RE: [PATCH 5/5] crypto: stm32/crc: protect from concurrent accesses

From: Nicolas TOROMANOFF
Date: Mon May 25 2020 - 05:01:41 EST


> -----Original Message-----
> From: Ard Biesheuvel <ardb@xxxxxxxxxx>
> Sent: Monday, May 25, 2020 9:46 AM
> To: Nicolas TOROMANOFF <nicolas.toromanoff@xxxxxx>
> Subject: Re: [PATCH 5/5] crypto: stm32/crc: protect from concurrent accesses
>
> On Mon, 25 May 2020 at 09:24, Nicolas TOROMANOFF
> <nicolas.toromanoff@xxxxxx> wrote:
> >
> > Hello,
> >
> > > -----Original Message-----
> > > From: Ard Biesheuvel <ardb@xxxxxxxxxx>
> > > Sent: Friday, May 22, 2020 6:12 PM>
> > > On Tue, 12 May 2020 at 16:13, Nicolas Toromanoff
> > > <nicolas.toromanoff@xxxxxx> wrote:
> > > >
> > > > Protect STM32 CRC device from concurrent accesses.
> > > >
> > > > As we create a spinlocked section that increase with buffer size,
> > > > we provide a module parameter to release the pressure by splitting
> > > > critical section in chunks.
> > > >
> > > > Size of each chunk is defined in burst_size module parameter.
> > > > By default burst_size=0, i.e. don't split incoming buffer.
> > > >
> > > > Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@xxxxxx>
> > >
> > > Would you mind explaining the usage model here? It looks like you
> > > are sharing a CRC hardware accelerator with a synchronous interface
> > > between different users by using spinlocks? You are aware that this
> > > will tie up the waiting CPUs completely during this time, right? So
> > > it would be much better to use a mutex here. Or perhaps it would
> > > make more sense to fall back to a s/w based CRC routine if the h/w is tied up
> working for another task?
> >
> > I know mutex are more acceptable here, but shash _update() and _init()
> > may be call from any context, and so I cannot take a mutex.
> > And to protect my concurrent HW access I only though about spinlock.
> > Due to possible constraint on CPUs, I add a burst_size option to force
> > slitting long buffer into smaller one, and so decrease time we take the lock.
> > But I didn't though to fallback to software CRC.
> >
> > I'll do a patch on top.
> > In in the burst_update() function I'll use a spin_trylock_irqsave() and use
> software CRC32 if HW is already in use.
> >
>
> Right. I didn't even notice that you were keeping interrupts disabled the whole
> time when using the h/w block. That means that any serious use of this h/w
> block will make IRQ latency go through the roof.
>
> I recommend that you go back to the drawing board on this driver, rather than
> papering over the issues with a spin_trylock(). Perhaps it would be better to
> model it as a ahash (even though the h/w block itself is synchronous) and use a
> kthread to feed in the data.

I thought when I updated the driver to move to a ahash interface, but the main usage
of crc32 is the ext4 fs, that calls the shash API.
Commit 877b5691f27a ("crypto: shash - remove shash_desc::flags") removed possibility
to sleep in shash callback. (before this commit and with MAY_SLEEP option set, using
a mutex may have been fine).

By now the solution I see is to use the spin_trylock_irqsave(), fallback to software crc *AND* capping burst_size
to ensure the locked section stay reasonable.

Does this seems acceptable ?

Nicolas.