Re: [PATCH v3 104/105] dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings

From: Rob Herring
Date: Fri May 29 2020 - 14:18:39 EST


On Wed, May 27, 2020 at 05:49:14PM +0200, Maxime Ripard wrote:
> The HDMI controllers found in the BCM2711 SoC need some adjustments to the
> bindings, especially since the registers have been shuffled around in more
> register ranges.
>
> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> Cc: devicetree@xxxxxxxxxxxxxxx
> Signed-off-by: Maxime Ripard <maxime@xxxxxxxxxx>
> ---
> Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 109 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
>
> diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> new file mode 100644
> index 000000000000..6091fe3d315b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> @@ -0,0 +1,109 @@
> +# SPDX-License-Identifier: GPL-2.0

Dual license...

> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/brcm,bcm2711-hdmi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Broadcom BCM2711 HDMI Controller Device Tree Bindings
> +
> +maintainers:
> + - Eric Anholt <eric@xxxxxxxxxx>
> +
> +properties:
> + compatible:
> + enum:
> + - brcm,bcm2711-hdmi0
> + - brcm,bcm2711-hdmi1

What's the difference between the 2 blocks?

> +
> + reg:
> + items:
> + - description: HDMI controller register range
> + - description: DVP register range
> + - description: HDMI PHY register range
> + - description: Rate Manager register range
> + - description: Packet RAM register range
> + - description: Metadata RAM register range
> + - description: CSC register range
> + - description: CEC register range
> + - description: HD register range
> +
> + reg-names:
> + items:
> + - const: hdmi
> + - const: dvp
> + - const: phy
> + - const: rm
> + - const: packet
> + - const: metadata
> + - const: csc
> + - const: cec
> + - const: hd
> +
> + clocks:
> + description: The HDMI state machine clock
> +
> + clock-names:
> + const: hdmi
> +
> + ddc:
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/phandle
> + description: >
> + Phandle of the I2C controller used for DDC EDID probing

Goes in the connector.

And isn't the standard name ddc-i2c-bus?

> +
> + hpd-gpios:
> + description: >
> + The GPIO pin for the HDMI hotplug detect (if it doesn't appear
> + as an interrupt/status bit in the HDMI controller itself)

Goes in the connector.

> +
> + dmas:
> + maxItems: 1
> + description: >
> + Should contain one entry pointing to the DMA channel used to
> + transfer audio data.
> +
> + dma-names:
> + const: audio-rx
> +
> + resets:
> + maxItems: 1
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - clocks
> + - resets
> + - ddc
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + hdmi0: hdmi@7ef00700 {
> + compatible = "brcm,bcm2711-hdmi0";
> + reg = <0x7ef00700 0x300>,
> + <0x7ef00300 0x200>,
> + <0x7ef00f00 0x80>,
> + <0x7ef00f80 0x80>,
> + <0x7ef01b00 0x200>,
> + <0x7ef01f00 0x400>,
> + <0x7ef00200 0x80>,
> + <0x7ef04300 0x100>,
> + <0x7ef20000 0x100>;
> + reg-names = "hdmi",
> + "dvp",
> + "phy",
> + "rm",
> + "packet",
> + "metadata",
> + "csc",
> + "cec",
> + "hd";
> + clocks = <&firmware_clocks 13>;
> + clock-names = "hdmi";
> + resets = <&dvp 0>;
> + ddc = <&ddc0>;
> + };
> +
> +...
> --
> git-series 0.9.1