[PATCH v2] ARM: dts: am335x-pocketbeagle: set default mux for gpio pins

From: Drew Fustini
Date: Sun Jun 28 2020 - 11:25:12 EST


These pins on the PocketBeagle P1 and P2 headers are connected to AM3358
balls with gpio lines, and these pins are not used for any other
peripherals by default. These GPIO lines are unclaimed and could be used
by userspace program through the gpiod ABI.

This patch adds a "default" state in the am33xx_pinmux node and sets the
mux for those pins to gpio (mode 7) with input enable and pull-up or
down (per the ball reset rel. state in section 4.2 of datasheet [0]).

[0] http://www.ti.com/lit/ds/symlink/am3358.pdf

Signed-off-by: Drew Fustini <drew@xxxxxxxxxxxxxxx>
---
v2 changes:
- change default mux from output to input. Input is safer as it does
not drive the line. If the user wants output, they will need to edit
this device tree.

arch/arm/boot/dts/am335x-pocketbeagle.dts | 98 +++++++++++++++++++++++
1 file changed, 98 insertions(+)

diff --git a/arch/arm/boot/dts/am335x-pocketbeagle.dts b/arch/arm/boot/dts/am335x-pocketbeagle.dts
index f0b222201b86..e9cc5cb218f1 100644
--- a/arch/arm/boot/dts/am335x-pocketbeagle.dts
+++ b/arch/arm/boot/dts/am335x-pocketbeagle.dts
@@ -60,6 +60,104 @@ vmmcsd_fixed: fixedregulator0 {
};

&am33xx_pinmux {
+
+ pinctrl-names = "default";
+ pinctrl-0 = < &P2_03_gpio &P1_34_gpio &P2_19_gpio &P2_24_gpio
+ &P2_33_gpio &P2_22_gpio &P2_18_gpio &P2_10_gpio
+ &P2_06_gpio &P2_04_gpio &P2_02_gpio &P2_08_gpio
+ &P2_17_gpio >;
+
+ /* P2_03 (ZCZ ball T10) gpio0_23 0x824 */
+ P2_03_gpio: pinmux_P2_03_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P1_34 (ZCZ ball T11) gpio0_26 0x828 */
+ P1_34_gpio: pinmux_P1_34_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD10, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P2_19 (ZCZ ball U12) gpio0_27 0x82c */
+ P2_19_gpio: pinmux_P2_19_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P2_24 (ZCZ ball T12) gpio1_12 0x830 */
+ P2_24_gpio: pinmux_P2_24_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P2_33 (ZCZ ball R12) gpio1_13 0x834 */
+ P2_33_gpio: pinmux_P2_33_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P2_22 (ZCZ ball V13) gpio1_14 0x838 */
+ P2_22_gpio: pinmux_P2_22_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P2_18 (ZCZ ball U13) gpio1_15 0x83c */
+ P2_18_gpio: pinmux_P2_18_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P2_10 (ZCZ ball R14) gpio1_20 0x850 */
+ P2_10_gpio: pinmux_P2_10_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P2_06 (ZCZ ball U16) gpio1_25 0x864 */
+ P2_06_gpio: pinmux_P2_06_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P2_04 (ZCZ ball T16) gpio1_26 0x868 */
+ P2_04_gpio: pinmux_P2_04_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P2_02 (ZCZ ball V17) gpio1_27 0x86c */
+ P2_02_gpio: pinmux_P2_02_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
+ /* P2_08 (ZCZ ball U18) gpio1_28 0x878 */
+ P2_08_gpio: pinmux_P2_08_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_BEN1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+ >;
+ };
+
+ /* P2_17 (ZCZ ball V12) gpio2_1 0x88c */
+ P2_17_gpio: pinmux_P2_17_gpio {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_CLK, PIN_INPUT_PULLUP, MUX_MODE7)
+ >;
+ };
+
i2c2_pins: pinmux-i2c2-pins {
pinctrl-single,pins = <
AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLUP, MUX_MODE3) /* (D17) uart1_rtsn.I2C2_SCL */
--
2.25.1