Re: [RFC PATCH 3/3] opp: Power on (virtual) power domains managed by the OPP core

From: Stephan Gerhold
Date: Tue Aug 25 2020 - 03:34:01 EST


On Tue, Aug 25, 2020 at 08:43:42AM +0200, Ulf Hansson wrote:
> On Tue, 25 Aug 2020 at 06:43, Viresh Kumar <viresh.kumar@xxxxxxxxxx> wrote:
> >
> > On 24-08-20, 17:08, Stephan Gerhold wrote:
> > > On Mon, Aug 24, 2020 at 04:36:57PM +0200, Ulf Hansson wrote:
> > > > That said, perhaps should rely on the consumer to deploy runtime PM
> > > > support, but let the OPP core to set up the device links for the genpd
> > > > virtual devices!?
> > > >
> > >
> > > Yes, that would be the alternative option.
> >
> > That is the right option IMO.
> >
> > > I would be fine with it as long as it also works for the CPUfreq case.
> > >
> > > I don't think anything manages runtime PM for the CPU device, just
> > > like no-one calls dev_pm_opp_set_rate(cpu_dev, 0). So with my patch the
> > > power domain is essentially kept always-on (except for system suspend).
> > > At least in my case this is intended.
> > >
> > > If device links also keep the power domains on if the consumer device
> > > does not make use of runtime PM it should work fine for my case.
> >
> > With device link, you only need to do rpm enable/disable on the consumer device
> > and it will get propagated by itself.
>
> Note that the default state for the genpd virtual device(s) is that
> runtime PM has been enabled for them. This means it's left in runtime
> suspended state, which allows its PM domain to be powered off (if all
> other devices and child domains for it allow that too, of course).
>
> >
> > > Personally, I think my original patch (without device links) fits better
> > > into the OPP API, for the following two reasons.
> > >
> > > With device links:
> > >
> > > 1. Unlike regulators/interconnects, attached power domains would be
> > > controlled by runtime PM instead of dev_pm_opp_set_rate(opp_dev, 0).
> > >
> > > 2. ... some driver using OPP tables might not make use of runtime PM.
> > > In that case, the power domains would stay on the whole time,
> > > even if dev_pm_opp_set_rate(opp_dev, 0) was called.
> > >
> > > With my patch, the power domain state is directly related to the
> > > dev_pm_opp_set_rate(opp_dev, 0) call, which is more intuitive than
> > > relying on the runtime PM state in my opinion.
> >
> > So opp-set-rate isn't in the best of shape TBH, some things are left for the
> > drivers while other are done by it. Regulator-enable/disable was moved to it
> > some time back as people needed something like that. While on the other hand,
> > clk_enable/disable doesn't happen there, nor does rpm enable/disable.
> >
> > Maybe one day we may want to do that, but lets make sure someone wants to do
> > that first.
> >
> > Anyway, even in that case both of the changes would be required. We must make
> > device links nevertheless first. And later on if required, we may want to do rpm
> > enable/disable on the consumer device itself.
>
> This sounds like a reasonable step-by-step approach.
>
> Then, to create the device links, we should use DL_FLAG_PM_RUNTIME,
> DL_FLAG_STATELESS.
>

OK, I will give this a try later this week.

> But whether we should use DL_FLAG_RPM_ACTIVE as well, to initially
> runtime resume the supplier (the genpd virtual device), is harder to
> know - as that kind of depends on expectations by the consumer device
> driver.
>

I'm not sure I understand the purpose of that flag. I thought we want to
link the PM state of the virtual genpd device (supplier) to the PM state
of the device of the OPP table (consumer).

Shouldn't it just determine the initial state based on the state of the
consumer device?

Thanks!
Stephan