Re: [PATCH v4 2/3] fs: openat2: Extend open_how to allow userspace-selected fds

From: Josh Triplett
Date: Mon Apr 20 2020 - 17:14:44 EST


On Sun, Apr 19, 2020 at 08:44:04PM +1000, Aleksa Sarai wrote:
> On 2020-04-13, Josh Triplett <josh@xxxxxxxxxxxxxxxx> wrote:
> > Inspired by the X protocol's handling of XIDs, allow userspace to select
> > the file descriptor opened by openat2, so that it can use the resulting
> > file descriptor in subsequent system calls without waiting for the
> > response to openat2.
> >
> > In io_uring, this allows sequences like openat2/read/close without
> > waiting for the openat2 to complete. Multiple such sequences can
> > overlap, as long as each uses a distinct file descriptor.
>
> I'm not sure I understand this explanation -- how can you trigger a
> syscall with an fd that hasn't yet been registered (unless you're just
> hoping the race goes in your favour)?

See the response from Jens for an explanation of how this works in
io_uring.

> > Add a new O_SPECIFIC_FD open flag to enable this behavior, only accepted
> > by openat2 for now (ignored by open/openat like all unknown flags). Add
> > an fd field to struct open_how (along with appropriate padding, and
> > verify that the padding is 0 to allow replacing the padding with a field
> > in the future).
> >
> > The file table has a corresponding new function
> > get_specific_unused_fd_flags, which gets the specified file descriptor
> > if O_SPECIFIC_FD is set (and the fd isn't -1); otherwise it falls back
> > to get_unused_fd_flags, to simplify callers.
> >
> > The specified file descriptor must not already be open; if it is,
> > get_specific_unused_fd_flags will fail with -EBUSY. This helps catch
> > userspace errors.
> >
> > When O_SPECIFIC_FD is set, and fd is not -1, openat2 will use the
> > specified file descriptor rather than finding the lowest available one.
>
> I still don't like that you can enable this feature with O_SPECIFIC_FD
> but then disable it by specifying fd as -1. I understand why this is
> needed for pipe2() and socketpair() and that's totally fine, but I don't
> think it makes sense for openat2() or other interfaces where there's
> only one fd being returned -- what does it mean to say "give me a
> specific fd, but actually I don't care what it is"?
>
> I know this is a trade-off between consistency of O_SPECIFIC_FD
> interfaces and having wart-less interfaces for each syscall, but I don't
> think it breaks consistency to say "syscalls that only give you one fd
> don't have a second way of disabling the feature -- just don't pass
> O_SPECIFIC_FD".

I think there's value in the orthogonality, and -1 can never be a valid
file descriptor. If this becomes a sticking point, it could certainly be
changed (just modify pipe2 to remove the O_SPECIFIC_FD flag if passed
-1), but at the same time, I'd rather have this logic implemented once
with a uniform semantic no matter what syscall uses it.

> > struct open_how {
> > __u64 flags;
> > __u64 mode;
> > __u64 resolve;
> > + __u32 fd;
> > + __u32 pad; /* Must be 0 in the current version */
>
> Small nit: This field should be called __padding to make it more
> explicit it's something internal and shouldn't be looked at by
> userspace. And the comment should just be "must be zeroed".

Good point. Done in v5.

> > --- a/tools/testing/selftests/openat2/openat2_test.c
> > +++ b/tools/testing/selftests/openat2/openat2_test.c
> > @@ -40,7 +40,7 @@ struct struct_test {
> > int err;
> > };
> >
> > -#define NUM_OPENAT2_STRUCT_TESTS 7
> > +#define NUM_OPENAT2_STRUCT_TESTS 8
> > #define NUM_OPENAT2_STRUCT_VARIATIONS 13
> >
> > void test_openat2_struct(void)
> > @@ -52,6 +52,9 @@ void test_openat2_struct(void)
> > { .name = "normal struct",
> > .arg.inner.flags = O_RDONLY,
> > .size = sizeof(struct open_how) },
> > + { .name = "v0 struct",
> > + .arg.inner.flags = O_RDONLY,
> > + .size = OPEN_HOW_SIZE_VER0 },
> > /* Bigger struct, with zeroed out end. */
> > { .name = "bigger struct (zeroed out)",
> > .arg.inner.flags = O_RDONLY,
> > @@ -155,7 +158,7 @@ struct flag_test {
> > int err;
> > };
> >
> > -#define NUM_OPENAT2_FLAG_TESTS 23
> > +#define NUM_OPENAT2_FLAG_TESTS 29
> >
> > void test_openat2_flags(void)
> > {
> > @@ -223,6 +226,24 @@ void test_openat2_flags(void)
> > { .name = "invalid how.resolve and O_PATH",
> > .how.flags = O_PATH,
> > .how.resolve = 0x1337, .err = -EINVAL },
> > +
> > + /* O_SPECIFIC_FD tests */
> > + { .name = "O_SPECIFIC_FD",
> > + .how.flags = O_RDONLY | O_SPECIFIC_FD, .how.fd = 42 },
> > + { .name = "O_SPECIFIC_FD if fd exists",
> > + .how.flags = O_RDONLY | O_SPECIFIC_FD, .how.fd = 2,
> > + .err = -EBUSY },
> > + { .name = "O_SPECIFIC_FD with fd -1",
> > + .how.flags = O_RDONLY | O_SPECIFIC_FD, .how.fd = -1 },
> > + { .name = "fd without O_SPECIFIC_FD",
> > + .how.flags = O_RDONLY, .how.fd = 42,
> > + .err = -EINVAL },
> > + { .name = "fd -1 without O_SPECIFIC_FD",
> > + .how.flags = O_RDONLY, .how.fd = -1,
> > + .err = -EINVAL },
> > + { .name = "existing fd without O_SPECIFIC_FD",
> > + .how.flags = O_RDONLY, .how.fd = 2,
> > + .err = -EINVAL },
>
> It would be good to add a test to make sure that a non-zero value of
> how->__padding also gives -EINVAL.

Done in v5.

- Josh Triplett