Re: [PATCH 1/2] dt-bindings: spi: Add Baikal-T1 System Boot SPI Controller binding

From: Rob Herring
Date: Thu May 21 2020 - 10:57:25 EST


On Mon, May 18, 2020 at 3:27 PM Serge Semin
<Sergey.Semin@xxxxxxxxxxxxxxxxxxxx> wrote:
>
> On Mon, May 18, 2020 at 09:26:59AM -0600, Rob Herring wrote:
> > On Fri, May 08, 2020 at 12:36:20PM +0300, Serge Semin wrote:
> > > Baikal-T1 Boot SPI is a part of the SoC System Controller and is
> > > responsible for the system bootup from an external SPI flash. It's a DW
> > > APB SSI-based SPI-controller with no interrupts, no DMA, with just one
> > > native chip-select available and a single reference clock. Since Baikal-T1
> > > SoC is normally booted up from an external SPI flash this SPI controller
> > > in most of the cases is supposed to be connected to a single SPI-nor
> > > flash. Additionally in order to provide a transparent from CPU point of
> > > view initial code execution procedure the system designers created an IP
> > > block which physically maps the SPI flash found at CS0 to a memory region.
> > >
> > > Co-developed-by: Ramil Zaripov <Ramil.Zaripov@xxxxxxxxxxxxxxxxxxxx>
> > > Signed-off-by: Ramil Zaripov <Ramil.Zaripov@xxxxxxxxxxxxxxxxxxxx>
> > > Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
> > > Cc: Alexey Malahov <Alexey.Malahov@xxxxxxxxxxxxxxxxxxxx>
> > > Cc: Thomas Bogendoerfer <tsbogend@xxxxxxxxxxxxxxxx>
> > > Cc: Paul Burton <paulburton@xxxxxxxxxx>
> > > Cc: Ralf Baechle <ralf@xxxxxxxxxxxxxx>
> > > Cc: John Garry <john.garry@xxxxxxxxxx>
> > > Cc: Chuanhong Guo <gch981213@xxxxxxxxx>
> > > Cc: Tomer Maimon <tmaimon77@xxxxxxxxx>
> > > Cc: Lee Jones <lee.jones@xxxxxxxxxx>
> > > Cc: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
> > > Cc: Arnd Bergmann <arnd@xxxxxxxx>
> > > Cc: linux-mips@xxxxxxxxxxxxxxx
> > > Cc: linux-spi@xxxxxxxxxxxxxxx
> > > ---
> > > .../bindings/spi/baikal,bt1-sys-ssi.yaml | 100 ++++++++++++++++++
> > > 1 file changed, 100 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/spi/baikal,bt1-sys-ssi.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/spi/baikal,bt1-sys-ssi.yaml b/Documentation/devicetree/bindings/spi/baikal,bt1-sys-ssi.yaml
> > > new file mode 100644
> > > index 000000000000..d9d3257d78f4
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/spi/baikal,bt1-sys-ssi.yaml
> > > @@ -0,0 +1,100 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > +# Copyright (C) 2020 BAIKAL ELECTRONICS, JSC
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/spi/baikal,bt1-sys-ssi.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: Baikal-T1 System Boot SSI Controller
> > > +
> > > +description: |
> > > + Baikal-T1 System Controller includes a Boot SPI Controller, which is
> > > + responsible for loading chip bootup code from an external SPI flash. In order
> > > + to do this transparently from CPU point of view there is a dedicated IP block
> > > + mapping the 16MB flash to a dedicated MMIO range. The controller is based on
> > > + the DW APB SSI IP-core but equipped with very limited resources: no IRQ,
> > > + no DMA, a single native CS being necessarily connected to a 16MB SPI flash
> > > + (otherwise the system won't bootup from the flash), internal Tx/Rx FIFO of
> > > + just 8 bytes depth. Access to DW APB SSI controller registers is mutually
> > > + exclusive from normal MMIO interface and from physically mapped SPI Flash
> > > + memory. So either one or another way of using the controller functionality
> > > + can be enabled at a time.
> > > +
> > > +maintainers:
> > > + - Serge Semin <fancer.lancer@xxxxxxxxx>
> > > +
> > > +allOf:
> > > + - $ref: spi-controller.yaml#
> > > +
> > > +properties:
> > > + compatible:
> > > + const: baikal,bt1-sys-ssi
> > > +
> > > + reg:
> > > + items:
> > > + - description: Baikal-T1 Boot Controller configuration registers
> > > + - description: Physically mapped SPI flash ROM found at CS0
> > > +
> > > + reg-names:
> > > + items:
> > > + - const: config
> > > + - const: map
> > > +
> > > + clocks:
> > > + description: SPI Controller reference clock source
> >
> > Can drop this.
>
> Ok.
>
> >
> > > + maxItems: 1
> > > +
> > > + clock-names:
> > > + items:
> > > + - const: ssi_clk
> > > +
> > > + num-cs:
> > > + const: 1
> > > +
> > > +patternProperties:
> > > + "^.*@[0-9a-f]+":
> > > + type: object
> > > + properties:
> > > + reg:
> > > + minimum: 0
> > > + maximum: 0
> > > +
> > > + spi-rx-bus-width:
> > > + const: 1
> > > +
> > > + spi-tx-bus-width:
> > > + const: 1
> >
> > What's the point of these 2 properties if they aren't required?
>
> Yes, they are optional, but this is a constraint on the bus-width parameters.
> DW APB SSI provides a single laned Tx and Rx.

Are you just trying to keep someone from saying 'spi-tx-bus-width: 2'
for example?

You could also say 'spi-tx-bus-width: false' here to disallow the
property. I guess the above is fine.

Rob