Re: [PATCH v6 3/5] ARM: dts: add Protonic VT7 board

From: Marco Felsch
Date: Wed Apr 22 2020 - 03:04:51 EST


Hi Oleksij,

On 20-04-21 14:40, Oleksij Rempel wrote:
> The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch
> touchscreen display.
>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> Signed-off-by: Robin van der Gracht <robin@xxxxxxxxxxx>
> Signed-off-by: David Jander <david@xxxxxxxxxxx>
> Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6dl-prtvt7.dts | 472 ++++++++++++++++++++++++++++
> 2 files changed, 473 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 8ce744f1cbfc9..66ee89e7929f9 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-pico-hobbit.dtb \
> imx6dl-pico-nymph.dtb \
> imx6dl-pico-pi.dtb \
> + imx6dl-prtvt7.dtb \
> imx6dl-rex-basic.dtb \
> imx6dl-riotboard.dtb \
> imx6dl-sabreauto.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> new file mode 100644
> index 0000000000000..a948c7c6eb3ce
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -0,0 +1,472 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright (c) 2016 Protonic Holland
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-prti6q.dtsi"

Should we name it "imx6qdl-prt-common.dtsi"? Still don't like that this
dtsi comes from the 1st commit rather then having a single commit adding
the .dtsi but that is only my opinion.

> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/sound/fsl-imx-audmux.h>
> +
> +/ {
> + model = "Protonic VT7";
> + compatible = "prt,prtvt7", "fsl,imx6dl";
> +
> + memory@10000000 {
> + device_type = "memory";
> + reg = <0x10000000 0x20000000>;
> + };
> +
> + backlight_lcd: backlight-lcd {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 500000>;
> + brightness-levels = <0 20 81 248 1000>;
> + default-brightness-level = <20>;
> + num-interpolated-steps = <21>;

Do you need this fine granularity here? Just asking ;)

> + power-supply = <&reg_12v_bl>;
> + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;

Where gets this gpio muxed?

> + };
> +
> + display {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ipu1_disp>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";

Status not needed here.

> +
> + port@0 {
> + reg = <0>;
> +
> + display_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + display_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> + autorepeat;
> +
> + esc {
> + label = "GPIO Key ESC";
> + linux,code = <KEY_ESC>;
> + gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
> + };
> +
> + up {
> + label = "GPIO Key UP";
> + linux,code = <KEY_UP>;
> + gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
> + };
> +
> + down {
> + label = "GPIO Key DOWN";
> + linux,code = <KEY_DOWN>;
> + gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
> + };
> +
> + enter {
> + label = "GPIO Key Enter";
> + linux,code = <KEY_ENTER>;
> + gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
> + };
> +
> + cycle {
> + label = "GPIO Key CYCLE";
> + linux,code = <KEY_CYCLEWINDOWS>;
> + gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
> + };
> +
> + f1 {
> + label = "GPIO Key F1";
> + linux,code = <KEY_F1>;
> + gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
> + };
> +
> + f2 {
> + label = "GPIO Key F2";
> + linux,code = <KEY_F2>;
> + gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
> + };
> +
> + f3 {
> + label = "GPIO Key F3";
> + linux,code = <KEY_F3>;
> + gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
> + };
> +
> + f4 {
> + label = "GPIO Key F4";
> + linux,code = <KEY_F4>;
> + gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
> + };
> +
> + f5 {
> + label = "GPIO Key F5";
> + linux,code = <KEY_F5>;
> + gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
> + };
> +
> + f6 {
> + label = "GPIO Key F6";
> + linux,code = <KEY_F6>;
> + gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
> + };
> +
> + f7 {
> + label = "GPIO Key F7";
> + linux,code = <KEY_F7>;
> + gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
> + };
> +
> + f8 {
> + label = "GPIO Key F8";
> + linux,code = <KEY_F8>;
> + gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
> + };
> +
> + f9 {
> + label = "GPIO Key F9";
> + linux,code = <KEY_F9>;
> + gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
> + };
> +
> + f10 {
> + label = "GPIO Key F10";
> + linux,code = <KEY_F10>;
> + gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
> + };

Don't know if there is a common rule if the gpio key should be sorted
alphabetical too.

> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_leds>;
> +
> + led-debug0 {
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + panel {
> + compatible = "innolux,g070y2t0ec";

Did you send a patch for this panel?

> + backlight = <&backlight_lcd>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&display_out>;
> + };
> + };
> + };
> +
> + reg_12v_bl: regulator-bl-12v {

Nit, it's common to allign the pahndle and the name, so either:

reg_12v_bl -> regulator-12v-bl

or

reg_bl_12v -> regulator-bl-12v

also it would be cool to keep the first digit after the point like you
did it for the 1.8 regulator. So the result would be:

reg_12v0_bl -> regulator-12v0-bl

or

reg_bl_12v0 -> regulator-bl-12v0


> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_12v_bl>;
> + regulator-name = "12v-bl";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_1v8: regulator-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "prti6q-sgtl5000";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Line", "Line In Jack",
> + "Headphone", "Headphone Jack",
> + "Speaker", "External Speaker";
> + simple-audio-card,routing =
> + "MIC_IN", "Microphone Jack",
> + "LINE_IN", "Line In Jack",
> + "Headphone Jack", "HP_OUT",
> + "External Speaker", "LINE_OUT";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&ssi1>;
> + system-clock-frequency = <0>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&sgtl5000>;
> + bitclock-master;
> + frame-master;
> + };
> + };
> +};
> +
> +&clks {
> + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
> + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
> +};
> +
> +&ecspi2 {
> + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + status = "okay";
> +
> + tsc@0 {
> + compatible = "ti,tsc2046";
> + reg = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tsc>;
> + spi-max-frequency = <100000>;
> + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;

The this should be listed within the binding doc.

> + pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;

IRQ and the GPIO are the same gpio line?

> + vcc-supply = <&reg_3v3>;
> +
> + ti,vref-delay-usecs = /bits/ 16 <100>;
> +
> + ti,x-min = /bits/ 16 <0>;
> + ti,x-max = /bits/ 16 <8000>;
> + ti,y-min = /bits/ 16 <0>;
> + ti,y-max = /bits/ 16 <4800>;
> + ti,x-plate-ohms = /bits/ 16 <800>;
> + ti,y-plate-ohms = /bits/ 16 <300>;
> + ti,pressure-max = /bits/ 16 <4095>;
> +
> + ti,skip-samples = <2>;
> + ti,sample-period-msecs = <10>;
> + ti,report-period-msecs = <30>;
> +
> + ti,filter-tolerance = <80>;
> + ti,touch-resistance-threshold = <3500>;
> + };
> +};
> +
> +&audmux {

Pls, sort it alphabetical.

> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +
> + mux_ssi1 {
> + fsl,audmux-port = <0>;
> + fsl,port-config = <
> + IMX_AUDMUX_V2_PTCR_SYN 0
> + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
> + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
> + IMX_AUDMUX_V2_PTCR_TFSDIR 0
> + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
> + >;
> + };
> +
> + mux_pins3 {
> + fsl,audmux-port = <2>;
> + fsl,port-config = <
> + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
> + 0 IMX_AUDMUX_V2_PDCR_TXRXEN
> + >;
> + };
> +};
> +
> +&can1 {

This here too.

> + pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
> +};
> +
> +&i2c1 {
> + sgtl5000: codec@a {
> + compatible = "fsl,sgtl5000";
> + reg = <0xa>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_codec>;
> + #sound-dai-cells = <0>;
> + clocks = <&clks 201>;
> + VDDA-supply = <&reg_3v3>;
> + VDDIO-supply = <&reg_3v3>;
> + VDDD-supply = <&reg_1v8>;
> + };
> +};
> +
> +&i2c3 {
> + rtc@51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + };
> +
> + gpio_pca: gpio@74 {
> + compatible = "nxp,pca9539";
> + reg = <0x74>;
> + interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + };
> +};
> +
> +&ipu1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ipu1_csi0>;
> + status = "okay";
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display_in>;
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> + status = "okay";
> +};
> +
> +&snvs_poweroff {
> + status = "okay";
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +&ssi1 {
> + #sound-dai-cells = <0>;
> + fsl,mode = "i2s-slave";
> + status = "okay";
> +};
> +
> +&usbh1 {
> + status = "disabled";
> +};
> +
> +&vpu {
> + status = "disabled";
> +};

Why do you disable this nodes? You should drop it from the common .dtsi
if you disable them more than once.

> +&iomuxc {
> + pinctrl_audmux: audmuxgrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
> + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
> + >;
> + };
> +
> + pinctrl_can1phy: can1phy {
> + fsl,pins = <
> + /* CAN1_SR */
> + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
> + /* CAN1_TERM */
> + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
> + >;
> + };
> +
> + pinctrl_codec: codecgrp {
> + fsl,pins = <
> + /* AUDIO_nRESET */
> + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> + >;
> + };
> +
> + pinctrl_ipu1_csi0: ipu1csi0grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
> + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
> + /* ITU656_nRESET */
> + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
> + /* ITU656_nPDN */
> + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
> + >;
> + };

Why do you mux the the camera interface and have no camera device within
this dt.

> + pinctrl_ipu1_disp: ipudisp1grp {
> + fsl,pins = <
> + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0
> + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0
> +
> + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0
> + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0
> + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0
> + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0
> + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0
> + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0
> + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0
> + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0
> +
> + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0
> + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0
> + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0
> + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0
> + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0
> + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0
> + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0
> + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0
> +
> + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0
> + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0
> + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0
> + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0
> + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0
> + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0
> + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0
> + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0
> + >;
> + };
> +
> + pinctrl_leds: ledsgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
> + >;
> + };
> +
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
> + >;
> + };
> +
> + pinctrl_reg_12v_bl: 12blgrp {

Pls, keep the name scheme like the others.

Regards,
Marco

> + fsl,pins = <
> + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
> + >;
> + };
> +
> + pinctrl_tsc: tscgrp {
> +
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
> + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
> + >;
> + };
> +};