[PATCH v2 6/7] pinctrl: madera: Move binding over to dtschema

From: Charles Keepax
Date: Wed May 06 2020 - 11:58:22 EST


Signed-off-by: Charles Keepax <ckeepax@xxxxxxxxxxxxxxxxxxxxx>
---

New since v1, putting in the same series as Arizona since they share the
same regulator binding.

Thanks,
Charles

.../bindings/pinctrl/cirrus,madera-pinctrl.txt | 99 --------------
.../devicetree/bindings/pinctrl/cirrus,madera.yaml | 147 +++++++++++++++++++++
2 files changed, 147 insertions(+), 99 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt
deleted file mode 100644
index b0e36cf0d289e..0000000000000
--- a/Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt
+++ /dev/null
@@ -1,99 +0,0 @@
-Cirrus Logic Madera class audio codecs pinctrl driver
-
-The Cirrus Logic Madera codecs provide a number of GPIO functions for
-interfacing to external hardware and to provide logic outputs to other devices.
-Certain groups of GPIO pins also have an alternate function, normally as an
-audio interface.
-
-The set of available GPIOs, functions and alternate function groups differs
-between codecs so refer to the datasheet for the codec for further information
-on what is supported on that device.
-
-The properties for this driver exist within the parent MFD driver node.
-
-See also
- the core bindings for the parent MFD driver:
- Documentation/devicetree/bindings/mfd/madera.txt
-
- the generic pinmix bindings:
- Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
-
-Required properties of parent mfd node:
- - pinctrl-names : must be "default"
- - pinctrl-0 : a phandle to the node containing the subnodes containing default
- configurations
-
-Required subnodes:
- One subnode is required to contain the default settings. It contains an
- arbitrary number of configuration subnodes, one for each group or pin
- configuration you want to apply as a default.
-
-Required properties of configuration subnodes:
- - groups : name of one pin group to configure. One of:
- aif1, aif2, aif3, aif4, mif1, mif2, mif3, pdmspk1, pdmspk2,
- dmic4, dmic5, dmic6,
- gpio1, gpio2, ..., gpio40
- The gpioN groups select the single pin of this name for configuration
-
-Optional properties of configuration subnodes:
- Any configuration option not explicitly listed in the dts will be left at
- chip default setting.
-
- - function : name of function to assign to this group. One of:
- aif1, aif2, aif3, aif4, mif1, mif2, mif3, pdmspk1, pdmspk2,
- dmic3, dmic4, dmic5, dmic6,
- io, dsp-gpio, irq1, irq2,
- fll1-clk, fll1-lock, fll2-clk, fll2-lock, fll3-clk, fll3-lock,
- fllao-clk, fllao-lock,
- opclk, opclk-async, pwm1, pwm2, spdif,
- asrc1-in1-lock, asrc1-in2-lock, asrc2-in1-lock, asrc2-in2-lock,
- spkl-short-circuit, spkr-short-circuit, spk-shutdown,
- spk-overheat-shutdown, spk-overheat-warn,
- timer1-sts, timer2-sts, timer3-sts, timer4-sts, timer5-sts, timer6-sts,
- timer7-sts, timer8-sts,
- log1-fifo-ne, log2-fifo-ne, log3-fifo-ne, log4-fifo-ne, log5-fifo-ne,
- log6-fifo-ne, log7-fifo-ne, log8-fifo-ne,
-
- - bias-disable : disable pull-up and pull-down
- - bias-bus-hold : enable buskeeper
- - bias-pull-up : output is pulled-up
- - bias-pull-down : output is pulled-down
- - drive-push-pull : CMOS output
- - drive-open-drain : open-drain output
- - drive-strength : drive strength in mA. Valid values are 4 or 8
- - input-schmitt-enable : enable schmitt-trigger mode
- - input-schmitt-disable : disable schmitt-trigger mode
- - input-debounce : A value of 0 disables debounce, a value !=0 enables
- debounce
- - output-low : set the pin to output mode with low level
- - output-high : set the pin to output mode with high level
-
-Example:
-
-cs47l85@0 {
- compatible = "cirrus,cs47l85";
-
- pinctrl-names = "default";
- pinctrl-0 = <&cs47l85_defaults>;
-
- cs47l85_defaults: cs47l85-gpio-defaults {
- aif1 {
- groups = "aif1";
- function = "aif1";
- bias-bus-hold;
- };
-
- aif2 {
- groups = "aif2";
- function = "aif2";
- bias-bus-hold;
- };
-
- opclk {
- groups = "gpio1";
- function = "opclk";
- bias-pull-up;
- drive-strength = <8>;
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml
new file mode 100644
index 0000000000000..07a13429ca6c4
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml
@@ -0,0 +1,147 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/cirrus,madera.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic Madera class audio CODECs pinctrl driver
+
+maintainers:
+ - patches@xxxxxxxxxxxxxxxxxxxxx
+
+description: |
+ The Cirrus Logic Madera codecs provide a number of GPIO functions for
+ interfacing to external hardware and to provide logic outputs to other devices.
+ Certain groups of GPIO pins also have an alternate function, normally as an
+ audio interface.
+
+ The set of available GPIOs, functions and alternate function groups differs
+ between CODECs so refer to the datasheet for the CODEC for further information
+ on what is supported on that device.
+
+ The properties for this driver exist within the parent MFD driver node.
+
+ See also the core bindings for the parent MFD driver:
+
+ Documentation/devicetree/bindings/mfd/cirrus,madera.yaml
+
+ And the generic pinmix bindings:
+
+ Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+properties:
+ pinctrl-0:
+ description:
+ A phandle to the node containing the subnodes containing default
+ configurations.
+
+ pinctrl-names:
+ description:
+ A pinctrl state named "default" must be defined.
+ const: default
+
+patternProperties:
+ '^.*-pins$':
+ description:
+ One subnode is required to contain the default settings. It
+ contains an arbitrary number of configuration subnodes, one for
+ each group or pin configuration you want to apply as a default.
+ patternProperties:
+ '^.*-pin$':
+ type: object
+ allOf:
+ - $ref: "pincfg-node.yaml#"
+ - $ref: "pinmux-node.yaml#"
+ properties:
+ groups:
+ description:
+ Name of one pin group to configure.
+ enum: [ aif1, aif2, aif3, aif4, mif1, mif2, mif3, pdmspk1,
+ pdmspk2, dmic4, dmic5, dmic6, gpio1, gpio2, gpio3,
+ gpio4, gpio5, gpio6, gpio7, gpio7, gpio8, gpio9,
+ gpio10, gpio11, gpio12, gpio13, gpio14, gpio15,
+ gpio16, gpio17, gpio17, gpio18, gpio19, gpio20,
+ gpio21, gpio22, gpio23, gpio24, gpio25, gpio26,
+ gpio27, gpio27, gpio28, gpio29, gpio30, gpio31,
+ gpio32, gpio33, gpio34, gpio35, gpio36, gpio37,
+ gpio37, gpio38, gpio39 ]
+
+ function:
+ description:
+ Name of function to assign to this group.
+ enum: [ aif1, aif2, aif3, aif4, mif1, mif2, mif3,
+ pdmspk1, pdmspk2, dmic3, dmic4, dmic5,
+ dmic6, io, dsp-gpio, irq1, irq2, fll1-clk,
+ fll1-lock, fll2-clk, fll2-lock, fll3-clk,
+ fll3-lock, fllao-clk, fllao-lock, opclk,
+ opclk-async, pwm1, pwm2, spdif, asrc1-in1-lock,
+ asrc1-in2-lock, asrc2-in1-lock, asrc2-in2-lock,
+ spkl-short-circuit, spkr-short-circuit,
+ spk-shutdown, spk-overheat-shutdown,
+ spk-overheat-warn, timer1-sts, timer2-sts,
+ timer3-sts, timer4-sts, timer5-sts, timer6-sts,
+ timer7-sts, timer8-sts, log1-fifo-ne,
+ log2-fifo-ne, log3-fifo-ne, log4-fifo-ne,
+ log5-fifo-ne, log6-fifo-ne, log7-fifo-ne,
+ log8-fifo-ne ]
+
+ bias-disable:
+ description:
+ Disable pull-up and pull-down.
+
+ bias-bus-hold:
+ description:
+ Enable buskeeper.
+
+ bias-pull-up:
+ description:
+ Output is pulled-up.
+
+ bias-pull-down:
+ description:
+ Output is pulled-down.
+
+ drive-push-pull:
+ description:
+ CMOS output.
+
+ drive-open-drain:
+ description:
+ Open-drain output.
+
+ drive-strength:
+ description:
+ Drive strength in mA.
+ enum: [ 4, 8 ]
+
+ input-schmitt-enable:
+ description:
+ Enable schmitt-trigger mode.
+
+ input-schmitt-disable:
+ description:
+ Disable schmitt-trigger mode.
+
+ input-debounce:
+ description:
+ A zero value disables debounce, non-zero value enables
+ debounce.
+
+ output-low:
+ description:
+ Set the pin to output mode with low level.
+
+ output-high:
+ description:
+ Set the pin to output mode with high level.
+
+ additionalProperties: false
+
+ required:
+ - groups
+
+ additionalProperties: false
+
+required:
+ - pinctrl-0
+ - pinctrl-names
--
2.11.0