Re: [PATCH] sdhci: tegra: Avoid reading autocal timeout values when not applicable

From: Thierry Reding
Date: Fri May 22 2020 - 08:52:48 EST


On Fri, May 22, 2020 at 03:42:18PM +0300, Dmitry Osipenko wrote:
> 22.05.2020 15:26, Thierry Reding ÐÐÑÐÑ:
> > On Wed, May 20, 2020 at 01:08:57PM -0700, Sowjanya Komatineni wrote:
> >> When auto calibration timeouts, calibration is disabled and fail-safe
> >> drive strength values are programmed based on the signal voltage.
> >>
> >> Different fail-safe drive strength values based on voltage are
> >> applicable only for SoCs supporting 3V3 and 1V8 pad controls.
> >>
> >> So, this patch avoids reading these properties from the device tree
> >> for SoCs not using pad controls and the warning of missing properties
> >> will not show up on these SoC platforms.
> >>
> >> Signed-off-by: Sowjanya Komatineni <skomatineni@xxxxxxxxxx>
> >> ---
> >> drivers/mmc/host/sdhci-tegra.c | 57 ++++++++++++++++++++++++------------------
> >> 1 file changed, 33 insertions(+), 24 deletions(-)
> >>
> >> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> >> index 3e2c510..141b49b 100644
> >> --- a/drivers/mmc/host/sdhci-tegra.c
> >> +++ b/drivers/mmc/host/sdhci-tegra.c
> >> @@ -605,6 +605,39 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
> >> autocal->pull_down_1v8 = 0;
> >>
> >> err = device_property_read_u32(host->mmc->parent,
> >> + "nvidia,pad-autocal-pull-up-offset-sdr104",
> >> + &autocal->pull_up_sdr104);
> >> + if (err)
> >> + autocal->pull_up_sdr104 = autocal->pull_up_1v8;
> >> +
> >> + err = device_property_read_u32(host->mmc->parent,
> >> + "nvidia,pad-autocal-pull-down-offset-sdr104",
> >> + &autocal->pull_down_sdr104);
> >> + if (err)
> >> + autocal->pull_down_sdr104 = autocal->pull_down_1v8;
> >> +
> >> + err = device_property_read_u32(host->mmc->parent,
> >> + "nvidia,pad-autocal-pull-up-offset-hs400",
> >> + &autocal->pull_up_hs400);
> >> + if (err)
> >> + autocal->pull_up_hs400 = autocal->pull_up_1v8;
> >> +
> >> + err = device_property_read_u32(host->mmc->parent,
> >> + "nvidia,pad-autocal-pull-down-offset-hs400",
> >> + &autocal->pull_down_hs400);
> >> + if (err)
> >> + autocal->pull_down_hs400 = autocal->pull_down_1v8;
> >> +
> >> + /*
> >> + * Different fail-safe drive strength values based on the signaling
> >> + * voltage are applicable for SoCs supporting 3V3 and 1V8 pad controls.
> >> + * So, avoid reading below device tree properies for SoCs that don't
> >> + * have NVQUIRK_NEEDS_PAD_CONTROL.
> >> + */
> >> + if (!(tegra_host->soc_data->nvquirks & NVQUIRK_NEEDS_PAD_CONTROL))
> >> + return;
> >
> > Hm... so what exactly is the difference between NVQUIRK_HAS_PADCALIB? I
> > think Tegra30 will also end up calling tegra_sdhci_set_padctrl(), but it
> > will then write the default (0) value for these drive strength. Is that
> > okay?
>
> It won't write 0, but skip the writing if values are 0. Technically T30+
> supports the customized strengths, but I'm not sure whether it was ever
> tested and whether it's really needed. I think Sowjanya said before that
> the default values are always okay for older SoCs.

Alright then, in that case:

Acked-by: Thierry Reding <treding@xxxxxxxxxx>

Attachment: signature.asc
Description: PGP signature