Re: [PATCH 3/4] clk: mediatek: Add configurable enable control to mtk_pll_data

[Nicolas Boichat]

On Wed, Jul 22, 2020 at 2:50 PM Weiyi Lu <weiyi.lu@xxxxxxxxxxxx> wrote:
>
> In all MediaTek PLL design, bit 0 of CON0 register is always
> the enable bit.
> However, there's a special case of usbpll on MT8192.
> The enable bit of usbpll is moved to bit 2 of other register.
> Add configurable en_reg and base_en_bit for enable control or
> using the default if without setting in pll data.
>
> Signed-off-by: Weiyi Lu <weiyi.lu@xxxxxxxxxxxx>
> ---
>  drivers/clk/mediatek/clk-mtk.h |  2 ++
>  drivers/clk/mediatek/clk-pll.c | 26 ++++++++++++++++++++++----
>  2 files changed, 24 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/clk/mediatek/clk-mtk.h b/drivers/clk/mediatek/clk-mtk.h
> index c3d6756..8bb0b3d 100644
> --- a/drivers/clk/mediatek/clk-mtk.h
> +++ b/drivers/clk/mediatek/clk-mtk.h
> @@ -233,6 +233,8 @@ struct mtk_pll_data {
>         uint32_t pcw_chg_reg;
>         const struct mtk_pll_div_table *div_table;
>         const char *parent_name;
> +       uint32_t en_reg;
> +       uint8_t base_en_bit;
>  };
>
>  void mtk_clk_register_plls(struct device_node *node,
> diff --git a/drivers/clk/mediatek/clk-pll.c b/drivers/clk/mediatek/clk-pll.c
> index f440f2cd..b8ccd42 100644
> --- a/drivers/clk/mediatek/clk-pll.c
> +++ b/drivers/clk/mediatek/clk-pll.c
> @@ -44,6 +44,7 @@ struct mtk_clk_pll {
>         void __iomem    *tuner_en_addr;
>         void __iomem    *pcw_addr;
>         void __iomem    *pcw_chg_addr;
> +       void __iomem    *en_addr;
>         const struct mtk_pll_data *data;
>  };
>
> @@ -56,7 +57,10 @@ static int mtk_pll_is_prepared(struct clk_hw *hw)
>  {
>         struct mtk_clk_pll *pll = to_mtk_clk_pll(hw);
>
> -       return (readl(pll->base_addr + REG_CON0) & CON0_BASE_EN) != 0;
> +       if (pll->en_addr)
> +               return (readl(pll->en_addr) & BIT(pll->data->base_en_bit)) != 0;
> +       else
> +               return (readl(pll->base_addr + REG_CON0) & CON0_BASE_EN) != 0;
>  }
>
>  static unsigned long __mtk_pll_recalc_rate(struct mtk_clk_pll *pll, u32 fin,
> @@ -251,6 +255,12 @@ static int mtk_pll_prepare(struct clk_hw *hw)
>         r |= pll->data->en_mask;
>         writel(r, pll->base_addr + REG_CON0);
>

This is not a new change, but I'm wondering if the asymmetry is
intentional here, that is, prepare sets bit pll->data->en_mask of
REG_CON0; unprepare clears CON0_BASE_EN of REG_CON0.

With this patch, if pll->en_addr is set, you set both
pll->data->en_mask _and_ pll->data->base_en_bit, and clear only
pll->data->base_en_bit.

> +       if (pll->en_addr) {
> +               r = readl(pll->en_addr);
> +               r |= BIT(pll->data->base_en_bit);
> +               writel(r, pll->en_addr);
> +       }
> +
>         __mtk_pll_tuner_enable(pll);
>
>         udelay(20);
> @@ -277,9 +287,15 @@ static void mtk_pll_unprepare(struct clk_hw *hw)
>
>         __mtk_pll_tuner_disable(pll);
>
> -       r = readl(pll->base_addr + REG_CON0);
> -       r &= ~CON0_BASE_EN;
> -       writel(r, pll->base_addr + REG_CON0);
> +       if (pll->en_addr) {
> +               r = readl(pll->en_addr);
> +               r &= ~BIT(pll->data->base_en_bit);
> +               writel(r, pll->en_addr);
> +       } else {
> +               r = readl(pll->base_addr + REG_CON0);
> +               r &= ~CON0_BASE_EN;
> +               writel(r, pll->base_addr + REG_CON0);
> +       }
>
>         r = readl(pll->pwr_addr) | CON0_ISO_EN;
>         writel(r, pll->pwr_addr);
> @@ -321,6 +337,8 @@ static struct clk *mtk_clk_register_pll(const struct mtk_pll_data *data,
>                 pll->tuner_addr = base + data->tuner_reg;
>         if (data->tuner_en_reg)
>                 pll->tuner_en_addr = base + data->tuner_en_reg;
> +       if (data->en_reg)
> +               pll->en_addr = base + data->en_reg;

If the answer to my question above holds (asymmetry is not
intentional), this patch/the code could be simplified a lot if you
also added a pll->en_bit member, and, here, did this:

if (pll->en_reg) {
   pll->en_addr = base + data->en_reg;
   pll->end_bit = data->en_bit;
} else {
   pll->en_addr = pll->base_addr + REG_CON0;
   pll->en_bit = CON0_BASE_EN;
}

>         pll->hw.init = &init;
>         pll->data = data;
>
> --
> 1.8.1.1.dirty