Re: [PATCH V2] ASoC: Intel: boards: Use FS as nau8825 sysclk in nau88125_* machine

From: RadosÅaw Biernacki
Date: Tue May 05 2020 - 10:24:04 EST


Thank you Pierre for the review!
answers inline

pt., 1 maj 2020 o 22:16 Pierre-Louis Bossart
<pierre-louis.bossart@xxxxxxxxxxxxxxx> wrote:
>
>
>
> On 5/1/20 2:31 PM, Radoslaw Biernacki wrote:
> > This single fix address two issues on machines with nau88125:
> > 1) Audio distortion, due to lack of required clock rate on MCLK line
> > 2) Loud audible "pops" on headphones if there is no sysclk during nau8825
> > playback power up sequence
> >
> > Explanation for:
> > 1) Due to Skylake HW limitation, MCLK pin can only output 24MHz clk
> > rate (it can be only connected to XTAL parent clk). The BCLK pin
> > can be driven by dividers and therefore FW is able to set it to rate
> > required by chosen audio format. According to nau8825 datasheet, 256*FS
> > sysclk gives the best audio quality and the only way to achieve this
> > (taking into account the above limitations) its to regenerate the MCLK
> > from BCLK on nau8825 side by FFL. Without required clk rate, audio is
> > distorted by added harmonics.
>
> The BCLK is going to be a multiple of 50 * Fs due to clocking
> restrictions. Can the codec regenerate a good-enough sysclk from this?

According to Intel, silicon has a limitation, on SKL/KBL only clk_id =
SKL_XTAL, .name = "xtal" is available for IO domain.
As mentioned in the commit:
MCLK is generated by using 24MHz Xtal directly or applying a divider
(so no way of achieving the rate required by audio format).
BCLK/FS is generated from 24MHz and uses dividers and additional
padding bits are used to match the clock source.
Next gen silicon has the possibility of using additional clock sources.

Summing up, using MCLK from SKL to NAU88L25 is not an option.
The only option we found is to use BCLK and regen the required clock
rate by FLL on the NAU88l25 side.

> >
> > 2) Currently Skylake does not output MCLK/FS when the back-end DAI op
> > hw_param is called, so we cannot switch to MCLK/FS in hw_param. This
> > patch reduces pop by letting nau8825 keep using its internal VCO clock
> > during widget power up sequence, until SNDRV_PCM_TRIGGER_START when
> > MCLK/FS is available. Once device resumes, the system will only enable
> > power sequence for playback without doing hardware parameter, audio
> > format, and PLL configure. In the mean time, the jack detecion sequence
> > has changed PLL parameters and switched to internal clock. Thus, the
> > playback signal distorted without correct PLL parameters. That is why
> > we need to configure the PLL again in SNDRV_PCM_TRIGGER_RESUME case.
>
> IIRC the FS can be controlled with the clk_ api with the Skylake driver,
> as done for some KBL platforms. Or is this not supported by the firmware
> used by this machine?

According to Ben, SKL had limitations in FW for managing the clk's
back in the days.
Can you point to the other driver you mention so we can cross check?

>
> > -static int skylake_nau8825_hw_params(struct snd_pcm_substream *substream,
> > - struct snd_pcm_hw_params *params)
> > +static int skylake_nau8825_trigger(struct snd_pcm_substream *substream, int cmd)
> > {
> > struct snd_soc_pcm_runtime *rtd = substream->private_data;
> > + struct snd_pcm_runtime *runtime = substream->runtime;
> > struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0);
> > - int ret;
> > -
> > - ret = snd_soc_dai_set_sysclk(codec_dai,
> > - NAU8825_CLK_MCLK, 24000000, SND_SOC_CLOCK_IN);
> > + int ret = 0;
> >
> > - if (ret < 0)
> > - dev_err(rtd->dev, "snd_soc_dai_set_sysclk err = %d\n", ret);
> > + switch (cmd) {
> > + case SNDRV_PCM_TRIGGER_START:
> > + ret = snd_soc_dai_set_sysclk(codec_dai, NAU8825_CLK_FLL_FS, 0,
> > + SND_SOC_CLOCK_IN);
> > + if (ret < 0) {
> > + dev_err(codec_dai->dev, "can't set FS clock %d\n", ret);
> > + break;
> > + }
> > + ret = snd_soc_dai_set_pll(codec_dai, 0, 0, runtime->rate,
> > + runtime->rate * 256);
> > + if (ret < 0)
> > + dev_err(codec_dai->dev, "can't set FLL: %d\n", ret);
> > + break;
> > + case SNDRV_PCM_TRIGGER_RESUME:
> > + ret = snd_soc_dai_set_pll(codec_dai, 0, 0, runtime->rate,
> > + runtime->rate * 256);
> > + if (ret < 0)
> > + dev_err(codec_dai->dev, "can't set FLL: %d\n", ret);
> > + msleep(20);
>
> is there a reason why you'd need a msleep for resume and not for start?

No. I think we missed this.
msleep() is needed to stabilize FLL.
Will fix in next rev.