Re: [PATCH] irqchip/gic-v3-its: Don't try to move a disabled irq

From: Marc Zyngier
Date: Sat May 30 2020 - 12:49:40 EST


Hi Ali,

On Fri, 29 May 2020 12:36:42 +0000
"Saidi, Ali" <alisaidi@xxxxxxxxxx> wrote:

> Hi Marc,
>
> > On May 29, 2020, at 3:33 AM, Marc Zyngier <maz@xxxxxxxxxx> wrote:
> >
> > Hi Ali,
> >
> >> On 2020-05-29 02:55, Ali Saidi wrote:
> >> If an interrupt is disabled the ITS driver has sent a discard removing
> >> the DeviceID and EventID from the ITT. After this occurs it can't be
> >> moved to another collection with a MOVI and a command error occurs if
> >> attempted. Before issuing the MOVI command make sure that the IRQ isn't
> >> disabled and change the activate code to try and use the previous
> >> affinity.
> >>
> >> Signed-off-by: Ali Saidi <alisaidi@xxxxxxxxxx>
> >> ---
> >> drivers/irqchip/irq-gic-v3-its.c | 18 +++++++++++++++---
> >> 1 file changed, 15 insertions(+), 3 deletions(-)
> >>
> >> diff --git a/drivers/irqchip/irq-gic-v3-its.c
> >> b/drivers/irqchip/irq-gic-v3-its.c
> >> index 124251b0ccba..1235dd9a2fb2 100644
> >> --- a/drivers/irqchip/irq-gic-v3-its.c
> >> +++ b/drivers/irqchip/irq-gic-v3-its.c
> >> @@ -1540,7 +1540,11 @@ static int its_set_affinity(struct irq_data *d,
> >> const struct cpumask *mask_val,
> >> /* don't set the affinity when the target cpu is same as current one
> >> */
> >> if (cpu != its_dev->event_map.col_map[id]) {
> >> target_col = &its_dev->its->collections[cpu];
> >> - its_send_movi(its_dev, target_col, id);
> >> +
> >> + /* If the IRQ is disabled a discard was sent so don't move */
> >> + if (!irqd_irq_disabled(d))
> >> + its_send_movi(its_dev, target_col, id);
> >> +
> >
> > This looks wrong. What you are testing here is whether the interrupt
> > is masked, not that there isn't a valid translation.
> Iâm not exactly sure the correct condition, but what Iâm looking for
> is interrupts which are deactivated and we have thus sent a discard.

That looks like IRQD_IRQ_STARTED not being set in this case.

> >
> > In the commit message, you're saying that we've issued a discard.
> > This hints at doing a set_affinity on an interrupt that has been
> > deactivated (mapping removed). Is that actually the case? If so,
> > why was it deactivated
> > the first place?
> This is the case. If we down a NIC, that interfaceâs MSIs will be
> deactivated but remain allocated until the device is unbound from the
> driver or the NIC is brought up.
>
> While stressing down/up a device Iâve found that irqbalance can move
> interrupts and you end up with the situation described. The device is
> downed, the interrupts are deactivated but still present and then
> trying to move one results in sending a MOVI after the DISCARD which
> is an error per the GIC spec.

Not great indeed. But this is not, as far as I can tell, a GIC
driver problem.

The semantic of activate/deactivate (which maps to started/shutdown
in the IRQ code) is that the HW resources for a given interrupt are
only committed when the interrupt is activated. Trying to perform
actions involving the HW on an interrupt that isn't active cannot be
guaranteed to take effect.

I'd rather address it in the core code, by preventing set_affinity (and
potentially others) to take place when the interrupt is not in the
STARTED state. Userspace would get an error, which is perfectly
legitimate, and which it already has to deal with it for plenty of other
reasons.

>
> >
> >> its_dev->event_map.col_map[id] = cpu;
> >> irq_data_update_effective_affinity(d,
> >> cpumask_of(cpu)); }
> >> @@ -3439,8 +3443,16 @@ static int its_irq_domain_activate(struct
> >> irq_domain *domain,
> >> if (its_dev->its->numa_node >= 0)
> >> cpu_mask = cpumask_of_node(its_dev->its->numa_node);
> >>
> >> - /* Bind the LPI to the first possible CPU */
> >> - cpu = cpumask_first_and(cpu_mask, cpu_online_mask);
> >> + /* If the cpu set to a different CPU that is still online
> >> use it */
> >> + cpu = its_dev->event_map.col_map[event];
> >> +
> >> + cpumask_and(cpu_mask, cpu_mask, cpu_online_mask);
> >> +
> >> + if (!cpumask_test_cpu(cpu, cpu_mask)) {
> >> + /* Bind the LPI to the first possible CPU */
> >> + cpu = cpumask_first(cpu_mask);
> >> + }
> >> +
> >> if (cpu >= nr_cpu_ids) {
> >> if (its_dev->its->flags &
> >> ITS_FLAGS_WORKAROUND_CAVIUM_23144) return -EINVAL;
> >
> > So you deactivate an interrupt, do a set_affinity that doesn't issue
> > a MOVI but preserves the affinity, then reactivate it and hope that
> > the new mapping will target the "right" CPU.
> >
> > That seems a bit mad, but I presume this isn't the whole story...
> Doing some experiments it appears as though other interrupts
> controllers do preserve affinity across deactivate/activate, so this
> is my attempt at doing the same.

I believe this is only an artefact of these other controllers not
requiring any resource to be committed into the HW (SPIs wouldn't care,
for example).

Thanks,

M.
--
Jazz is not dead. It just smells funny...