Re: [RFT 12/16] memory: brcmstb_dpfe: Add separate entry for compile test

From: Krzysztof Kozlowski
Date: Mon Aug 17 2020 - 14:39:09 EST


On Fri, Jul 24, 2020 at 11:40:09AM -0700, Florian Fainelli wrote:
> On 7/24/20 11:23 AM, Krzysztof Kozlowski wrote:
> > Add separate entry for Broadcom STB DPFE driver, selected by platforms
> > by default. This allows further customization and compile testing.
> >
> > Signed-off-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> > ---
> >
> > I have other changes around drivers/memory/Kconfig pending. Sending them
> > together would avoid conflicts.
> >
> > ---
> > arch/arm/mach-bcm/Kconfig | 1 +
> > arch/arm64/Kconfig.platforms | 1 +
> > drivers/memory/Kconfig | 11 +++++++++++
> > drivers/memory/Makefile | 2 +-
> > 4 files changed, 14 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
> > index 1df0ee01ee02..b0c45238e69b 100644
> > --- a/arch/arm/mach-bcm/Kconfig
> > +++ b/arch/arm/mach-bcm/Kconfig
> > @@ -208,6 +208,7 @@ config ARCH_BRCMSTB
> > select ARM_GIC
> > select ARM_ERRATA_798181 if SMP
> > select HAVE_ARM_ARCH_TIMER
> > + select BRCMSTB_DPFE
> > select BRCMSTB_L2_IRQ
> > select BCM7120_L2_IRQ
> > select ARCH_HAS_HOLES_MEMORYMODEL
> > diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
> > index ddc3bf75257f..f7791ed0ed6d 100644
> > --- a/arch/arm64/Kconfig.platforms
> > +++ b/arch/arm64/Kconfig.platforms
> > @@ -68,6 +68,7 @@ config ARCH_BRCMSTB
> > bool "Broadcom Set-Top-Box SoCs"
> > select ARCH_HAS_RESET_CONTROLLER
> > select BCM7038_L1_IRQ
> > + select BRCMSTB_DPFE
>
> The select is probably not warranted, see below.
>
> > select BRCMSTB_L2_IRQ
> > select GENERIC_IRQ_CHIP
> > select PINCTRL
> > diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
> > index cd4fc93b50df..fef6f0873fda 100644
> > --- a/drivers/memory/Kconfig
> > +++ b/drivers/memory/Kconfig
> > @@ -54,6 +54,17 @@ config ATMEL_EBI
> > tree is used. This bus supports NANDs, external ethernet controller,
> > SRAMs, ATA devices, etc.
> >
> > +config BRCMSTB_DPFE
> > + bool "Broadcom STB DPFE driver" if COMPILE_TEST
> > + depends on ARCH_BRCMSTB || COMPILE_TEST
>
> Can you make it default ARCH_BRCMSTB and remove the select above?
>
> With that:
>
> Acked-by: Florian Fainelli <f.fainelli@xxxxxxxxx>

Applied with mentioned change.

Best regards,
Krzysztof