[PATCH v5 73/80] drm/vc4: hdmi: Do the VID_CTL configuration at once

From: Maxime Ripard
Date: Thu Sep 03 2020 - 04:06:50 EST


The VID_CTL setup is done in several places in the driver even though it's
not really required. Let's simplify it a bit to do the configuration in one
go.

Reviewed-by: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
Tested-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
Tested-by: Hoegeun Kwon <hoegeun.kwon@xxxxxxxxxxx>
Tested-by: Stefan Wahren <stefan.wahren@xxxxxxxx>
Signed-off-by: Maxime Ripard <maxime@xxxxxxxxxx>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 14 ++++++--------
1 file changed, 6 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 128d33c8c2c3..8bf69cafdd7e 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -428,10 +428,6 @@ static void vc4_hdmi_set_timings(struct vc4_hdmi *vc4_hdmi,

HDMI_WRITE(HDMI_VERTB0, vertb_even);
HDMI_WRITE(HDMI_VERTB1, vertb);
-
- HDMI_WRITE(HDMI_VID_CTL,
- (vsync_pos ? 0 : VC4_HD_VID_CTL_VSYNC_LOW) |
- (hsync_pos ? 0 : VC4_HD_VID_CTL_HSYNC_LOW));
}

static void vc4_hdmi_recenter_fifo(struct vc4_hdmi *vc4_hdmi)
@@ -520,8 +516,6 @@ static void vc4_hdmi_encoder_pre_crtc_configure(struct drm_encoder *encoder)
if (vc4_hdmi->variant->phy_init)
vc4_hdmi->variant->phy_init(vc4_hdmi, mode);

- HDMI_WRITE(HDMI_VID_CTL, 0);
-
HDMI_WRITE(HDMI_SCHEDULER_CONTROL,
HDMI_READ(HDMI_SCHEDULER_CONTROL) |
VC4_HDMI_SCHEDULER_CONTROL_MANUAL_FORMAT |
@@ -555,15 +549,19 @@ static void vc4_hdmi_encoder_pre_crtc_enable(struct drm_encoder *encoder)

static void vc4_hdmi_encoder_post_crtc_enable(struct drm_encoder *encoder)
{
+ struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
+ bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
+ bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
int ret;

HDMI_WRITE(HDMI_VID_CTL,
- HDMI_READ(HDMI_VID_CTL) |
VC4_HD_VID_CTL_ENABLE |
VC4_HD_VID_CTL_UNDERFLOW_ENABLE |
- VC4_HD_VID_CTL_FRAME_COUNTER_RESET);
+ VC4_HD_VID_CTL_FRAME_COUNTER_RESET |
+ (vsync_pos ? 0 : VC4_HD_VID_CTL_VSYNC_LOW) |
+ (hsync_pos ? 0 : VC4_HD_VID_CTL_HSYNC_LOW));

if (vc4_encoder->hdmi_monitor) {
HDMI_WRITE(HDMI_SCHEDULER_CONTROL,
--
git-series 0.9.1