Re: [RFC PATCH 0/1] Add LTR controls

From: dikshita
Date: Tue Jun 16 2020 - 14:41:43 EST


Hi Hans, Nicolas,

Thanks for your comments.

On 2020-06-12 14:41, Hans Verkuil wrote:
Hi Dikshita, Nicolas,

On 11/06/2020 16:22, Nicolas Dufresne wrote:
Le jeudi 11 juin 2020 Ã 15:55 +0530, Dikshita Agarwal a Ãcrit :
LTR (Long Term Reference) frames are the frames that are encoded sometime in the past
and stored in the DPB buffer list to be used as reference to encode future frames.
One usage of LTR encoding is to reduce error propagation for video transmission
in packet lossy networks. For example, encoder may want to specify some key frames as
LTR pictures and use them as reference frames for encoding. With extra protection
selectively on these LTR frames or synchronization with the receiver of reception of
the LTR frames during transmission, decoder can receive reference frames more reliably
than other non-reference frames. As a result, transmission error can be effectively
restricted within certain frames rather than propagated to future frames.

We are introducing below V4l2 Controls for this feature
1. V4L2_CID_MPEG_VIDEO_LTRCOUNT
a. This is used to query or configure the number of LTR frames.
This is a static control and is controlled by the client.
b. The LTR index varies from 0 to the max LTR-1.
c. If LTR Count is more than max supported LTR count (max LTR) by driver, it will be rejected.
d. Auto Marking : If LTR count is non zero,
1) first LTR count frames would be mark as LTR automatically after
every IDR frame (inclusive).
2) For multilayer encoding: first LTR count base layer reference frames starting after
every IDR frame (inclusive) in encoding order would be marked as LTR frames by the encoder.
3) Auto marking of LTR due to IDR should consider following conditions:
1. The frame is not already set to be marked as LTR.
2. The frame is part of the base layer in the hierarchical layer case.
3. The number of frames currently marked as LTR is less than the maximum LTR frame index plus 1.
e. Encoder needs to handle explicit Mark/Use command when encoder is still doing "auto" marking

I don't follow this, quite possibly due to lack of experience with encoders.

I kind of would expect to see two modes: either automatic where encoders can
mark up to LTR_COUNT frames as long term reference, and userspace just sets
LTR_COUNT and doesn't have to do anything else.

Or it is manual mode where userspace explicitly marks long term reference
frames.

From the proposal above it looks like you can mix auto and manual modes.

BTW, how do you 'unmark' long term reference frames?

This feature is for stateful encoders, right?


Perhaps we are missing a LONG_TERM_REFERENCE_MODE ? I bet some encoder
can select by themself long term references and even some encoders may
not let the user decide.

(not huge han of LTR acronyme, but that could be fine too, assuming you
add more _).


Userspace sets LTR count which signifies the number of LTR frames encoder needs to generate or keep.
The encoder has to build-up its internal buffer reference list (aka DBP list or recon buffer list).
In order to achieve that encoder will fill It's LTR (long term references) list and STR (short term references) list
by auto marking n frames as LTR frames(n is equal to LTR count) based on auto-marking dictated by the encoder spec.
The client then can replace those automatically marked frames with new frames using V4L2_CID_MPEG_VIDEO_MARKLTRFRAME and can ask
encoder to refer the newly marked frame for encoding the next frame using V4L2_CID_MPEG_VIDEO_USELTRFRAME.


2. V4L2_CID_MPEG_VIDEO_MARKLTRFRAME :
a. This signals to mark the current frame as LTR frame. It is a dynamic control and also provide the LTR index to be used.
b. the LTR index provided by this control should never exceed the max LTR-1. Else it will be rejected.

The "current" frame seems a bit loose. Perhaps you wanted to use buffer
flags ? A bit like what we have to signal TOP/BOTTOM fields in
alternate interlacing.

I was thinking the same thing. Using a control for this doesn't seem right.


the client sets this to replace automatically marked frames by the encoder with a particular frame.
this provides an index that ranges from 0 to LTR count-1 and then the particular frame will be marked with that index.
this can be achieved through request by associating this control with a specific buffer to make it synchronized.



3. V4L2_CID_MPEG_VIDEO_USELTRFRAME :
a. This specifies the LTR frame(s) to be used for encoding the current frame. This is a dynamic control.
b. LTR Use Bitmap : this consists of bits [0, 15]. A total of N LSB bits of this field are valid,
where N is the maximum number of LTRs supported. All the other bits are invalid and should be rejected.
The LSB corresponds to the LTR index 0. Bit N-1 from the LSB corresponds to the LTR index max LTR-1.

How would userspace know this? Esp. with auto marking since userspace would have
to predict how auto marking works (if I understand this correctly).


Client sets LTR count which tells about the number of LTR frames automatically marked by the encoder.
so client can use LTR index (0 to LTR count -1) to ask encoder to refer any particular
frame (marked automatically by driver or marked by client with V4L2_CID_MPEG_VIDEO_MARKLTRFRAME) as a reference to encode the next frame.

For which HW encoder is this meant?

This is primarily meant for H264 and HEVC.

Thanks,
Dikshita


Note, I haven't captured very well the userspace control flow, perhaps
this could be enhanced through writing some documentation.

As per all other generic encoder controls, we need to make sure it will
be usable and flexible enough for multiple HW blocks, as it can be
tedious to extend later otherwise. It is important that along with this
RFC you provide some comparisons with with other HW / SW APIs in order
to help justify the design decisions. I also think there should be
link made V4L2_CID_MPEG_VIDEO_GOP_* , number of B-Frames etc.

I agree with Nicolas.

Regards,

Hans


regards,
Nicolas


Dikshita Agarwal (1):
media: v4l2-ctrls: add control for ltr

drivers/media/v4l2-core/v4l2-ctrls.c | 6 ++++++
include/uapi/linux/v4l2-controls.h | 4 ++++
2 files changed, 10 insertions(+)