Re: [PATCH v2 1/4] dt-bindings: iio: imu: bmi160: convert txt format to yaml

From: Jonathan Albrieux
Date: Fri May 22 2020 - 04:22:17 EST


On Thu, May 21, 2020 at 07:27:36PM +0100, Jonathan Cameron wrote:
> On Wed, 20 May 2020 09:24:23 +0200
> Jonathan Albrieux <jonathan.albrieux@xxxxxxxxx> wrote:
>
> > On Tue, May 19, 2020 at 06:49:33PM +0100, Jonathan Cameron wrote:
> > > On Tue, 19 May 2020 09:50:57 +0200
> > > Jonathan Albrieux <jonathan.albrieux@xxxxxxxxx> wrote:
> > >
> > > > Converts documentation from txt format to yaml
> > > >
> > > > Signed-off-by: Jonathan Albrieux <jonathan.albrieux@xxxxxxxxx>
> > > > ---
> > > > .../devicetree/bindings/iio/imu/bmi160.txt | 37 --------
> > > > .../devicetree/bindings/iio/imu/bmi160.yaml | 84 +++++++++++++++++++
> > > > 2 files changed, 84 insertions(+), 37 deletions(-)
> > > > delete mode 100644 Documentation/devicetree/bindings/iio/imu/bmi160.txt
> > > > create mode 100644 Documentation/devicetree/bindings/iio/imu/bmi160.yaml
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/iio/imu/bmi160.txt b/Documentation/devicetree/bindings/iio/imu/bmi160.txt
> > > > deleted file mode 100644
> > > > index 900c169de00f..000000000000
> > > > --- a/Documentation/devicetree/bindings/iio/imu/bmi160.txt
> > > > +++ /dev/null
> > > > @@ -1,37 +0,0 @@
> > > > -Bosch BMI160 - Inertial Measurement Unit with Accelerometer, Gyroscope
> > > > -and externally connectable Magnetometer
> > > > -
> > > > -https://www.bosch-sensortec.com/bst/products/all_products/bmi160
> > > > -
> > > > -Required properties:
> > > > - - compatible : should be "bosch,bmi160"
> > > > - - reg : the I2C address or SPI chip select number of the sensor
> > > > - - spi-max-frequency : set maximum clock frequency (only for SPI)
> > > > -
> > > > -Optional properties:
> > > > - - interrupts : interrupt mapping for IRQ
> > > > - - interrupt-names : set to "INT1" if INT1 pin should be used as interrupt
> > > > - input, set to "INT2" if INT2 pin should be used instead
> > > > - - drive-open-drain : set if the specified interrupt pin should be configured as
> > > > - open drain. If not set, defaults to push-pull.
> > > > -
> > > > -Examples:
> > > > -
> > > > -bmi160@68 {
> > > > - compatible = "bosch,bmi160";
> > > > - reg = <0x68>;
> > > > -
> > > > - interrupt-parent = <&gpio4>;
> > > > - interrupts = <12 IRQ_TYPE_EDGE_RISING>;
> > > > - interrupt-names = "INT1";
> > > > -};
> > > > -
> > > > -bmi160@0 {
> > > > - compatible = "bosch,bmi160";
> > > > - reg = <0>;
> > > > - spi-max-frequency = <10000000>;
> > > > -
> > > > - interrupt-parent = <&gpio2>;
> > > > - interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
> > > > - interrupt-names = "INT2";
> > > > -};
> > > > diff --git a/Documentation/devicetree/bindings/iio/imu/bmi160.yaml b/Documentation/devicetree/bindings/iio/imu/bmi160.yaml
> > > > new file mode 100644
> > > > index 000000000000..6b464ce5ed0b
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/iio/imu/bmi160.yaml
> > > > @@ -0,0 +1,84 @@
> > > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > > > +%YAML 1.2
> > > > +---
> > > > +$id: http://devicetree.org/schemas/iio/imu/bmi160.yaml#
> > > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > > +
> > > > +title: Bosch BMI160
> > > > +
> > > > +maintainers:
> > > > + - can't find a mantainer, author is Daniel Baluta <daniel.baluta@xxxxxxxxx>
> > >
> > > Daniel is still active in the kernel, just not at Intel any more. +CC
> > >
> >
> > Oh ok thank you! Daniel are you still maintaining this driver?
> >
> > > > +
> > > > +description: |
> > > > + Inertial Measurement Unit with Accelerometer, Gyroscope and externally
> > > > + connectable Magnetometer
> > > > + https://www.bosch-sensortec.com/bst/products/all_products/bmi160
> > > > +
> > > > +properties:
> > > > + compatible:
> > > > + const: bosch,bmi160
> > > > +
> > > > + reg:
> > > > + maxItems: 1
> > > > + description: the I2C address or SPI chip select number of the sensor
> > >
> > > As standard for i2c and spi, usually no need to have a description line for
> > > this element.
> > >
> >
> > Thank you, will remove the description then.
> >
> > > > +
> > > > + spi-max-frequency:
> > > > + maxItems: 1
> > > > + description: set maximum clock frequency (required only for SPI)
> > >
> > > Standard spi binding. Probably doesn't need to be included here.
> > >
> >
> > So should I completely remove it from properties?
>
> Yes
>
>
> Thanks,
>
> Jonathan

Ok I will remove it completely in next patch,
Thank you,

Best regards,
Jonathan Albrieux