Re: [PATCH v2 2/2] cpufreq: Specify default governor on command line

From: Rafael J. Wysocki
Date: Thu Jun 25 2020 - 10:08:32 EST


On Thu, Jun 25, 2020 at 3:50 PM Quentin Perret <qperret@xxxxxxxxxx> wrote:
>
> On Thursday 25 Jun 2020 at 15:28:43 (+0200), Rafael J. Wysocki wrote:
> > On Thu, Jun 25, 2020 at 1:53 PM Quentin Perret <qperret@xxxxxxxxxx> wrote:
> > >
> > > On Thursday 25 Jun 2020 at 13:44:34 (+0200), Rafael J. Wysocki wrote:
> > > > On Thu, Jun 25, 2020 at 1:36 PM Viresh Kumar <viresh.kumar@xxxxxxxxxx> wrote:
> > > > > This change is not right IMO. This part handles the set-policy case,
> > > > > where there are no governors. Right now this code, for some reasons
> > > > > unknown to me, forcefully uses the default governor set to indicate
> > > > > the policy, which is not a great idea in my opinion TBH. This doesn't
> > > > > and shouldn't care about governor modules and should only be looking
> > > > > at strings instead of governor pointer.
> > > >
> > > > Sounds right.
> > > >
> > > > > Rafael, I even think we should remove this code completely and just
> > > > > rely on what the driver has sent to us. Using the selected governor
> > > > > for set policy drivers is very confusing and also we shouldn't be
> > > > > forced to compiling any governor for the set-policy case.
> > > >
> > > > Well, AFAICS the idea was to use the default governor as a kind of
> > > > default policy proxy, but I agree that strings should be sufficient
> > > > for that.
> > >
> > > I agree with all the above. I'd much rather not rely on the default
> > > governor name to populate the default policy, too, so +1 from me.
> >
> > So before this series the default governor was selected at the kernel
> > configuration time (pre-build) and was always built-in. Because it
> > could not go away, its name could be used to indicate the default
> > policy for the "setpolicy" drivers.
> >
> > After this series, however, it cannot be used this way reliably, but
> > you can still pass cpufreq_param_governor to cpufreq_parse_policy()
> > instead of def_gov->name in cpufreq_init_policy(), can't you?
>
> Good point. I also need to fallback to the default builtin governor if
> the command line parameter isn't valid (or non-existent), so perhaps
> something like so?

Yes, that should work if I haven't missed anything.

> iff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c
> index dad6b85f4c89..20a2020abf88 100644
> --- a/drivers/cpufreq/cpufreq.c
> +++ b/drivers/cpufreq/cpufreq.c
> @@ -653,6 +653,23 @@ static unsigned int cpufreq_parse_policy(char *str_governor)
> return CPUFREQ_POLICY_UNKNOWN;
> }
>
> +static unsigned int cpufreq_default_policy(void)
> +{
> + unsigned int pol;
> +
> + pol = cpufreq_parse_policy(cpufreq_param_governor);
> + if (pol != CPUFREQ_POLICY_UNKNOWN)
> + return pol;
> +
> + if (IS_BUILTIN(CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE))
> + return CPUFREQ_POLICY_PERFORMANCE;
> +
> + if (IS_BUILTIN(CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE))
> + return CPUFREQ_POLICY_POWERSAVE;
> +
> + return CPUFREQ_POLICY_UNKNOWN;
> +}
> +
> /**
> * cpufreq_parse_governor - parse a governor string only for has_target()
> * @str_governor: Governor name.
> @@ -1085,8 +1102,8 @@ static int cpufreq_init_policy(struct cpufreq_policy *policy)
> /* Use the default policy if there is no last_policy. */
> if (policy->last_policy) {
> pol = policy->last_policy;
> - } else if (default_governor) {
> - pol = cpufreq_parse_policy(default_governor->name);
> + } else {
> + pol = cpufreq_default_policy();
> /*
> * In case the default governor is neiter "performance"
> * nor "powersave", fall back to the initial policy