Re: [PATCH v5 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board

[Alexandre Torgue]

...

> > +
> > +&sdmmc2_d47_pins_a {
> > +	pins {
> > +		pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
> > +			 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
> > +			 <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
> > +			 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
> > +	};
> > +};
> > +
> > +&sdmmc2_d47_sleep_pins_a {
> > +	pins {
> > +		pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
> > +			 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
> > +			 <STM32_PINMUX('E', 5, ANALOG)>, /* SDMMC2_D6 */
> > +			 <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
> > +	};
> > +};
>
> When I sent out the device trees for the lxa-mc1, Alex wanted
> all pinctrl nodes to be collected in stm32mp15-pinctrl.dtsi.
>
> @Alex, should this be done here as well?

Hi,

Sorry for the late answer. Yes it has to be defined in 
stm32mp15-pinctrl.dtsi. If at the end there are too much definitions for 
the same pins or group of pins, I'll find a smarter way for pin 
definition, but currently all pin definitions have to be done in 
stm32mp15-pinctrl.dtsi.

cheers
Alex

> > +
> > +&sdmmc2 {
> > +	pinctrl-names = "default", "opendrain", "sleep";
> > +	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> > +	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
> > +	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
> > +	non-removable;
> > +	no-sd;
> > +	no-sdio;
> > +	st,neg-edge;
> > +	bus-width = <8>;
> > +	vmmc-supply = <&v3v3>;
> > +	vqmmc-supply = <&v3v3>;
> > +	mmc-ddr-3_3v;
> > +	status = "okay";
> > +};
> > +
> > diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> > new file mode 100644
> > index 000000000000..619243807842
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> > @@ -0,0 +1,73 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> > +/*
> > + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@xxxxxxxxx>.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "stm32mp157c-odyssey-som.dtsi"
> > +
> > +/ {
> > +	model = "Seeed Studio Odyssey-STM32MP157C Board";
> > +	compatible = "seeed,stm32mp157c-odyssey",
> > +		     "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
> > +
> > +	aliases {
> > +		ethernet0 = &ethernet0;
> > +		serial0 = &uart4;
> > +	};
> > +
> > +	chosen {
> > +		stdout-path = "serial0:115200n8";
> > +	};
> > +};
> > +
> > +&ethernet0 {
> > +	status = "okay";
> > +	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
> > +	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
> > +	pinctrl-names = "default", "sleep";
> > +	phy-mode = "rgmii-id";
> > +	max-speed = <1000>;
> > +	phy-handle = <&phy0>;
> > +
> > +	mdio0 {
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		compatible = "snps,dwmac-mdio";
> > +		phy0: ethernet-phy@7 { /* KSZ9031RN */
> > +			reg = <7>;
>
> reset-gpios is missing. I see that the vendor u-boot does it
> in board code, but you don't want Linux to depend on this.
>
> > +		};
> > +	};
> > +};
> > +
> > +&i2c1 {
> > +	pinctrl-names = "default", "sleep";
> > +	pinctrl-0 = <&i2c1_pins_a>;
> > +	pinctrl-1 = <&i2c1_sleep_pins_a>;
> > +	i2c-scl-rising-time-ns = <100>;
> > +	i2c-scl-falling-time-ns = <7>;
> > +	status = "okay";
> > +	/delete-property/dmas;
> > +	/delete-property/dma-names;
> > +};
> > +
> > +&sdmmc1 {
> > +	pinctrl-names = "default", "opendrain", "sleep";
> > +	pinctrl-0 = <&sdmmc1_b4_pins_a>;
> > +	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> > +	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> > +	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > +	disable-wp;
> > +	st,neg-edge;
> > +	bus-width = <4>;
> > +	vmmc-supply = <&v3v3>;
> > +	status = "okay";
> > +};
> > +
> > +&uart4 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart4_pins_a>;
> > +	status = "okay";
> > +};
> > +