Re: [PATCH v11 1/2] media: dt-bindings: media: xilinx: Add Xilinx MIPI CSI-2 Rx Subsystem

From: Laurent Pinchart
Date: Sun Apr 19 2020 - 11:45:38 EST


Hi Vishal,

On Sun, Apr 19, 2020 at 06:43:07PM +0300, Laurent Pinchart wrote:
> On Fri, Apr 10, 2020 at 01:14:23AM +0530, Vishal Sagar wrote:
> > Add bindings documentation for Xilinx MIPI CSI-2 Rx Subsystem.
> >
> > The Xilinx MIPI CSI-2 Rx Subsystem consists of a CSI-2 Rx controller, a
> > DPHY in Rx mode, an optional I2C controller and a Video Format Bridge.
>
> The AXI IIC was removed from the subsystem in v4.1, you could drop it
> from the commit message too.
>
> > Signed-off-by: Vishal Sagar <vishal.sagar@xxxxxxxxxx>
> > Reviewed-by: Hyun Kwon <hyun.kwon@xxxxxxxxxx>
> > Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> > Reviewed-by: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx>
> > ---
> > v11
> > - Modify compatible string from 4.0 to 5.0
> >
> > v10
> > - No changes
> >
> > v9
> > - Fix xlnx,vfb description.
> > - s/Optional/Required endpoint property.
> > - Move data-lanes description from Ports to endpoint property section.
> >
> > v8
> > - Added reset-gpios optional property to assert video_aresetn
> >
> > v7
> > - Removed the control name from dt bindings
> > - Updated the example dt node name to csi2rx
> >
> > v6
> > - Added "control" after V4L2_CID_XILINX_MIPICSISS_ACT_LANES as suggested by Luca
> > - Added reviewed by Rob Herring
> >
> > v5
> > - Incorporated comments by Luca Cersoli
> > - Removed DPHY clock from description and example
> > - Removed bayer pattern from device tree MIPI CSI IP
> > doesn't deal with bayer pattern.
> >
> > v4
> > - Added reviewed by Hyun Kwon
> >
> > v3
> > - removed interrupt parent as suggested by Rob
> > - removed dphy clock
> > - moved vfb to optional properties
> > - Added required and optional port properties section
> > - Added endpoint property section
> >
> > v2
> > - updated the compatible string to latest version supported
> > - removed DPHY related parameters
> > - added CSI v2.0 related property (including VCX for supporting upto 16
> > virtual channels).
> > - modified csi-pxl-format from string to unsigned int type where the value
> > is as per the CSI specification
> > - Defined port 0 and port 1 as sink and source ports.
> > - Removed max-lanes property as suggested by Rob and Sakari
> > .../bindings/media/xilinx/xlnx,csi2rxss.txt | 116 ++++++++++++++++++
> > 1 file changed, 116 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt
> > new file mode 100644
> > index 000000000000..9269a5c880aa
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt
>
> YAML is the recommended form for new DT bindings. This wasn't a
> requirement when the first version of this series was submitted, and I
> understand it can be frustrating to chase a moving target, so I can help
> with the YAML conversion once we sort out the questions below.
>
> > @@ -0,0 +1,116 @@
> > +Xilinx MIPI CSI2 Receiver Subsystem Device Tree Bindings
>
> Nitpicking, it's CSI-2, not CSI2.
>
> > +--------------------------------------------------------
> > +
> > +The Xilinx MIPI CSI2 Receiver Subsystem is used to capture MIPI CSI2 traffic
> > +from compliant camera sensors and send the output as AXI4 Stream video data
> > +for image processing.
> > +
> > +The subsystem consists of a MIPI DPHY in slave mode which captures the
>
> And D-PHY, not DPHY :-)
>
> > +data packets. This is passed along the MIPI CSI2 Rx IP which extracts the
> > +packet data. The optional Video Format Bridge (VFB) converts this data to
> > +AXI4 Stream video data.
> > +
> > +For more details, please refer to PG232 Xilinx MIPI CSI-2 Receiver Subsystem.
>
> If I understand correctly, this DT binding covers the CSI-2 RX
> Controller and the optional Video Format Bridge, but leaves the D-PHY
> out, right ? I think this should be clarified, as the "CSI-2 receiver
> subsystem" includes the D-PHY.

I forgot to mention that if the PHY isn't included in the bindings, then
it should be referenced through a "phys" property.

> > +
> > +Required properties:
> > +--------------------
> > +- compatible: Must contain "xlnx,mipi-csi2-rx-subsystem-5.0".
>
> Is PG232 v5.0 available ? The most recent version I've found was PG232
> v4.1.
>
> > +- reg: Physical base address and length of the registers set for the device.
> > +- interrupts: Property with a value describing the interrupt number.
> > +- clocks: List of phandles to AXI Lite and Video clocks.
> > +- clock-names: Must contain "lite_aclk" and "video_aclk" in the same order
> > + as clocks listed in clocks property.
>
> The subsystem documentation also mentions a dphy_clk_200M. Is that
> routed to the D-PHY only, or is it also needed for the CSI-2 RX ?
>
> > +- xlnx,csi-pxl-format: This denotes the CSI Data type selected in hw design.
> > + Packets other than this data type (except for RAW8 and User defined data
> > + types) will be filtered out. Possible values are as below -
> > + 0x1E - YUV4228B
> > + 0x1F - YUV42210B
> > + 0x20 - RGB444
> > + 0x21 - RGB555
> > + 0x22 - RGB565
> > + 0x23 - RGB666
> > + 0x24 - RGB888
> > + 0x28 - RAW6
> > + 0x29 - RAW7
> > + 0x2A - RAW8
> > + 0x2B - RAW10
> > + 0x2C - RAW12
> > + 0x2D - RAW14
> > + 0x2E - RAW16
> > + 0x2F - RAW20
>
> Isn't this property required only when the VFB is present ?
>
> > +
> > +
> > +Optional properties:
> > +--------------------
> > +- xlnx,vfb: Present when Video Format Bridge is enabled in IP configuration
> > +- xlnx,en-csi-v2-0: Present if CSI v2 is enabled in IP configuration.
>
> Unless I'm mistaken, this feature is available starting at v4 of the IP
> core.
>
> > +- xlnx,en-vcx: When present, there are maximum 16 virtual channels, else
> > + only 4. This is present only if xlnx,en-csi-v2-0 is present.
> > +- xlnx,en-active-lanes: present if the number of active lanes can be
> > + re-configured at runtime in the Protocol Configuration Register.
> > + Otherwise all lanes, as set in IP configuration, are always active.
> > +- reset-gpios: Optional specifier for a GPIO that asserts video_aresetn.
>
> Should lite_aresetn also be supported ? We can add a lite-reset-gpios
> property later, but maybe we should name this video-reset-gpios ? As the
> video_aresetn signal is the main reset I don't mind keeping the name
> reset-gpios either. It's up to you.
>
> > +
> > +Ports
> > +-----
> > +The device node shall contain two 'port' child nodes as defined in
> > +Documentation/devicetree/bindings/media/video-interfaces.txt.
> > +
> > +The port@0 is a sink port and shall connect to CSI2 source like camera.
> > +
> > +The port@1 is a source port and can be connected to any video processing IP
> > +which can work with AXI4 Stream data.
> > +
> > +Required port properties:
> > +--------------------
> > +- reg: 0 - for sink port.
> > + 1 - for source port.
>
> Don't you need a second source port for embedded non-image data ? If my
> understanding is correct that port can be enabled or disabled through
> the CSI_EMB_NON_IMG parameter, so it should be optional in DT too. We
> can possibly leave it out for now, it can be added later in a
> backward-compatible way.
>
> > +
> > +Required endpoint property:
> > +---------------------------
> > +- data-lanes: specifies MIPI CSI-2 data lanes as covered in video-interfaces.txt.
> > + This is required only in the sink port 0 endpoint which connects to MIPI CSI2
> > + source like sensor. The possible values are:
> > + 1 - For 1 lane enabled in IP.
> > + 1 2 - For 2 lanes enabled in IP.
> > + 1 2 3 - For 3 lanes enabled in IP.
> > + 1 2 3 4 - For 4 lanes enabled in IP.
> > +
> > +Example:
> > +
> > + xcsi2rxss_1: csi2rx@a0020000 {
> > + compatible = "xlnx,mipi-csi2-rx-subsystem-5.0";
> > + reg = <0x0 0xa0020000 0x0 0x10000>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <0 95 4>;
> > + xlnx,csi-pxl-format = <0x2a>;
> > + xlnx,vfb;
> > + xlnx,en-active-lanes;
> > + xlnx,en-csi-v2-0;
> > + xlnx,en-vcx;
> > + clock-names = "lite_aclk", "video_aclk";
> > + clocks = <&misc_clk_0>, <&misc_clk_1>;
> > + reset-gpios = <&gpio 86 GPIO_ACTIVE_LOW>;
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + /* Sink port */
> > + reg = <0>;
> > + csiss_in: endpoint {
> > + data-lanes = <1 2 3 4>;
> > + /* MIPI CSI2 Camera handle */
> > + remote-endpoint = <&camera_out>;
> > + };
> > + };
> > + port@1 {
> > + /* Source port */
> > + reg = <1>;
> > + csiss_out: endpoint {
> > + remote-endpoint = <&vproc_in>;
> > + };
> > + };
> > + };
> > + };

--
Regards,

Laurent Pinchart