,
> @@ -3529,8 +3556,8 @@ static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev,
> {
> 	struct qca_rampatch_version *rver;
> 	const struct firmware *fw;
> -	u32 ver_rom, ver_patch;
> -	u16 rver_rom, rver_patch;
> +	u32 ver_rom, ver_patch, rver_rom;
> +	u16 rver_rom_low, rver_rom_high, rver_patch;
> 	char fwname[64];
> 	int err;
> 
> @@ -3549,9 +3576,16 @@ static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev,
> 	bt_dev_info(hdev, "using rampatch file: %s", fwname);
> 
> 	rver = (struct qca_rampatch_version *)(fw->data + info->ver_offset);
> -	rver_rom = le16_to_cpu(rver->rom_version);
> +	rver_rom_low = le16_to_cpu(rver->rom_version);
> 	rver_patch = le16_to_cpu(rver->patch_version);
> 
> +	if (ver_rom & ~0xffffU) {
> +		rver_rom_high = le16_to_cpu(*(__le16 *)(fw->data + 16));
> +		rver_rom = le32_to_cpu(rver_rom_high << 16 | rver_rom_low);
> +	} else {
> +		rver_rom = (__force u32)rver_rom_low;
> +	}
> +

I don’t get this. Is anything wrong with get_unaligned_le32 etc.?

My brain just hurts with your casting and pointer magic. Maybe the whole rver logic needs a clean up first.

Regards

Marcel