[PATCH v8 1/2] arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone

From: Ondrej Jirman
Date: Thu Jul 02 2020 - 04:14:52 EST


From: Icenowy Zheng <icenowy@xxxxxxx>

PinePhone uses PWM backlight and a XBD599 LCD panel over DSI for
display.

Backlight levels curve was optimized by Martijn Braam using a
lux meter.

Add its device nodes.

Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
Signed-off-by: Martijn Braam <martijn@xxxxxxxxx>
Signed-off-by: Ondrej Jirman <megous@xxxxxxxxxx>
Acked-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
.../allwinner/sun50i-a64-pinephone-1.1.dts | 19 +++++++++++
.../dts/allwinner/sun50i-a64-pinephone.dtsi | 33 +++++++++++++++++++
2 files changed, 52 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
index 06a775c41664..3e99a87e9ce5 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
@@ -9,3 +9,22 @@ / {
model = "Pine64 PinePhone Braveheart (1.1)";
compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64";
};
+
+&backlight {
+ power-supply = <&reg_ldo_io0>;
+ /*
+ * PWM backlight circuit on this PinePhone revision was changed since
+ * 1.0, and the lowest PWM duty cycle that doesn't lead to backlight
+ * being off is around 20%. Duty cycle for the lowest brightness level
+ * also varries quite a bit between individual boards, so the lowest
+ * value here was chosen as a safe default.
+ */
+ brightness-levels = <
+ 774 793 814 842
+ 882 935 1003 1088
+ 1192 1316 1462 1633
+ 1830 2054 2309 2596
+ 2916 3271 3664 4096>;
+ num-interpolated-steps = <50>;
+ default-brightness-level = <400>;
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
index cefda145c3c9..a89425ad3727 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
@@ -16,6 +16,13 @@ aliases {
serial0 = &uart0;
};

+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>;
+ enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+ /* Backlight configuration differs per PinePhone revision. */
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
@@ -84,6 +91,28 @@ &dai {
status = "okay";
};

+&de {
+ status = "okay";
+};
+
+&dphy {
+ status = "okay";
+};
+
+&dsi {
+ vcc-dsi-supply = <&reg_dldo1>;
+ status = "okay";
+
+ panel@0 {
+ compatible = "xingbangda,xbd599";
+ reg = <0>;
+ reset-gpios = <&pio 3 23 GPIO_ACTIVE_LOW>; /* PD23 */
+ iovcc-supply = <&reg_dldo2>;
+ vcc-supply = <&reg_ldo_io0>;
+ backlight = <&backlight>;
+ };
+};
+
&ehci0 {
status = "okay";
};
@@ -188,6 +217,10 @@ &r_pio {
*/
};

+&r_pwm {
+ status = "okay";
+};
+
&r_rsb {
status = "okay";

--
2.27.0